Table of Contents
Advertisement
FOLDING THE BACKREST FORWARD (REPACKING)
CAUTION
•
Keep hands, feet, children, objects, etc., clear of openings on the unit, including seat, armrests and legrest; gaps
between the unit and the floor; and the backrest's range of movement when being folded forward.
Failure to do so could result in injury due to pinching.
•
The unit should not be turned on and the controls should not be operated on when the backrest is folded forward.
Failure to follow these instructions could result in injury due to pinching.
•
The unit should not be climbed on and objects should not be placed on the unit when the backrest is folded forward.
Failure to follow these instructions could result in damage to the unit.
•
In the interests of safety, the backrest should always be folded forward by two persons.
1
Press the OFF/ON button to switch off the power.
2
Slide the power switch to the "off" position, lock it, and then unplug the power cord.
3
Remove the back cushion and the pillow from the unit.
4
Remove the armrest from the unit.
Refer to "INSTALL THE ARMRESTS ON THE UNIT" on page 6 and remove them in
reverse order.
5
Insert a screwdriver into the opening for the backrest latch
approx. 4 cm from the upper edge of the opening (until the
screwdriver contacts the backrest latch).
6
Push tip of screwdriver downward approx. 2.5 cm to
release backrest latch.
7
Pull out screwdriver when pushing of backrest toward
seat begins.
*Be careful to avoid catching the controller or the cord between the backrest and the seat.
* It is recommended that you move the unit before folding the backrest (upright
position). When the backrest is folded, it is not fixed and is unstable.
15
15-16
TROUBLESHOOTING
Problem
Cause and Remedy
Motor Noises
•
It sounds and feels like the massage heads are straining to get over wrinkles in the cloth.
•
The motor groans when it comes under load.
•
There is excessive noise during Tapping. (The noise is greater at the top of the unit.)
•
There is a creaking noise when the massage heads are in operation.
•
There is a rattling sound when the massage heads move up or down.
•
The belt can be heard rotating.
•
There is a rubbing sound produced by the massage heads rubbing on the seat fabric.
•
There is a noise when the backrest cushion moves over the armrest when the seat is reclining.
•
There is a noise when I sit down.
•
There is a strange sound when the massage heads move in and out.
•
When the power switch is turned on there is a humming sound.
•
Air massage-related sounds. There is a hissing sound of air escaping. There is a humming sound from the pump.
•
The legrest rattles.
•
There is operational noise of valves under the seat.
•
There is an unstable sound when air escapes during the leg stretch.
These sounds are perfectly normal and will not have any effect on the operation of the unit.
7
7
The massage heads stop during operation.
When excessive force is applied to the massage heads during operation, in the interests of safety the massage heads may stop moving.
If all markings and buttons on the controller start to flash, which is extremely unusual, turn off the power switch, wait for
approximately 10 seconds and then turn the power switch on again. If the massage heads stop again, position yourself so
that your back is not completely in contact with the backrest.
The massage heads do not come up to the shoulder or neck.
5
5
The position of the massage heads is incorrect.
The height of the left and right massage heads is different.
6
6
An alternating tapping method is employed, which means that this phenomenon will naturally occur.
There is nothing wrong with the unit.
It is not possible to recline the unit.
The legrest cannot be raised or lowered.
If the unit encounters an obstacle or if excessive force is exerted on it during operation, in the interests of safety the unit will
come to a stop.
If all markings and buttons on the controller start to flash, which is extremely unusual, turn off the power switch, wait for
approximately 10 seconds and then turn the power switch on again.
Reclining does not take place even though a massage is started in pre-programs.
(The seat does not automatically recline.)
In some cases the seat may not automatically recline depending on the position (angle) of the backrest or the legrest.
Automatic reclining will not activate when the backrest is reclined to flat position more than massage position and legrest is
in upper position.
When you use the manual operation only for legs, automatic reclining will not activate.
The backrest does not return to the upright position.
The backrest will not return to the upright position if the timer is activated or the
(Pressing
It is not possible to switch from Swedish and Knead to Hawaiian and Compression.
Switching can be hindered when the user's body weight is not resting on the massage heads. Shift your weight so that your
body is contact with the massage heads.
The legrest will not return to its original position.
If the length of the legrest has been extended, the legrest will strike the floor, preventing from returning to its original
position. Try again after retracting it to its original length.
The unit will not operate at all.
•
The power cord has been disconnected.
•
The power switch on the unit has not been turned on.
•
A Pre-Program button or Manual Operation button hasn't been pressed after pressing
The unit has been damaged.
Stop using the unit immediately.
The power cord or power plug is abnormally hot.
Stop using the unit immediately.
See Warning No. 17 on page 1, and No. 9 and 10 on page .
twice will return the backrest to its original position.)
(See Page 10)
button is pressed.
(See Page 1)
(See Pages 7 and 8)
(See Page 8)
.
(See Pages 9, 11 and 1)
16
2010/07/09
11:16:40
Advertisement
Table of Contents
