DeWalt DC013 Original Instructions Manual page 29

AC Operation (fi g. 4)
Unwrap power cord and plug into 115 or 230 V AC
wall outlet.
Inserting a Battery Pack (fi g. 2)
WARNING: Use only D
packs and chargers.
NOTE: Make sure your battery pack is fully charged.
If the battery pack does not produce sufficient
power, charge the battery pack following the
instructions in the manual of the charger.
NOTE: To ensure maximum performance and life of
NiCd, NiMH and Li-Ion batteries, charge the battery
for a minimum of 10 hours before first use.
1. Release the latch (h) to open the battery
compartment cover.
2. Insert the battery pack into the receptacle until it
is fully seated.
3. Close the battery compartment cover.
Operating the Radio (fi g. 1, 2)
Your charger/radio is equipped with memory
capacity in order to store the time and your selected
memory channels. When the radio is OFF, this
memory capacity is powered by one coin cell battery
that is included with the charger/radio.
TO INSTALL THE COIN CELL BATTERY
WARNING: When replacing battery,
replace it with the same brand and type.
Observe correct polarity (+ and –) when
replacing batteries. Do not store or
carry batteries so that metal objects can
contact exposed battery terminals.
1. Turn the charger/radio off and unplug from the
power source.
2. Open the battery compartment by lifting the
battery compartment latch (h).
3. Unscrew the screw (p) on the battery door (m).
4. Press down on the battery door latch and pull
to open.
5. Install the coin cell battery (n) according to the
diagram inside the coin cell battery area.
6. Replace the battery door, insert screw and
tighten.
7. Securely close the battery compartment.
NOTE: To reset the LCD display, clock and presets,
remove the coin cell battery and re-install it. Follow
this procedure if the screen seems to lock in place.
POWER/VOLUME ADJUSTMENT
1. To turn the radio on, turn the dial (a) clockwise
until you hear a click.
2. Turn the dial (a) clockwise to increase the
volume. To decrease the volume, turn
counterclockwise.
WALT battery
E
MODE FUNCTION
To choose one of the mode functions (FM, AM, or
AUX) push the mode button (d) until the desired
function is found. For example, if the radio is on FM,
seen in upper left portion of LCD display (g), push
the mode button twice to change to AUX.
TUNE OR SEEK FUNCTION
There are two tuning methods and one seek method
for finding the desired frequency.
To Tune:
Method 1: Push and hold down the right arrow
Method 2: Turn the tuning dial (b) clockwise to move
To Seek:
Press the right arrow button (c) once and release.
The tuner frequency will increase to seek the first
radio station with acceptable clarity and stop at
that station. The right arrow button may be pressed
again to continue seeking a radio station at higher
frequencies. The left arrow button may be pressed
to seek radio stations at lower frequencies. The seek
function is available in AM and FM modes.
TO PROGRAM THE MEMORY BUTTONS
Ten FM and five AM radio stations may be
independently set. After programming the buttons,
pressing 1, 2, 3, 4 or 5 will instantly change the
frequency to the preset station.
1. Turn power on.
2. Set the radio to desired station (see Tune or
Seek Function).
3. Press and hold one of the desired memory
buttons (f). The station setting begins flashing in
the LCD display (g). Continue to hold the button
down until the flashing stops. The memory
button is now set.
button (c) to quickly move the tuner up
the frequency band. Release the button
when the desired channel is reached.
To quickly move the tuner down the
frequency band, push and hold down the
left arrow button.
up the frequency band. Turn the tuning
dial counterclockwise to move down the
frequency band.
EN GL IS H
27