Table of Contents
Advertisement
Quick Links
CE Light Kit
Groundsmaster
Model No. 30660
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
© 2013—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
4000 Series Traction Unit with Yanmar Engine
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Flasher mount
Screw, 1/4 x 5/8 inch
Flange nut, 1/4 inch
Flasher module
Machine screw, #10 x 5/8 inch
Flat washer, 216 x .500
Lock nut, #10
Switch, turn signal
Switch, hazard
Wire harness, platform
Horn
Bolt (5/16 x 3/4 inch)
Flange nut (5/16 inch)
Horn switch
Horn button, rubber
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
–
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
Form No. 3378-192 Rev A
Installation Instructions
Use
Disconnect the battery
Install the flasher module
Install the turn signal and hazard
switches
Install the horn
Original Instructions (EN)
All Rights Reserved *3378-192* A
Printed in the USA.
Advertisement
Table of Contents
Related Manuals for Toro 30660
Summary of Contents for Toro 30660
- Page 1 Form No. 3378-192 Rev A CE Light Kit Groundsmaster ® 4000 Series Traction Unit with Yanmar Engine Model No. 30660 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
- Page 2 Procedure Description Qty. Headlamp bracket, R.H. (for models 30605 and 30609) Headlamp bracket, L.H. (for models 30605 and 30609) Rubber grommet (for models 30605 and 30609) Headlamp bracket (for model 30602, 30603, 30606 and 30607) Headlamp bracket, R.H. (for model Install the headlights 30604 and 30608) Headlamp bracket, L.H.
-
Page 3: Disconnecting The Battery
Disconnecting the Battery No Parts Required Procedure 1. Position the machine on a level surface, set the parking brake, lower the cutting units, turn the ignition off, and g021747 remove the key from the ignition switch. Figure 1 CAUTION 1. Steering tower cover If you leave the key in the ignition switch, someone could accidently start the engine and 2. - Page 4 Installing the Turn Signal and Hazard Switches Parts needed for this procedure: Switch, turn signal Switch, hazard Wire harness, platform Procedure g021714 1. From the under side the steering tower dash panel, Figure 4 press the plugs out of the holes shown in Figure 3. 1.
- Page 5 Installing the Horn Parts needed for this procedure: Horn Bolt (5/16 x 3/4 inch) g021715 Flange nut (5/16 inch) Figure 6 Horn switch 1. Horn switch 2. Horn button Horn button, rubber 3. Secure the horn switch to the tower by threading on the rubber horn button (Figure 6).
- Page 6 6. Route the headlight wire harness underneath the front edge of the operator's platform. 7. Insert each harness connector through the end of the appropriate harness bracket, out the hole (grommet) and connect it to the headlight (Figure 8). 8. Secure the headlight wiring harness to the headlight brackets and operator's platform with the harness clips and cable ties.
- Page 7 5. Secure the headlight wiring harness to the operator's platform with the harness clips and cable ties. 6. Install the steering tower cover. 7. The front and rear cab lights cannot be used for CE applications. Disable the front and rear cab lights as follows: •...
- Page 8 Installing the Rear Lamps Parts needed for this procedure: L.H. light mount R.H. light mount Rear lamp assembly Jumper wire harness Figure 12 Harness clip 1. Plate 3. Control arm 2. Right cover Procedure 2. Remove the (6) screws that secure the right cover to 1.
-
Page 9: Installing The Fuses
Installing the Fuses Parts needed for this procedure: Fuse, 10 amp Procedure Insert the 10 amp fuses into the fuse block slots shown in Figure 16 and Figure 17. g021710 Figure 15 1. Jumper wire harness 4. L.H. lamp mount 2. -
Page 10: Connecting The Battery
Connecting the Battery No Parts Required Procedure Connect the negative battery cable to the battery post. -
Page 11: Operation
Aiming the Headlights Operation 1. Loosen the mounting nuts and position each headlight Controls so that it points straight ahead. 2. Tighten each mounting nut just enough to hold the Light Switch headlight in position. 3. Place a flat piece of sheet metal over the face of the Press the light switch (Figure 18) to the On position to headlight.