Prior To Operation; Chamfering Edges - DeWalt D26500 Original Instructions Manual

2. To remove the ejector, raise the lever
the ejector.
nOtE: The ejector must be used in combination with the dust
extraction adapter when connecting a vacuum extractor
For left-hand side shavings discharge (Fig. F), the ejector
must always be used.
1. Raise the lever 19 to open the spring-loaded closure
2. Push the ejector 18 into the left-hand side shavings
discharge outlet 3 until it clicks in place.
3. Release the lever.
4. To remove the ejector, raise the lever and pull out
the ejector.
Dust Extraction (Fig. G–I)

WARNING: When appropriate, connect a dust extraction
system designed in compliance with the applicable
directives regarding dust emission.
The tool is supplied with an adapter for connecting a dustbag or
a vacuum extractor. The dustbag is standard for K-models and
available as an option for all other models.
1. Fit the shavings ejector 18
2. Attach the dustbag 21 to the shavings ejector.
3. Alternatively, connect the tool to a vacuum extractor using
the adapter .
22
Assembling the Dustbag (Fig. I)
1. Assemble the dustbag by aligning the open ended slots
with the notches 25 and fitting the
bag 24 .
2. Turn the assembly clockwise to lock it in position.
3. Release the loops 52 to unfold the bag.
4. Fit the dustbag as described above.

Prior to Operation

• Adjust the depth of cut.
• If necessary, fit and adjust the parallel fence.
• If necessary, fit and adjust the rebating depth stop.
• Attach the shavings ejector.
• If necessary, connect the dust extraction.
• Use sharp cutting blades only.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
and pull out
19
20 .
into the outlet 3 as shown.
26
23 deflector onto the
Proper Hand Position (Fig. J)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the front handle
with the other hand on the main handle
Switching On and Off (Fig. A)

WARNING: Do not switch the tool on or off when the
cutters touch the workpiece or other materials.
For safety reasons the on/off switch
with a lock-off button 2 .
1. Press the lock-off button to unlock the tool.
2. To run the tool, press the on/off switch
on/off switch is released the lock-off switch is automatically
activated to prevent unintended starting of the machine.
Planing (Fig. A)
1. Switch the tool on.
2. Slowly move the tool over the workpiece.

WARNING:
• The feed speed should not be too high, especially
when using the maximum depth of cut and
planing width.
• Remember that several shallow cuts are better than
one deep cut.
• Always switch off the tool when work is finished and
before unplugging.
The tool is equipped with a parking shoe
off, the tool can be put down without waiting for the cutters to
come to a standstill.
Rebating
1. Fit and adjust the parallel fence.
2. Fit and adjust the rebating depth stop.
3. Proceed as for planing.

Chamfering Edges

The V-grooves in the nose piece of the shoe enable you to
chamfer edges.
Emptying the Dustbag (Fig. G–I)
The amount of shavings collected in the dustbag can be
determined from the transparent deflector.
1. Remove the dustbag 21 .
2. Remove the deflector
23
counterclockwise.
3. Empty the contents of the bag into a waste container.
4. Re-assemble the dustbag by aligning the open ended
slots 26 with the notches
the bag.
5. Turn the assembly clockwise to lock it in position.
6. Re-fit dustbag.
EngLIsh
20 .
of your tool is equipped
1
. As soon as the
1
6 . After switching
from the bag by turning it
24
25 and fitting the deflector onto
4 ,
23