Advertisement
Interface Description/ 接口说明
The color identifier of the alarm cable is subject to the actual pigtail label.
告警线缆颜色标识以实际的尾线标签为准。
NO.
Item
Description
序号
名称
说明
Indicates the analog video output interface is used only for debugging video output. The
1
VIDEO
interface supports only D1 video output.
模拟视频输出接口，仅用于调试视频输出。该接口仅支持以D1分辨率输出视频。
Indicates the power input interface. This interface supports 12 V DC (9.0 V to 15.0 V) and 24 V
2
POWER
AC (18.0 V to 29.9 V) power input.
电源输入接口。支持DC 12V（9.0V～15.0V）和AC 24V（18.0V～29.9V）电源输入。
Indicates the network interface used to connect to network cables.
Indicates the power over Ethernet (PoE) interface. When the power input interface and PoE
3
POE/LAN
interface are connected at the same time, PoE is preferred.
网络接口。连接网线。
PoE供电接口。当电源输入接口和PoE同时连接时，优先PoE供电。
Indicates the video input/output interface. To ensure audio output quality, connect a 3.5 mm
AUDIO IN/
4
TRS connector to the interface.
AUDIO OUT
音频输入输出接口。为保证音频输出质量，请使用三段式3.5mm音频接头。
Indicates the ground interface.
5
GND
接地接口。
Indicates the RS485 interface that enables the camera and the connected device to send data
RS485+/
6
to each other in half-duplex mode through the transparent channel.
RS485-
RS485接口。通过该接口，摄像机可以以半双工的方式通过透明通道与连接的设备互相传递数据。
ALARM_OUTn Indicates the alarm output interface. The value n can be 1 and 2. ALM_OUTn and ALM_REFn
form a group of alarm output. There are two groups of alarm output.
ALARM_REFn
告警输出接口，n为1和2。ALM_OUTn和ALM_REFn组成一组告警输出，一共2组。
Indicates the alarm input interface. The value m can be 1 and 2. ALM_INm and GND form a
7
ALARM_INm
group of alarm input. There are two groups of alarm input.
告警输入接口，m为1和2。ALM_INm和GND组成一组告警输入，一共2组。
Indicates the alarm input ground interface.
GND
告警输入接地接口。
1
2
3
4
5
6
7
NOTE/ 说明
Reset Button and SD Card Slot/Reset 键和 SD 卡槽
1
2
NO.
Description
序号
说明
Reset button. To restart the device, hold down the RST button for less than 3s. To
restore the device to factory defaults, hold down the RST button for at least 3s
during the device running or hold down the RST button, power on the device, and
1
keep holding down the RST button for more than 5s.
重置按钮。运行时按住RST键短于3秒重启设备；运行时按住RST键不短于3秒或者按住RST
键后上电并持续按住RST键不短于5秒后恢复出厂配置。
SD card slot that supports only Micro SD cards of Class 6 or higher classes. You
can replace a Micro SD card only when the device is powered off. When a Micro SD
card is used for the first time, log in to the web page of the device and format the
2
Micro SD card. For details, see Configuration Guide.
SD卡卡槽，仅支持Micro SD卡（Class 6及以上）。请在设备断电的情况下插拔SD卡，否
则会造成系统异常。首次使用时，请登录设备Web客户端，格式化SD卡，操作方法请参见
《配置指南》。
Ventilation valve used to ensure ventilation inside and outside the device. Do not
3
remove the ventilation valve.
透气阀。用于设备内外空气流通，请勿拆卸。
Prepare for Installation Tools/ 准备安装工具
Hammer drill (for mounting a camera
Video surveillance tester
视频监控测试仪
冲击钻（吊顶和墙壁安装时使用）
Measuring tape
钢卷尺
Claw hammer (for mounting a camera
on the ceiling or wall)
RJ-45 connector crimping tool
羊角锤（吊顶和墙壁安装时使用）
Utility knife
裁纸刀
3
Operation
操作
Use the Phillips screwdriver
to remove the camera
bottom cover. Then, you
can see the Reset button
and SD card slot.
使用十字螺丝刀将摄像机底
盖卸下，即可看到重置键和
SD 卡槽。
on the ceiling or wall)
PVC insulation tape
绝缘胶带
Cable stripper
Waterproof tape
剥线钳
防水胶带
Phillips screwdriver (Head model: 1#
and 2#.)
水晶头压线钳
十字螺丝刀（刀头型号为：1#和2#）
Glass cement
Wiring terminal
玻璃胶
接线端子
Advertisement
