DeWalt DCD200 Instruction Manual page 30

ENglIsh
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Cable Removal from the Drain Snake and
Cable Drum Installation (Fig. A)

WARNING: To reduce the risk of injury, wear safety
goggles or glasses with side shields. Always wear
leather gloves with latex gloves inside. The cable is
under stress and can unwind unexpectedly. Cable end
feature may be sharp.
Remove the cable for cleaning after each use.
To Remove the Cable:
1. Remove the battery pack from the tool.
2. Pull the front handle 10
unlocked position.
3. With the tool supported vertically, remove the four
screws from the drum cover

WARNING: The cable is under stress and can uncoil
unexpectedly. Keep pressure on the drum cover so it
does not uncoil.
4. Carefully lift the drum cover up, reach underneath to hold
the cable firmly while pulling off the drum cover
front handle 10 to expose the inner drum
28
out away from the tool to the
9 .
and
9
12 .
5. Remove the cable from the drum cover and front handle
and tuck it into the inner drum. Set the drum cover aside.
6. Carefully remove the inner drum with cable from
the drain snake.
7. When cleaning the cable, carefully uncoil the cable from
the inner drum. Refer to Cleaning under Maintenance.
To Install the Cable:
1. Remove the battery pack from the tool.
2. Pull the front handle 10
unlocked position.
3. Remove the four screws from the drum cover
4. Fully wind the clean, dry cable into the inner drum
following the cable direction symbol

WARNING: Winding the cable in the wrong direction
could cause the tool to apply excessive torque causing
the cable to kink during bind up.

WARNING: Never install a new cable by threading
it through the front handle on the tool. Always
disassemble the drum cover so you can be sure the
cable is wound in the proper direction.
5. Place the inner drum with cable back into the tool.
6. Carefully pull the cable bulb end
drum and feed it through the front handle.

WARNING: The cable is under stress and can unwind
unexpectedly. Keep pressure on the cable so it does
not unwind.
7. Place the drum cover and front handle over the inner
drum and reinstall the four screws. Tighten securely.
NoTE: If the unit is unbalanced and/or vibrates
unnecessarily, the cable may be wound poorly.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. E)
NoTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack 5
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 6 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
out away from the tool to the
9 .
12
14 (Fig. A).
13 out of the inner
into the tool handle, align the