Related Manuals for Toro 23106
Summary of Contents for Toro 23106
- Page 1 Form No. 3443-247 Rev C Backhoe Compact Tool Carrier Model No. 23106—Serial No. 321000001 and Up *3443-247* Register at www.Toro.com. Original Instructions (EN)
- Page 2 1. Model and serial number location The backhoe attachment is intended to be used on a Toro compact tool carrier. It is designed primarily for digging soil for various applications at jobsites. Using this product for purposes other than its intended use Model No.
-
Page 3: General Safety
Safety distribution changes with attachments. This attachment makes the front of machine the heavy end. • DANGER Keep the attachment in the lowered position when on slopes. Raising the attachment on a There may be buried utility lines in the work slope affects the stability of the machine. -
Page 4: Maintenance And Storage Safety
Maintenance and Storage • Do not dig within 91 cm (3 ft) of the backhoe or stabilizers. Safety • Do not overload the machine capacity by attempting to use the backhoe too fast. • Check fasteners at frequent intervals for proper tightness to ensure that the equipment is in safe •... - Page 5 decal145-1851 145-1851 1. Warning—read the Operator’s Manual. 4. Tipping hazard—do not move the traction unit while seated on the backhoe; install the counterweight (if applicable); lower the stabilizers. 2. Warning—keep bystanders away. 5. Explosion and electric shock hazards—call your local utility company before digging;...
-
Page 6: Adjusting The Seat
Setup You must obtain and install the Backhoe Kit appropriate for your traction unit. Use the instructions Adjusting the Seat provided in this section to install these kits. No Parts Required Procedure Preparing the Machine CAUTION The seat mounting bracket has several pinch No Parts Required points. -
Page 7: Product Overview
Stabilizer Control Levers Product Overview Move the stabilizer control levers forward to lower the stabilizers and backward to raise the stabilizers. Boom Control Lever Move the boom control lever forward to lower the boom and backward to raise the boom. Move the boom control lever to the right to swing the boom to the right and move it left to swing the boom to the left. -
Page 8: Operation
To ensure optimum performance and continued safety this form of injury; otherwise, gangrene may certification of the machine, use only genuine Toro result. replacement parts and accessories. Replacement parts and accessories made by other manufacturers •... -
Page 9: Preparing For Operation
WARNING If you do not fully seat the quick-attach pins through the attachment mount plate, the attachment could fall off the machine, crushing you or bystanders. Ensure that the quick-attach pins are fully seated in the attachment mount plate. Preparing for Operation Drive to the work location. - Page 10 To empty the bucket, swing it to the left or right and Fully raise the boom, retract the dipper, and curl extend the dipper and uncurl bucket, dumping the the bucket rearward (Figure 11). Ensure that load (Figure 10). you center the boom locking pin holes as much as possible.
-
Page 11: Operating Tips
g352158 Figure 13 1. Pin Operating Tips • Do not take large bites of soil. Instead, sweep the bucket through the soil using the swinging motion of the dipper a few inches deep at a time. • If the bucket catches in the soil, uncurl the bucket, raise the boom slightly, and continue digging. -
Page 12: Recommended Maintenance Schedule(S)
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check all bolts and nuts for proper tightness and tighten them if needed. After the first hour • Grease all fittings. Before each use or daily • Inspect for leaks. Every 25 hours •... - Page 13 Storage Before long term storage wash the attachment with mild detergent and water to remove dirt and grime. Apply grease to all grease fittings. Check and tighten all bolts, nuts, and screws. Repair or replace any parts that are damaged or worn.
-
Page 14: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The backhoe does not operate. 1. The hydraulic coupler not completely 1. Check and tighten all couplers. connected. 2. The auxiliary-hydraulics valve on the 2. Engage the valve. traction unit is not fully engaged. 3. - Page 15 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 16 California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.