Troubleshooting; Replacements Parts - DeWalt 55RI6HN Instruction Manual

English
PRODUCT CARE, cont'd
Mower Tracking
If your mower tracks to the left or right, a
tracking adjustment is needed.
To adjust the tracking, use the tracking
knob on the back of the mower and
follow these instructions:
1. If the mower tracks (pulls) to the right,
rotate the tracking knob to the left in
1/4-turn increments until the mower
tracks straight. See Figure 30. Turn left
to go left.
2. If the mower tracks (pulls) to the left,
rotate the tracking knob to the right
in 1/4-turn increments until the mower tracks straight. See Figure 30. Turn right to
go right.

Troubleshooting

Problem
Excessive vibration
Uneven cut
Mower will not mulch grass
Mower creeping
Mower drifting
Engine fails to start

Replacements Parts

Part number Packaged Part number
954-05814 DXgX501102
954-05812 DXgZ501103
742P05534 DXgX110208
02005017-X
742P04417-l
742P04278A-X
618-07406
734-04155
731-11926
751-15884
946-05434
946-05341B
Attachments/Accessories
Part number Description
59A50013038
Grass Collector
19B70064000
Mulch Kit, 48"
14
Figure 30
Cause
1. Cutting blade loose or unbalanced.
2. Damaged or bent cutting blade.
1. Deck not properly leveled.
2. Cutting blade dull or damaged.
3. Uneven tire pressure.
1. Engine speed too low.
2. Wet grass.
3. Excessively high grass.
4. Dull blade.
1. Neutral control linkage needs adjusted.
1. Mower tracking needs adjusted.
1. PTO/Blade engaged.
2. Blown fuse.
3. Parking brake not engaged.
Description
Deck Belt
Drive Belt
Hi-Lift Blade, 17.0
XTREME® Medium-Lift Blade
Sand Blade
XTREME® Mulching Blade
Deck Spindle
Deck Wheel
Deck Skid Guard
Gas Cap
Throttle Control Cable
Choke Control
Part number
59B50005000
LED Light Kit
59A50007000
Mesh Storage Bag
1. Tighten blade and spindle.
2. Replace blade.
1. Perform side-to-side deck adjustment.
2. Sharpen or replace cutting blade.
3. Check and correct tire pressure in the rear tires.
1. Place throttle in FAST (rabbit) position.
2. Do not mulch when grass is wet.
3. Mow once at a high cutting height, then mow again at desired
height or make a narrower cutting swath.
4. Sharpen or replace blade.
1. Adjust neutral control linkage.
1. Adjust mower tracking.
1. Place blade engage lever in disengaged (OFF) position.
2. Replace fuse(s). See Engine Operator's Manual.
3. Engage parking brake.
Part number Packaged Part number
925-06908
946-05420B
946-05421B
931-08120
634-07608
634-07607
KM-11013-0752
KM-11013-0746 490-201-M022
KM-49019-0027 DXgX2400002
KM-49065-0721 490-201-M007
KM-BPR4Es F4RTC - DXgX250034
Description Part number
59A50008000
59A50009000
Remedy
Description
Ignition Key
Park Brake Cable, Left
Park Brake Cable, Right
Chute Assembly
Rear Wheel Assembly, 20 x 10-8
Front Wheel Assembly, 11 x 4-5
Air Filter
Pre-Filter
Fuel Filter
Oil Filter
Spark Plug
Description
Single-Wheel Sulky
Dual Wheel Sulky