Table of Contents
Advertisement
Cleaning the milk container after use
WARNING
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout (D5).
Avoid contact with splashes of water.
Each time you use a milk function, TURN DIAL TO <CLEAN> PO-
SITION TO START CLEANING appears on the display and the milk
frother lid must be cleaned:
1. Leave the milk container (D) in the machine (you do not
need to empty it);
2. Place a cup or other recipient under the frothed milk spout
( g. 20);
3. Turn the froth adjustment dial (D1) to CLEAN ( g. 21).
CLEANING MILK CONTAINER UNDERWAY PLACE A RECIPIENT
UNDER MILK SPOUT appears on the display (B) ( g. 22)
together with a bar which gradually lls as cleaning pro-
ceeds. Cleaning stops automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the steam
connection nozzle (A10) ( g. 23).
•
To prepare a number of cappuccinos and milk based co ees,
clean the milk container after you have prepared the last
beverage only. To proceed with making the next beverages,
beverage only. To proceed with making the next beverages,
when the CLEAN message is displayed, press
•
If you do not clean the milk container, the
pears on the display to remind you that it needs cleaning.
•
The milk container can be kept in the refrigerator.
•
In some cases, before cleaning you must wait for the appli-
ance to heat up.
DELIVERING HOT WATER
WARNING
Do not leave the appliance unattended while hot water is being
delivered.
1. Make sure the hot water/steam spout (C4) is attached cor-
rectly to the hot water/steam connection nozzle (A10);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. Select
HOT WATER from the homepage. The corre-
sponding image appears on the display (B), together with a
progress bar which lls gradually as preparation proceeds;
4. The machine delivers hot water, then delivery stops auto-
matically. To interrupt hot water delivery manually, press
.
•
If "Energy Saving" mode is active, you may have to wait a
few seconds before hot water is delivered.
•
Preparation of hot water can be customised (see sections
"Customising the beverages" and "Memorising your per-
sonal pro le").
STEAM DELIVERY
WARNING
Do not leave the appliance unattended while steam is being
delivered.
1. Make sure the hot water/steam spout (C4) is attached cor-
rectly to the hot water/steam connection nozzle (A10);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Select
ing image appears on the display (B), together with a pro-
gress bar which lls gradually as preparation proceeds and
after a few seconds, steam to heat the liquid is delivered
from the hot water/steam spout;
4. When the required temperature or level of froth is reached,
interrupt steam delivery by pressing
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
If "Energy saving" is active, you may have to wait a few seconds
before steam is delivered.
.
symbol ap-
Tips for using steam to froth milk
•
When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
•
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
•
For a creamier froth, rotate the container with slow move-
ments in an upward.
•
To avoid milk with poor froth or large bubbles, always clean
the spout (C4) as described in the following section.
Cleaning the hot water/steam spout after use
Always clean the hot water/steam spout (C4) after use to avoid
the build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and de-
liver a little water (see section "Delivering hot water"). Stop
delivery of hot water by pressing
2. Wait a few minutes for the hot water/steam spout to cool
down, then extract ( g. 18). Hold the spout with one hand
and with the other, turn the cappuccino maker and pull it
downwards ( g. 24).
3. Also remove the steam connection nozzle by pulling it
downwards ( g. 24).
4. Check the hole in the connection nozzle is not blocked.
22
STEAM from the homepage. The correspond-
;
.
Advertisement
Table of Contents
Troubleshooting
