Table of Contents
Advertisement
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Select
STEAM from the homepage. The correspond-
ing image appears on the display (B), together with a pro-
gress bar which fills gradually as preparation proceeds and
after a few seconds, steam to heat the liquid is delivered
from the hot water/steam spout;
4. When the required temperature or level of froth is reached,
interrupt steam delivery by pressing
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
If "Energy saving" is active, you may have to wait a few seconds
before steam is delivered.
Tips for using steam to froth milk
•
When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
•
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
•
For a creamier froth, rotate the container with slow move-
ments in an upward.
•
To avoid milk with poor froth or large bubbles, always clean
the spout (C4) as described in the following section.
Cleaning the hot water/steam spout after use
Always clean the hot water/steam spout (C4) after use to avoid
the build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and de-
liver a little water (see section "Delivering hot water"). Stop
delivery of hot water by pressing
2. Wait a few minutes for the hot water/steam spout to cool
down, then extract (fig. 18). Hold the spout with one hand
and with the other, turn the cappuccino maker and pull it
downwards (fig. 24).
3. Also remove the steam connection nozzle by pulling it
downwards (fig. 24).
4. Check the hole in the connection nozzle is not blocked.
5. Wash all parts with warm water.
6. Insert the connection nozzle, then the cappuccino maker
on the spout by pushing it upwards and turning it clockwise
until it is attached.
CUSTOMISING THE BEVERAGES
The aroma (when required) and quantity of the drinks can be
customised.
1. Make sure the profile for which you want to customise the
2. From the homepage, press
3. To access the customising screen, choose the beverage you
4. (Beverages with coffee only) CHOOSE COFFEE AROMA : Se-
;
5. CUSTOMISING COFFEE QUANTITY (OR WATER) STOP TO
6. When the amount reaches the minimum quantity you can
7. When the required quantity in the cup is reached, press
8. SAVE NEW SETTINGS? : Press YES or NO .
The appliance confirms if the values have been saved or not (de-
pending on the previous selection). Press
The appliance goes back to the homepage.
•
•
•
Beverage quantity table
Beverage
.
ESPRESSO
LONG
COFFEE
DOPPIO+
HOT WATER
MEMORISING YOUR PERSONAL PROFILE
The appliance allows you to memorise 6 different profiles, each
associated with a different icon.
The customised MY beverages AROMA and QUANTITY values are
saved in each profile (see section "Customising the beverages
based on the frequency of selection.
To select or enter a profile, press on the profile currently in use
22
beverage is active. You can select "MY" beverages for each
of the 6 profiles;
want to customise. The corresponding accessories must be
inserted;
lect the required aroma by pressing
;
SAVE : Preparation begins and the appliance displays the
quantity customising screen in the form of a vertical bar.
The ball alongside the bar represents the current quantity.
set,
is displayed.
.
Cappuccino and milk-based coffees: the coffee aroma is saved
first, followed by the quantity of first milk, then coffee;
HOT WATER: the appliance delivers hot water. Press
to save the required quantity.
Press
to exit programming. The values will not be
saved.
Standard
quantity
40 ml
160 ml
180 ml
120 ml
250 ml
"). The order in which all the beverages are displayed is
(B1);
or
and press
.
Programmable
quantity
20-80 ml
115-250 ml
100-240 ml
80-180 ml
20-420 ml
- Quick Links:
- Installation
- Descale
- Troubleshooting
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
