Mitsubishi Electric LGH-50RVS-E Installation Instructions Manual page 23

No.38
CO concentration display setting
2
Set to display CO concentration when the CO
2
components is used.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 38
- -
- This function is available only when "Sensor value" is set to "Yes"
(Display) by the remote controller PZ-62DR-E.
- When displaying CO concentration, supply air temperature cannot
2
be displayed simultaneously.
- CO concentration display shows the value detected by a CO
2
sensor connected to Lossnay unit. The value may differ from the
actual indoor CO concentration. This function cannot be used as a
2
measuring instrument.
- The value may significantly differ from the actual indoor CO
concentration for approx. 15 minutes after starting operation.
Calculated supply air temperature display
No.39
setting
Set to display calculated supply air temperature or not.
This function is N/A from Lossnay unit DIP-SW.
In addition, this function is available only when "Sensor value" is set
to "Yes"(Display) by the remote controller PZ-62DR-E.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 39
- -
Temperature exchange efficiency
No.40, 41
setting
Set the 10 digit of temperature exchange efficiency which is used to
calculate supply air temperature.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
N/A 40
- -
- -
- -
- -
- -
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
N/A 41
- -
- -
- -
- -
- -
sensor of the system
2
Setting CO concentration
2
check display
0 N/A
Available on the screen
1
(Factory setting)
of PZ-62DR-E
2
Setting Calculated supply air
check temperature display
0
N/A
(Factory setting)
Available on the screen
1
of PZ-62DR-E
Setting 10 digit of temperature
check exchange efficiency
0 0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8
8
(Factory setting)
9 9
Setting 1 digit of temperature
check exchange efficiency
0 0
1 1
2
2
(Factory setting)
3 3
4 4
5 5
6 6
7 7
8 8
9 9
No.42
Outdoor temperature correction
Set the correction for the outdoor temperature displayed on the
PZ-62DR-E screen by function
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
SW No. Setting
-
-
-
-
-
-
-
2
N/A -
-
-
-
-
-
-
-
No.43
Indoor temperature correction
Set the correction for the indoor temperature displayed on the
PZ-62DR-E screen by function
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
SW No. Setting
-
-
-
-
-
-
-
N/A -
-
-
-
-
-
-
-
No.44
CO
2
CO concentration displayed on the PZ-62DR-E can be corrected.
2
This function is available when there is CO
the location of CO
2
DIP-SW
Setting
check
SW No. Setting
-
-
-
-
-
N/A -
-
-
-
-
-
Eng-23
.
No. 36
PZ-62DR-E
Setting The correction to
check thermistor detection
Function No. Setting Data
- 0 -7˚C
- 1 -6˚C
- 2 -5˚C
- 3 -4˚C
- 4 -3˚C
- 5 -2˚C
- 6 -1˚C
7
- 42 0˚C
(Factory setting)
- 8 +1˚C
- 9 +2˚C
- 10 +3˚C
- 11 +4˚C
- 12 +5˚C
- 13 +6˚C
- 14 +7˚C
.
No. 37
PZ-62DR-E
Setting The correction to
check thermistor detection
Function No. Setting Data
- 0 -7˚C
- 1 -6˚C
- 2 -5˚C
- 3 -4˚C
- 4 -3˚C
- 5 -2˚C
- 6 -1˚C
7
- 43 0˚C
(Factory setting)
- 8 +1˚C
- 9 +2˚C
- 10 +3˚C
- 11 +4˚C
- 12 +5˚C
- 13 +6˚C
- 14 +7˚C
concentration correction
concentration gap due to
2
sensor.
PZ-62DR-E
Setting CO
check correction
Function No. Setting Data
- 0 -500 ppm
- 1 -400 ppm
- 2 -300 ppm
- 3 -200 ppm
- 4 -100 ppm
5
- 44 ±0 ppm
(Factory setting)
- 6 100 ppm
- 7 200 ppm
- 8 300 ppm
- 9 400 ppm
- 10 500 ppm
concentration
2