Advertisement
Quick Links
90" Squat Rack with Extended Pull-Up Bar
The 90" Fold-Up Murphy Rack is made by the creators of the original Profile
Folding Rack at PRx Performance
Performance Retractable Wall-Mounted Exercise Rack System, also known as
the Profile Rack and Profile PRO:
U.S. Patent No. 9,333,387
U.S. Patent No. 9,409,048
U.S. Patent No. 9,498,670
U.S. Patent No. 9,649,525
U.S. Patent No. 9,844,691
An up-to-date record of patents and patent pending items can be found at:
prxperformance.com/pages/prx-performance-patents-and-trademarks
For further assistance and installation video:
prxperformance.com/pages/murphy-rack
Fold-Up Murphy Rack
Powered by
®
and is Patented and Patent Pending. PRx
®
Advertisement
Related Manuals for PRx Performance Murphy Rack Fold Up
Summary of Contents for PRx Performance Murphy Rack Fold Up
- Page 1 ® The 90” Fold-Up Murphy Rack is made by the creators of the original Profile ® Folding Rack at PRx Performance and is Patented and Patent Pending. PRx Performance Retractable Wall-Mounted Exercise Rack System, also known as the Profile Rack and Profile PRO: U.S.
-
Page 2: Required Tools
90” Fold-Up Murphy Rack with Extended Pull-Up Bar (PUB) All Parts & Tools Needed Rack Specifications (WxHxD) Folded Up: 52” x 108” x 22.5” Folded Down: 52” x 90” x 39.5” Weight Capacity: 1000 lbs Required Tools Cordless drill 3/16” drill bit Stud finder Level Tape measure... -
Page 3: Getting Started
*If you find that your ceiling is not 108” please check page 12 for modified installation instructions or contact PRx Performance: support@prxperformance.com or 1-701-566-0452 3. Recruit a work partner to assist with steps that require lifting and holding the Rack 20.25”... - Page 4 Assemble Wall Brackets 1. Attach one Left Wall Bracket Ear (1A) and one Right Wall Bracket Ear (1C) to the Middle Wall Bracket (1B) using four M6 x 8 Tap Screws (16) 2. Be sure the ears on 1A and 1C are placed behind the Middle Wall Bracket (1B). When secured, the back of the wall bracket should be flush, and the ears should be pointing downward 3.
- Page 5 Starting Standard Installation Standard installation is for ceilings 108” or taller. If your ceiling is shorter than 108” please see page 12 for modifications, or contact PRx Performance: support@prxperformance.com or 1-701-566-0452 Locate Studs 1. Fold-Up Murphy Rack with Extended Pull-Up Bar is designed to be mounted to wood studs with standard 16”...
- Page 6 Mount Lower Bracket 1. Beginning with the right stud, measure 19” up from the floor and drill a pilot hole into the stud 2. Fasten a wall bracket to this stud with an M8 x 65 Lag Screw (5) and M8 Washer (6), but do not tighten all the way 3.
- Page 7 Linkage Arms Linkage Arm Assembly 1. Attach the Shock (3B) to the Linkage Arm (3A) using M6 x 16 Allen Bolt (3C) and M6 Nylock Nut (3D). Fully tighten M6 Nylock Nut (3D) 2. Once the shock is attached to the arm, place the M8 Nylock Nut (3E) onto the shock and lightly hand tighten.
- Page 8 Assemble Extended Pull-Up Bar 1. Lay out parts 4A through 4D to match the diagram below. Pay close attention to the holes h1 & h3 on 4A. Only one of the support sides (4A) will have a divot for the pull-up bar stud on 4B 2.
- Page 9 Attach Extended Pull-Up Bar To Uprights 1. Lay uprights on ground with the narrow side facing upward (with space between for Extended Pull-Up Bar) 2. Lay the Extended Pull-Up Bar flat on the ground so it is curving upward between the tops of the uprights (see diagram).
- Page 10 Attach Extended Pull-Up Bar to Linkage Arms Upper Linkage Arms 1. Attach the left linkage arm by removing the M16 x 85 Hex Head Bolt (11) from h5. Place the Plastic Spacer (7) on the inside of the linkage arm and place it against the top hole of the upright 2.
- Page 11 Attach Gas Shocks to Wall Brackets 1. *ATTENTION: TEAM LIFT the rack by holding each upright and pushing up against the wall. NOTE: The rack will be heavy 2. Attach Gas Shocks to ‘ear’ of the wall bracket with the 8M Nylock Nut (3E) - already attached to the shock - and tighten using two 12mm open-ended wrenches 3.
- Page 12 Ceiling not quite tall enough? Standard installation is for ceilings 108” or No PRx Folding Bench taller. If your ceiling is shorter than 108” Ceiling Bottom Space Rack please follow the measurements that most Height Bracket Bracket Between Depth closely correspond to your ceiling height. 108”...
- Page 13 PRx Performance LLC warrants to the original consumer purchaser that this product will be free of defects in material and workmanship for one (1) year from the date of purchase. PRx Performance will repair or replace the product, at our sole option, in the event of such a defect within the warranty period.
- Page 14 Free workout programs! Scan the code or follow the Compete against others! link to download the app. http://onelink.to/xfvf5f Looking for accessories for you new rack? Check them out at PRx Performance! prxperformance.com/collections/murphy-rack-accessories (701) 566-0452...
Need help?
Do you have a question about the Murphy Rack Fold Up and is the answer not in the manual?
Questions and answers