Table of Contents
Advertisement
Quick Links
White or Red Universal Sunshade
Groundsmaster
Model No. 30349
Model No. 30552
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical
or chemicals known to the State of
California to cause cancer, birth defects,
or reproductive harm.
Safety
General
Although hazard control and accident prevention
partially depend on the design and configuration of the
machine, these factors also depend on the awareness,
concern, and proper training of the personnel involved
in the operation, transport, maintenance, and storage
of the machine. Improperly using or maintaining the
machine can result in injury or death. To reduce the
potential for injury or death, comply with the following
safety instructions.
Before Operating
1.
Review and understand the contents of the
Installation Instructions before installing the
sunshade.
2.
Keep all shields, safety devices and decals
in place. If a shield, safety device or decal
is defective, illegible, or damaged, repair or
replace it before operating the machine.
3.
Do not weld, cut, drill, modify, or remove the roll
bar in any matter.
4.
Tighten any loose nuts, bolts, or screws to
ensure that the machine is in safe operating
condition.
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
and Reelmaster
While Operating
Maintenance and Service
Register at www.Toro.com.
®
Traction Units
1.
Use extreme care when working close to fences,
ditches, or on hillsides.
2.
Check carefully for overhead clearances (i.e.,
branches, doorways, electrical wires) before
driving under any objects and do not contact
them.
3.
Tie down the sunshade frame when transporting
the machine.
4.
Wear hearing protection when operating any
machine with a sunshade.
1.
Before servicing or making adjustments, lower
the implement, shut off the engine, engage the
parking brake, and remove the key.
2.
Make sure that the machine is in safe operating
condition by keeping all nuts, bolts, and screws
tight.
3.
When working on the sunshade installation,
wear eye protection.
4.
Replace a damaged sunshade. Do not repair
or revise.
5.
When installing the sunshade or performing
service, use correct supports, hoists, and jacks.
If the sunshade is not properly supported, it may
move or fall, which may result in personal injury.
6.
To ensure optimum performance and safety,
always purchase genuine Toro replacement
parts and accessories. Replacement parts and
accessories made by other manufacturers could
be dangerous. Such use could void the product
warranty of The Toro Company.
Original Instructions (EN)
All Rights Reserved *3408-251* D
Printed in the USA
Form No. 3408-251 Rev D
Installation Instructions
Advertisement
Table of Contents
Summary of Contents for Toro 30349
- Page 1 Keep all shields, safety devices and decals To ensure optimum performance and safety, in place. If a shield, safety device or decal always purchase genuine Toro replacement is defective, illegible, or damaged, repair or parts and accessories. Replacement parts and replace it before operating the machine.
-
Page 2: Table Of Contents
Safety and Instructional Decals Safety and instruction decals are affixed to your decal98-4387 sunshade. If any decal becomes illegible or damaged, 98-4387 install a new decal. 1. Warning—wear hearing protection. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty. -
Page 3: Frame Assembly
Description Qty. Bolt (3/4 x 4 inches) Nut (3/4 inch) Washer (13/16 x 1-1/2 inches) Frame assembly Left ROPS-mounting bracket Right ROPS-mounting bracket Brace Left brace bracket Right brace bracket Install the sunshade on the Groundsmaster 360 or 7200 Bolt (1/2 x 2-1/2 inches) machines. - Page 4 Description Qty. Bolt (3/4 x 4 inches) Nut (3/4 inch) Washer (13/16 x 1-1/2 inches) Frame assembly Left ROPS-mounting bracket Right ROPS-mounting bracket Left ROPS-mounting bracket (from kit 136-1830) Right ROPS-mounting bracket (from kit 136-1830) Brace Left brace bracket Right brace bracket Install the sunshade on the Groundsmaster 4500 and 4700 Bolt (1/2 x 2-1/2 inches) machines or Reelmaster 6700 and 7000 machines.
- Page 5 Description Qty. Frame assembly Left ROPS-mounting bracket Right ROPS-mounting bracket Brace Left brace bracket Right brace bracket Bolt (1/2 x 2-1/2 inches) Large washer Install the sunshade on the Reelmaster 3100 and 3550 machines or Groundsmaster 3500 and 3505 machines. Flange nut (1/2 inch) U-bolt (2-3/4 inch) Flange nut (3/8 inch)
-
Page 6: Bolt (1/2 X 2-1/2 Inches)
Installing the Sunshade Position the ROPS-mounting brackets onto the top of the traction unit roll bar (Figure Groundsmaster 5900 Machine Note: Make sure that the roll bar is centered in the mounting brackets. To properly align the frame, attach the frame-alignment bar to the mounting tabs on the rear of the sunshade frame with 2 flange-head bolts (5/16 x 1-1/4 inches) as shown in... -
Page 7: Sunshade
Installing the Sunshade While aligning the mounting holes, position the sunshade onto the frame as shown in Figure Groundsmaster 3280 Machine To properly align the frame, attach the frame-alignment bar to the mounting tabs on the rear of the sunshade frame with 2 flange-head bolts (5/16 x 1-1/4 inches) as shown in Figure g017923... -
Page 8: Bolt (3/4 X 4 Inches)
Insert a washer (13/16 x 1-1/2 inches) onto each Position the ROPS-mounting brackets onto the bolt (3/4 x 4 inches) as shown in Figure top of the traction unit roll bar (Figure Note: Make sure that the roll bar is centered in the ROPS-mounting brackets. - Page 9 Installing the Sunshade While aligning the mounting holes, position the sunshade onto the frame as shown in Figure Groundsmaster 360 or 7200 Machines To properly align the frame, attach the frame-alignment bar to the mounting tabs on the rear of the sunshade frame with 2 flange-head bolts (5/16 x 1-1/4 inches) as shown in Figure g020025...
- Page 10 Torque the ROPS pivot bolt (Figure 13) 91 to 113 N∙m (67 to 83 ft-lb) to avoid any bouncing of the roll bar and sunshade. On each side of the sunshade frame, loosely mount a brace to the second hole of the brace bracket with a bolt (1/2 x 2-1/2 inches), washer (1/2 inch), and flange nut (1/2 inch) as shown Figure...
- Page 11 Using the mounting holes shown in Figure 1-1/4 inches) and 2 small washers (Figure 16). loosely secure each of the brace brackets to Position a washer on each side of the sunshade the roll bar posts with a U-bolt (2-3/4 inch) and rubber grommet.
- Page 12 Installing the Sunshade Groundsmaster 4000 Machine or Reelmaster 3555 and 3575 Machines To properly align the frame, attach the frame-alignment bar to the mounting tabs on the rear of the sunshade frame with 2 flange-head bolts (5/16 x 1-1/4 inches) as shown in Figure g020023 Figure 18...
- Page 13 Torque the ROPS pivot bolt (Figure 19) 91 to Make sure that the roll bar is centered in the 113 N∙m (67 to 83 ft-lb) to avoid any bouncing of ROPS-mounting brackets. the roll bar and sunshade. On each side of the sunshade frame, loosely mount a brace to the brace bracket as follows: •...
- Page 14 Installing the Sunshade Groundsmaster 4500 and 4700 Machines or Reelmaster 6700 and 7000 Machines Important: Installation kit (Part No. 136-1830) is required for Groundsmaster 4500 and 4700 with serial number 400000001 and higher. To properly align the frame, attach the frame-alignment bar to the mounting tabs on the rear of the sunshade frame with 2 flange-head bolts (5/16 x 1-1/4 inches) as shown in...
- Page 15 g020206 Figure 27 1. Bolt (1/2 x 2-1/2 inches) 6. Second hole 2. Washer (1/2 inch) 7. Third hole 3. Brace 8. Rear hole 4. Front hole 9. Brace bracket 5. Flange nut (1/2 inch) g215450 Figure 25 Loosely install a brace bracket to each brace with a bolt (1/2 x 2-1/2 inches), washer (1/2 1.
- Page 16 Using the mounting holes shown in Figure loosely secure each of the brace brackets to the roll bar posts with a U-bolt (4 inches) and 2 flange nuts. Note: Use the U-bolt (4-1/2 x 3 inches) from the installation kit (Part No. 136-1830) for Groundsmaster 4500 and 4700 machines with serial number 400000001 and higher.
- Page 17 Installing the Sunshade Position the ROPS-mounting brackets onto the top of the traction unit roll bar (Figure 32). Make sure that the roll bar is centered in the Reelmaster 5010 Machine or ROPS-mounting brackets. Groundsmaster 4300 Machine To properly align the frame, attach the frame-alignment bar to the mounting tabs on the rear of the sunshade frame with 2 flange-head bolts (5/16 x 1-1/4 inches) as shown in...
- Page 18 Installing the Sunshade While aligning the mounting holes, position the sunshade onto the frame as shown in Figure Reelmaster 3100 and 3550 Machines or Groundsmaster 3500 and 3505 Machines (Serial #400000000 and up only) To properly align the frame, attach the frame-alignment bar to the mounting tabs on the rear of the sunshade frame with 2 flange-head bolts (5/16 x 1-1/4 inches) as shown in...
- Page 19 Loosely install a brace bracket to each brace Remove the flange-head bolts securing the with a bolt (1/2 x 2-1/2 inches), washer (1/2 frame-alignment bar to the frame and remove inch), and flange nut (1/2 inch) as shown in the alignment bar. Retain the bolts for mounting Figure the sunshade.
- Page 20 Operation Transporting the Machine When transporting the machine, use the 2 holes in the front of the sunshade frame (under the sunshade) to tie down the sunshade to a secure location on the machine and prevent it from raising up in the wind (Figure 38).