Appendix; Specifications - Yamaha MG10/2 Owner's Manual

Specifications
I General Specifications
Frequency Characteristics (ST OUT)
Total Harmonic Distortion (ST OUT)
1
Hum and Noise
2
Maximum Voltage Gain
Monaural/Stereo Input Gain Control
Monaural/Stereo High Pass Filter
Crosstalk (1 kHz)
Monaural/Stereo Input Channel Equalization:
3
Max. Variation
Monaural/Stereo Input Peak Indicator
Level Meters
Phantom +48 VDC Power (Balanced input)
Included Accessory
Option
Power Supply
Power Consumption
× ×
Max. Dimensions (W H D)
Weight
Where 0 dBu = 0.775 V and 0 dBV = 1 V
1
Measured with 12.7 kHz, –6 dB/oct. low pass filter (equivalent to 20 kHz, –∞ filter).
(CH MIC INPUT to ST, AUX, EFFECT SEND)
2
Turning PAN/BAL to left or right.
3
Shelving turnover/rolloff frequency: 3 dB before maximum cut or boost.

Appendix

20 Hz–20 kHz +1 dB, –3 dB @+4 dBu, 10 k
0.1 % (THD+N) @+14 dBu, 20 Hz–20 kHz, 10 k
(CHs 1 and 2)
–128 dBu
–100 dBu
–87 dBu (91 dB S/N)
–85 dBu (89 dB S/N)
–64 dBu (68 dB S/N)
→
60 dB CH MIC INPUT CH INSERT OUT
→
76 dB CH MIC INPUT ST OUT
→
64.2 dB CH MIC INPUT REC OUT
→
70 dB CH MIC INPUT AUX SEND1 (PRE)
→
76 dB CH MIC INPUT AUX SEND2 (POST)
→
76 dB ST CH MIC INPUT ST OUT
→
50 dB ST CH LINE INPUT ST OUT
→
41 dB ST CH LINE INPUT AUX SEND1 (PRE)
→
47 dB ST CH LINE INPUT AUX SEND2 (POST)
→
26 dB ST CH INPUT ST OUT
→
12 dB AUX RETURN ST OUT
→
23.8 dB 2TR INPUT ST OUT
44 dB variable
80 Hz 12 dB/octave
–70 dB between input channels
–70 dB between input/output channels (CHs 1 to 6)
±15 dB
HIGH 10 kHz shelving
MID 2.5 kHz peaking
LOW 100 Hz shelving
On each channel: red indicator lights if post-EQ signal (on ST channels, if either post-EQ sig-
nal or post-mic-amp signal) comes within 3 dB of the clipping level.
Two 12-point LED meters [Stereo (L, R)]
Peak point: red indicator
+5, +3, +1, and 0 points: yellow indicators
–1, –3, –5, –7, –10, –15, –20: green indicators
Supplied when Phantom +48 V switch is ON.
Power adaptor (PA-10)
Microphone-stand adaptor (BMS-10A)
USA and Canada: 120 V AC, 60 Hz
Europe: 230 V AC, 50 Hz
Australia: 240 V AC, 50 Hz
Korea: 220 V AC, 60 Hz
19 W
× ×
251 65 290.5 mm
1.8 kg
Ω
(with gain control at minimum level)
Ω
(with gain control at maximum level)
Equivalent input noise (CHs 1 and 2)
Residual output noise (ST OUT)
ST, Master fader at nominal level and all Ch at minimum
level.
All channel AUX controls at minimum level.
ST, Master fader and one Ch fader at nominal level.
(CHs 1 and 2)
MG10/2
23