Specifications - Toro REELMASTER 5500-D Operator's Manual

Specifications

Engine: Kubota three-cylinder, 4-cycle, liquid-
cooled diesel. 26kW (35 hp) @ governed to 3200
rpm; 1123 cc displacement. Heavy-duty, 3-stage,
remote-mounted air cleaner. High water
temperature shutdown switch.
Main Frame: All welded formed steel frame,
includes three tie-down loops
Cooling System: Radiator capacity is 7.1 l of 50/50
mixture of ethylene glycol anti-freeze. Remote
mounted 0.95L expansion tank. Removable oil
cooler/radiator intake screen. Air-to-oil cooler,
mounted to front of radiator, tips forward for
cleaning
Fuel System: Fuel tank capacity is 37.9 l (10 gal.)
of #2 diesel fuel. Equipped with a fuel filter/water
separator to capture water in the fuel.
Traction System: Foot pedal controls forward/
reverse ground speed. Ground speed: 0–16.1 kmh
(0–10 m.p.h.) forward and 0–6.4 kmh (0-4 mph)
reverse. Hydrostatic transmission mounted directly
on a 20.9:1 ratio front axle. Axle/reservoir capacity
is 4.7 l (5 qts). Replaceable filter mounted directly
on transmission housing. Model 03551—
Mechanical rear axle is coupled to the front axle by
a drive shaft and overrunning clutch.
Cutting Unit Drive System: Hydraulic reel motors
feature quick disconnects to ease removal/
installation on cutting units. Hydraulic fluid
reservoir capacity is 32.2 l (8.5 gal.). System
protected by a filter assembly with service indicator.
Seat: Deluxe high back seat with adjustable fore
and aft travel, weight and height. Tool box at the
left side of the seat.
Steering System: Power steering with dedicated
power source.
Tires: Two rear tires: 20 x 10-8, tubeless, 6-ply
rating. Two front tires: 26 x 12.00-12 tubeless, 4-
ply rating. Recommended tire pressure for the
front and rear tires is 69–103 kPa (10–15 psi).
Brakes: Individual drum-type wheel brakes on the
front traction wheels. Brakes are controlled by
individual pedals operated by the left foot.
Hydrostatic braking through the traction drive.
Electrical System: Automotive-type electrical
system. 12-volt, maintenance-free battery with 530
cold cranking Amps @ –17° C and 85 minute
reserve capacity @ 29° C. 40-amp alternator with
I.C. regulator/rectifier. Seat switch, reel and traction
interlock switches. An electronic controller
monitors and controls safety and operational
functions. Parking brake switch and individual
circuit backlap switches.
Controls: Foot-operated traction and brake pedals.
Hand-operated throttle, traction speed control lever,
parking brake lock, ignition switch with automatic
preheat cycle, single joy stick control for cutting
unit on/off and lift/lower. Cutting unit backlap
switch and reel speed controls located under the
operator seat.
Gauges: Hour meter, speedometer, fuel gauge,
temperature gauge. 4 warning lamps: oil pressure,
water temperature, amps and glow plug.
Diagnostics: The Automatic Control Electronics 7
ACE™ system allows precise timing and control of
machine functions for maximum reliability.
Optional hand-held diagnostic display connects to
an electronic control unit to pin point any electrical
problems quickly and easily. Available DATA
LOG™ system allows mechanic to find intermittent
problems.
General Specifications (approx.):
Width-of-Cut :
Overall Width:
Transport
Outside of front tires
Outside of rear tires
Overall Length:
Without grass baskets:
With grass baskets:
Height:
With Rollover protector:
Without
9
254 cm (100 in.)
222.5 cm (88 in.)
221 cm (87 in.)
133.3 cm (52.5)
287 cm (113 in.)
305 cm (120 in.)
208 cm (82 in.)
150 cm (59 in.)