Peripheral Only Card (Imp2B-Xxxxb); Table 4-3 J2 Pinout (Peripheral Only) - GE IMP2B Hardware Reference Manual

4.1.2 Peripheral Only Card (IMP2B-xxxxB)

Table 4-3 J2 Pinout (Peripheral Only)

Pin
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Non I/O signals (in grey above) are described in more detail in the PowerPact3
Family Product Manual.
Key
44 IMP2B 3U cPCI Single Board Computer
Row A Row B
GA4 GA3
Unused GND
Unused GND
GND GND
ETH0_1+ ETH0_3+/1_1+
ETH0_1- ETH0_3-/1_1-
ETH0_0+ ETH0_2+/1_0+
ETH0_0- ETH0_2-/1_0-
USB2_2- USB2_2+
J14-2 J14-1
J14-4 J14-3
J14-10 J14-14
J14-12 J14-16
J14-22 J14-21
J14-24 J14-23
J14-30 J14-34
J14-32 J14-36
J14-49 J14-42
J14-51 J14-44
J14-50 J14-54
J14-52 J14-56
No Connection J14-62
LINK
PowerPact3 Family Product Manual, publication number
PMC rear I/O signals (see the PMC Rear I/O Tracking
Ethernet channel 0 (10/100BaseT)
Ethernet channel 1 (10/100BaseT) or Ethernet channel 0 (10/100/1000BaseT)
General purpose I/O (4 bits)
COM1 (RS232)
COM2 (RS232/RS422)
USB2.0 Port 1
USB2.0 Port 2
CAUTION
If an IMP2B is configured for Gigabit Ethernet and is connected to another Gigabit Ethernet capable
device, the CPCI3UX605 (if used) must be configured to allow the port to be fully connected. Failure to
do so will prevent the Ethernet port from functioning correctly.
CAUTION
Do not install an IMP2B built in 'Peripheral Only' mode into a Rack Host cPCI slot.
Row C Row D
GA2 GA1
USB2_1+ COM2_RX_B
USB2_1- COM2_RX_A
GPIO1 COM2_TX_B
GPIO0 COM2_TX_A
PRST# Unused
DEG# GND
FAL# Unused
USB2_2_PWR GPIO2
J14-6 J14-5
J14-8 J14-7
J14-13 J14-18
J14-15 J14-20
J14-26 J14-25
J14-28 J14-27
J14-33 J14-38
J14-35 J14-40
J14-41 J14-46
J14-43 J14-48
J14-53 J14-58
J14-55 J14-60
J14-64 J14-61
PP3-0HH.
section)
Row E Row F
GA0 GND
COM1_RX_B GND
COM1_RX_A GND
COM1_TX_B GND
COM1_TX_A GND
Unused GND
USB2_1_PWR GND
Unused GND
GPIO3 GND
J14-9 GND
J14-11 GND
J14-17 GND
J14-19 GND
J14-29 GND
J14-31 GND
J14-37 GND
J14-39 GND
J14-45 GND
J14-47 GND
J14-57 GND
J14-59 GND
J14-63 GND
Publication No. IMP2B-0HH/5