Related Manuals for Toro 66210T
Summary of Contents for Toro 66210T
- Page 1 Form No. 3445-454 Rev A Revolution 60V String Trimmer Model No. 66210T—Serial No. 323000001 and Up *3445-454* Register at www.Toro.com. Original Instructions (EN)
- Page 2 It is designed to use Toro 60V lithium-ion battery packs. These battery packs are designed to be charged only by Toro 60V lithium-ion battery chargers. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
-
Page 3: Important Safety Instructions
If the tool strikes an object or starts to vibrate, immediately shut off the tool, wait for all moving Use only the battery pack specified by Toro. parts to stop, and disconnect the battery before Using other accessories and attachments may examining the tool for damage. - Page 4 Do not disassemble the battery pack. • Replace the battery pack with a genuine Toro battery pack only; using another type of battery pack may cause a fire or risk of injury. • Keep battery packs out of the reach of children and in the original packaging until you are ready to use them.
-
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal145-2332 145-2332 1. Do not dispose improperly. decal139-8263 139-8263 1. - Page 6 Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Auxiliary handle assembly Install the auxiliary handle. Rear guard Front guard Install the guard. Socket-head screw Button-head screw – No parts required Install the harness.
-
Page 7: Installing The Auxiliary Handle
Installing the Auxiliary Handle Parts needed for this procedure: Auxiliary handle assembly Procedure Separate the auxiliary handle from the lower handle bracket by unscrewing the handle-lock knob and removing the socket head bolt (A of Figure Important: The bolt may be wedged into the plastic of the handle; lightly tap the bottom of the bolt until it is free from the handle. -
Page 8: Installing The Guard
Installing the Guard Parts needed for this procedure: Rear guard Front guard Socket-head screw Button-head screw Procedure Align the guard so that the tab on the mount slides into the slot (A of Figure Install and tighten the socket-head screw to secure the guard to the mount (B of Figure g379323 Figure 4... - Page 9 g399659 Figure 5 1. Front guard 3. Button-head screws 2. Rear guard...
-
Page 10: Installing The Harness
The strap length is adjustable; slide the strap adjuster up to decrease the length of the strap, or down to increase the length of the strap (Figure If there you ever need to rapidly remove the harness, Installing the Harness disconnect the quick-release buckle as follows: Press in on the sides of the buckle (A of Figure... -
Page 11: Product Overview
Authorized Service Dealer or authorized Toro 4. Auxiliary handle 8. Rod guard distributor or go to www.Toro.com for a list of all approved attachments and accessories. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. -
Page 12: Operation
Shutting Off the Trimmer Operation To shut off the trimmer, release both triggers. Starting the Trimmer Whenever you are not using the trimmer or are transporting the trimmer to or from the work area, Ensure that the vents on the trimmer are clear remove the battery pack. -
Page 13: Operating Tips
Advancing the Line Using the Bump Feed Run the tool at full throttle. Tap the bump head on the ground to advance the line. The line advances each time the bump head is tapped. Note: Do not hold the bump head on the ground while running the trimmer. -
Page 14: Maintenance
Maintenance After each use of the trimmer, complete the following: Remove the battery from the trimmer. Wipe the trimmer clean with a damp cloth. Do not hose the trimmer down or submerge it in water. CAUTION g367291 The line cutoff blade on the deflector is Figure 15 sharp and can cut you. - Page 15 Replacing the Trimmer With the metal rod securing the trimmer head, rotate the trimmer head clockwise to remove it Head from the threaded gearcase post (Figure 17). Remove the battery pack from the trimmer. Align the hole in the cup plate with the hole in the trimmer gearcase (Figure 16).
- Page 16 Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 11). Important: If you are storing the battery pack for the off-season, charge it until 2 or 3 LED indicators turn green on the battery.
-
Page 17: Troubleshooting
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem Possible Cause Corrective Action The tool does not run or does not run 1. - Page 18 Notes:...
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.