Mitsubishi Electric 700 Series Installation Manualline page 24

Pr. Name
503 Maintenance timer
Maintenance timer alarm
504
output set time
USB communication station
547
number
USB communication check
548
time interval
549 Protocol selection
NET mode operation
550
command source selection
PU mode operation command
551
source selection
555 Current average time
556 Data output mask time
Current average value monitor
557
signal output reference current
Energization time carrying-
563
over times
Operating time carrying-over
564
times
571 Holding time at a start
611 Acceleration time at a restart
645 AM 0V adjustment
653 Speed smoothing control
Regeneration avoidance
665
frequency gain
800 Control method selection
859 Torque current
Input phase loss protection
872
∗7
selection
Regeneration avoidance
882
operation selection
Regeneration avoidance
883
operation level
Regeneration avoidance
885 compensation frequency limit
value
Regeneration avoidance
886
voltage gain
888 Free parameter 1
889 Free parameter 2
C1
AM terminal calibration
(901)
∗5
C2
Terminal 2 frequency setting
(902)
bias frequency
∗5
C3
Terminal 2 frequency setting
(902)
bias
∗5
125
Terminal 2 frequency setting
(903)
gain frequency
∗5
C4
Terminal 2 frequency setting
(903)
gain
∗5
Initial
Setting Range
Value
0 (1 to 9998) 0
0 to 9998, 9999 9999
0 to 31 0
0 to 999.8s,
9999
9999
0, 1 0
0, 2, 9999 9999
2 to 4, 9999 9999
0.1 to 1.0s 1s
0 to 20s 0s
Rated
0 to 500A inverter
current
(0 to 65535) 0
(0 to 65535) 0
0 to 10s, 9999 9999
0 to 3600s, 9999 9999
970 to 1200 1000
0 to 200% 0
0 to 200% 100
20, 30 20
0 to 500A (0 to
9999
****), 9999
∗4
0, 1 1
0, 1, 2 0
400VDC/
300 to 800V
780VDC
∗6
0 to 10Hz, 9999 6Hz
0 to 200% 100%
0 to 9999 9999
0 to 9999 9999
- -
0 to 400Hz 0Hz
0 to 300% 0%
0 to 400Hz 60Hz
0 to 300% 100%
Pr. Name
C5
Terminal 4 frequency setting
(904)
bias frequency
∗5
C6
Terminal 4 frequency setting
(904)
bias
∗5
126
Terminal 4 frequency setting
(905)
gain frequency
∗5
C7
Terminal 4 frequency setting
(905)
gain
∗5
C22
(922)
∗5
C23
(922)
∗5
Parameter for manufacturer setting. Do not set.
C24
(923)
∗5
C25
(923)
∗5
990 PU buzzer control
991 PU contrast adjustment
Pr.CL Parameter clear
ALLC All parameter clear
Er.CL Faults history clear
Pr.CH Initial value change list
∗1
Differ according to capacities.
6%: FR-E720-050(SC) or less, FR-E740-026(SC) or less,
FR-E720S-050 or less, FR-E710W-050 or less
4%: FR-E720-080(SC) to175(SC), FR-E740-040(SC) to 095(SC),
FR-E720S-080 and 110
3%: FR-E720-240(SC) and 330(SC), FR-E740-120(SC) and 170(SC)
2%: FR-E720-470(SC) and 600(SC), FR-E740-230(SC) and 300(SC)
∗2
Differ according to capacities.
5s: FR-E720-175(SC) or less, FR-E740-095(SC) or less,
FR-E720S-008 to 110, FR-E710W-050 or less
10s: FR-E720-240(SC) and 330(SC), FR-E740-120(SC) and 170(SC)
15s: FR-E720-470(SC) and 600(SC), FR-E740-230(SC) and 300(SC)
∗3
Differ according to capacities.
6%: FR-E720-008(SC) and 015(SC), FR-E720S-008 and 015,
FR-E710W-008 and 015
4%: FR-E720-030(SC) to 330(SC), FR-E740-016(SC) to 170(SC),
FR-E720S-030 to 110, FR-E710W-030 and 050
2%: FR-E720-470(SC) and 600(SC), FR-E740-230(SC) and 300(SC)
∗4
The range differs according to the Pr. 71 setting.
∗5
The parameter number in parentheses is the one for use with the
operation panel (FR-PA02) for the FR-E500 series or parameter unit
(FR-PU04/FR-PU07).
∗6
The initial value differs according to the voltage class. (100V, 200V class/
400V class)
∗7
Available only for the three-phase power input specification model.
∗8
For the safety stop function model, this setting is active only during the
communication operation.
∗9
Theses parameters can be set only in the safety stop function model.
PARAMETER LIST
Initial
Setting Range
Value
0 to 400Hz 0Hz
0 to 300% 20%
0 to 400Hz 60Hz
0 to 300% 100%
0, 1
0 to 63
0, 1
0, 1
0, 1
—
1
58
0
0
0
—
21