Specifications - Kenwood CS-5170 Instruction Manual

C R T
Acceleration Voltage
Display Area
V E R T I C A L A X I S (CH1 and C H 2 )
Sensitivity
Attenuator
Input Impedance
Frequency Frequency DC
Response Response
A C
Rise Time
Signal Delay Time
Crosstalk
Operating Modes Operating Modes Operating Modes Operating Modes Operating Modes c m
C H 2
A L T
C H O P
A D D
Chop Frequency
Channel Polarity
/f\ Maximum Input Voltage
H O R I Z O N T A L A X I S Input thru C H 2 , x 10 M A G not included
Operating Modes
Sensitivity
Input Impedance
Frequency Frequency DC
Response Response
A C
X - Y Phase Difference
A Maximum Input Voltage
S W E E P
Type Type Type Type A
A L T
B
X - Y
S w e e p Time S w e e p Time A
B
S w e e p Magnification
Linearity
Holdoff
Trace Separation
Delayed S w e e p
Delay Time
4

SPECIFICATIONS

C S - 5 1 7 0
1 5 0 mm rectangular with internal graticule
1 mV/div to 5 V/div: 1 mV to 2 mV/div ± 5 % , 5 mV/div to 5 V/div ± 3 %
1 2 steps, 1 mV/div to 5 V/div in 1-2-5 sequence
Vernier control for fully adjustable sensitivity between steps
DC to 1 0 0 MHz, within - 3 dB (5 mV/div to 5 V/div)
DC to 2 0 MHz, within - 3 dB (1 mV/div to 2 mV/div)
5 Hz to 1 0 0 MHz, within - 3 dB (5 mV/div to 5 V/div)
5 Hz to 2 0 MHz, within - 3 dB (1 mV/div to 2 mV/div)
Adequate to identify leading edge
T w o - w a v e f o r m display, alternately
T w o - w a v e f o r m display, chopped
Normal or inverted, channel 2 only inverted
5 0 0 Vp-p or 2 5 0 V (DC + A C peak)
X - Y operation is selectable with HORIZ MODE s w i t c h
A sweep (intensified for duration of B sweep) and B sweep (delayed sweep) alternating
0 . 0 5 ,ns/div to 0 . 5 s/div ± 3 % , in 2 2 ranges, in 1-2-5 sequence
Vernier control for fully adjustable s w e e p time between steps
0 . 0 5 fis/d'w to 5 0 ms/div ± 3 % , in 19 ranges, in 1-2-5 sequence
x 10 (ten times) ± 5 % ( ± 8 % in 0 . 0 5 /xs-to-0.5 /is range)
± 3 % ( ± 5 % for x 10 magnification)
Continuously variable from NORM position in A s w e e p
Shifts B s w e e p trace continuously in vertical direction by 4 divisions or more with
Continuous delay (AFTER D E L A Y ) & triggered delay (B T R I G ' D: triggered by A trigger)
Continuous adjustable from 0 . 0 5 /xs/div to 0 . 5 s/div
12 kV
8 x 10 div (1 d i v = 10 mm)
1 Mfi ± 2 % , approx. 3 0 pF
3.5 ns (5 mV/div to 5 V/div)
1 7 . 5 ns (1 mV/div & 2 mV/div)
- 4 0 dB or less (at 1 kHz)
Single trace
Single trace
CH1 + ( ± C H 2 ) added display
Approx. 3 0 0 kHz
C H 1 : Y axis
C H 2 : X axis
Same as vertical axis (CH2)
Same as vertical axis (CH2)
DC to 1 MHz, within - 3 dB
5 Hz to 1 MHz, within - 3 dB
3 ° or less at 1 0 0 kHz
Same as vertical axis (CH2)
A s w e e p
Delayed s w e e p
X - Y oscilloscope operation
respect to A s w e e p
C S - 5 1 7 5