Ruckus Wireless R320 Quick Setup Manual

R320 Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions on how
to set up your Ruckus R320 access point. After completing the
steps in this guide, you will be able to place the access point (AP)
at your site and provide network access to wireless clients.
NOTE: Please read these operation instructions carefully before
start of operation.
NOTE: The minimum software revision for the R320 is
ZoneDirector (ZD) 10.2.1 native or later, SmartZone (SZ) 5.1
new AP model or later, or Unleashed 200.7 or later.
FIGURE 1 R320 Top
Before You Begin
Before deploying Ruckus products, please check for the latest
software and the release documentation.
• Release Notes and other user documentation are available at
http://support.ruckuswireless.com/documents.
• Software upgrades are available at http://
support.ruckuswireless.com/software.
This Guide in Other Languages
• 请从以下网站获得该指南的简体中文版 https://
support.ruckuswireless.com.
• Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com.
• このガイドの日本語版は https://support.ruckuswireless.com
ご覧ください。
• 이 가이드의 한국어 버전은 웹 사이트 (https://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
• Veja a versão em português (Brasil) deste guia em
support.ruckuswireless.com.
Copyright © 2019 CommScope, Inc. All rights reserved.
Published November 2019, Part Number 800-71895-001 Rev C
• Puede ver la versión en español (América Latina) de esta guía
en https://support.ruckuswireless.com.
Package Contents
A complete R320 installation package includes all of the items
listed below:
• R320 Access Point
• One wall-mount anchor kit, including two 1" No. 8 steel pan
head Phillips sheet metal screws and wall-mount anchors.
• One external T-bar bracket (two unassembled parts)
• One unit removal pin
• Service Level Agreement/Limited Warranty Statement
• Declaration of Conformity
• Regulatory Statement
• Ruckus AP Getting Started Guide
• AP Cloud Management Insert
• This Quick Setup Guide
CONFIGURING THE AP
Step 1: Collecting the AP MAC Address
• Write down the MAC address (12 alphanumeric digits) from the
outside of the AP.
NOTE: If the AP is to be managed by a Ruckus controller, then
follow the controller user documents to connect the AP to
your local network and configure it for initial operation. In that
case, you may not need to complete the following steps.
Step 2: Collecting Setup Requirements,
Hardware, and Tools
• A computer with Ethernet adapter running Windows 7 or
equivalent, with Firefox or equivalent web browser.
• One Cat 5e (or better) Ethernet cable.
• An AC-to-12VDC power adapter (sold separately)
--OR--
an 802.3af-compliant Power over Ethernet (PoE) switch or PoE
injector.
Step 3: Connecting Your Computer to the AP
1. After removing the AP from its package, place it next to your
computer.
2. Using an Ethernet cable, connect your computer's network
port to the POE IN port on the AP.
3. Connect the AC power adapter (sold separately) to the
12VDC AP port, and plug the AC power adapter into a
convenient and protected AC power source.
Alternatively, connect the POE IN port to a PoE injector or
PoE switch for both power and network connectivity.
で
https://
FIGURE 2 AP Rear Panel
4. After bootup, verify that the PWR LED on the AP is a steady
green.
Step 4: Preparing Your Computer for AP Setup
NOTE: The following procedures assume that Windows 7 is the
operating system. Procedures for other operating systems are
similar.
1. On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as follows:
• Start > Control Panel > Network and Sharing Center >
Change Adapter Settings
2. Edit the TCP/IPv4 address settings as follows:
• Local Area Connection > Properties > Internet Protocol
Version 4 (TCP/IPv4) > Properties
The Internet Protocol Version 4 (TCP/IPv4) Properties dialog
box appears.
NOTE: Write down all of the currently active settings so
you can restore your computer to its current
configuration when this procedure is completed.
3. Select Use the following IP address (if it is not already
selected) and then make the following entries:
• IP address: 192.168.0.22 (or any available address in the
192.168.0.x network, except 192.168.0.1, which is the
default used by the R320 AP)
• Subnet mask: 255.255.255.0
• Leave the DNS server and Default gateway fields empty.
4. Click OK to save your changes. Your changes are put into
effect immediately.
Page 1 of 4