Cleaning The Infuser; Cleaning The Milk Container (D); Cleaning The Hot Water/Steam Connection Nozzle; Descale - Whirlpool W11 CM145 Instructions For Use Manual

Cleaning the infuser

The infuser must be cleaned at least once a month.
The infuser (A5) must not be removed when the appliance is on.
Do not use force to remove the infuser.
1. Make sure the machine is correctly turned off (see Turning
off).
2. Open the service door (A2).
3. Remove the drip tray (A14) and waste coffee container
(fig. 27).
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (fig. 32).
Do not use washing up liquid to clean the infuser. It would re-
move the lubricant applied to the inside of the piston.
5. Soak the infuser in water for about 5 minutes, then rinse.
6. After cleaning, replace the infuser (A5) by sliding it onto the
internal support and pin at the bottom, then push the PUSH
symbol fully in until it clicks into place (fig. 33).
If you encounter difficulty inserting the infuser, before inserting
it you must adapt it to the right dimension by pressing it force-
fully from the bottom and top as shown in the figure 34.
7. Once inserted, make sure the two coloured release buttons
have snapped out (fig. 35).
8. Replace the drip tray and the coffee ground container.
9. Close the service door.

Cleaning the milk container (D)

Clean the milk container each time you prepare milk as described
below:
1. Lift and remove the lid (D2);
2. Extract the milk container (D3) from the thermal casing
(D6), holding it by the two side grips.
The thermal casing must not be filled with or immersed
in water. Clean with a damp cloth only.
3. Remove the milk spout (D5) and intake tube (D4).
4. Turn the froth adjustment dial clockwise to the "INSERT"
position (fig. 36) and pull off.
5. Wash all the components of the frother thoroughly with
hot water and light washing-up liquid. All components and
the container are dishwasher safe, placing them in the top
basket of the dishwasher.
Make sure there are no milk residues on the hollow and
groove under the dial (fig. 37).
6. Rinse inside the froth adjustment dial seat (fig. 38) and the
milk frother connector hole.
7. Check that the intake tube and spout are not clogged with
milk residues.
8. Replace the dial (lining up the arrow with the word IN-
SERT), spout and milk intake tube.
9. Place the milk container in the thermal casing.
10. Place the lid back on the milk container.

Cleaning the hot water/steam connection nozzle

Each time you prepare milk, clean the connection nozzle (A10) to
remove milk residues from the gaskets (fig. 23).

DESCALE

• Before use, read the instructions and the labelling on the
descaler pack.
• You should use descaler product available at after sales
service. Using unsuitable descaler and/or performing des-
caling incorrectly may result in faults not covered by the
manufacturer's guarantee.
Descale the appliance when DESCALING NEEDED PRESS OK TO
START (~45min)
immediately, press
point 4.
To descale the appliance later, press
appears on the display to remind you that the appliance needs
descaling (the message appears each time you turn the appli-
ance on).
To access the descaling menu:
1. Press (B2) to enter the menu;
2. Press (B10) or
on the display;
3. Press to start the descaling cycle then follow the in-
structions on the display;
4. Empty the water tank. Press
5. ADD DESCALER (LEVEL A) AND WATER (UP TO LEVEL B) (fig.
40); Pour the descaler into the tank up to the level A marked
inside the tank, then add water (one litre) up to level B and
put the water tank back. Press
6. EMPTY GROUNDS CONTAINER and DRIP TRAY (fig. 27): re-
move, empty and replace the drip tray (A14) and grounds
container (A4). Press
7. PLACE 2.5L CONTAINER UNDER SPOUTS PRESS OK TO START
DESCALING :
Place an empty container with a minimum capacity of 2.5
litres under the hot water/steam spout (C4) and coffee
spouts (A13) (fig. 8);
24
appears on the display (B): to descale
and follow the instructions from
. The
(B8) until DESCALE appears
;
;
;
symbol