Table of Contents
Advertisement
6.
Torque the ROPS pivot bolt
113 N∙m (67 to 83 ft-lb) to avoid any bouncing of
the roll bar and sunshade.
7.
On each side of the sunshade frame, loosely
mount a brace to the brace bracket as follows:
•
For Models 03820, 03821, 30604, 30605,
30608, and 30609 on each side of the
sunshade frame, loosely mount a brace to
the rear hole of the brace bracket with a
bolt (1/2 x 2-1/2 inches), washer (1/2 inch)
washer, and flange nut (1/2 inch) as shown
in
Figure
20.
•
For Models 30446, 30446N, 30447, and
30447N, on each side of the sunshade
frame, loosely mount a brace to the second
hole of the brace bracket with a bolt (1/2 x
2-1/2 inches), washer (1/2 inch), and flange
nut (1/2 inch) as shown in
Figure 20
Models 03820, 03821, 30604, 30605, 30608, and 30609
1. Bolt (1/2 x 2-1/2 inches)
2. Washer (1/2 inch)
3. Brace
4. Front hole
5. Flange nut (1/2 inch)
Figure 21
Models 30446, 30446N, 30447, and 30447N
1. Bolt (1/2 x 2-1/2 inches)
2. Washer (1/2 inch)
3. Brace
4. Front hole
5. Flange nut (1/2 inch)
8.
Loosely install a brace bracket to each brace
with a bolt (1/2 x 2-1/2 inches), washer (1/2
inch), and flange nut (1/2 inch) as shown in
Figure
20.
9.
Position the ROPS-mounting brackets onto
the top of the traction unit roll bar
(Figure
19) 91 to
Figure
21.
g020028
6. Second hole
7. Third hole
8. Rear hole
9. Brace bracket
g020206
6. Second hole
7. Third hole
8. Rear hole
9. Brace bracket
(Figure
22).
Make sure that the roll bar is centered in the
ROPS-mounting brackets.
1. ROPS-mounting bracket
2. Roll bar post
3. U-bolt (4 inches)
10.
Using the mounting holes shown in
ROPS-mounting brackets to the top of the roll
bar with 2 U-bolts (2-3/4 inch) and 4 flange nuts.
11.
Using the mounting holes shown in
loosely secure each of the brace brackets to
the roll bar posts with a U-bolt (4 inches) and
2 flange nuts.
12.
Move the brace bracket up or down, on the
vertical roll bar posts, until the sunshade frame
is level to the floor.
Note:
Use a level to make sure that the frame
is level to the ground.
Note:
Use the front mounting holes in the brace
bracket, if you need more adjustability.
13.
Tighten the U-bolt flange nuts, securing the
mounting brackets to the posts.
14.
Tighten all the remaining flange nuts as follows:
•
Torque the flange nuts (3/8 inch) 41 to 55
N∙m (34 to 41 ft-lb).
•
Torque the flange nuts (1/2 inch) 113 to 141
N∙m (84 to 104 ft-lb).
15.
Remove the flange-head bolts securing the
frame-alignment bar to the frame and remove
the alignment bar.
16.
While aligning the mounting holes, position the
sunshade onto the frame as shown in
13
Figure 22
4. Flange nut (3/8 inch)
5. U-bolt (2-3/4 inch)
Figure
Figure
Figure
g019766
22,
22,
23.
Advertisement
Table of Contents
