Record Settings; A Setting The Resolution; B Setting A Channel - Sanyo DSR-2108 Instruction Manual

RECORD settings

Press the MENU button and enter the password.
The MAIN MENU is displayed, select "RECORD" using the
control button ({|}~).
MAIN MENU
LIVE
NETWORK HDD SET
RECORD
RESOLUTION
CHANNEL
FRAME RATE
QUALITY
RECORDING
MOTION ZONE
MOTION SENSITIVITY
ALARM RECORDING
PRE RECORD
POST EVENT RECORD
AUDIO
TIMER SET
REAL-TIME REC SET
A
Setting the RESOLUTION
To set the resolution for the recordings.
Select "RESOLUTION" using the control button ({|)
and select a setting using the control button (}~).
FULL: NTSC: 704 × 480, PAL: 704 × 576
HALF: NTSC: 704 × 240, PAL: 704 × 288
QUAD: NTSC: 352 × 240, PAL: 352 × 288
35
RECORD SYSTEM
SERVICE
FULL
C 1 1
1 ips
NORMAL
CONTINUOUS
FULL ZONE
9
-- -- -- --
OFF
5 SECONDS
OFF
B
Setting a CHANNEL
To set the recording settings of each channel.
Select an item for each setting using the control button
({|) and select a setting value using the control button
(}~).
● Setting a CHANNEL
Select "CHANNEL" and select a channel.
CH1 - CH16
☞
In DSR-2108, CH1 - CH8.
● Setting the FRAME RATE (Unit: ips)
Select "FRAME RATE" and select a value.
NTSC: OFF/1/2/ ... 29/30 (ips)
PAL: OFF/1/2/ ... 24/25 (ips)
• Depending on the RESOLUTION settings, the
total FRAME RATE available is limited as
follows. If the total exceeds the limit the FRAME
RATE of other channels cannot be set.
If FULL is selected under resolution setting:
NTSC: It is possible to select up to a total of 30 frames for
channels 1 to 8 and up to a total of 30 frames for
channels 9 to 16
PAL: It is possible to select up to a total of 25 frames for
channels 1 to 8 and up to a total of 25 frames for
channels 9 to 16
☞
In DSR-2108, it is possible to select up to 30 (NTSC)/
25 (PAL) frames.
If HALF is selected under resolution setting:
NTSC: It is possible to select up to a total of 60 frames for
channels 1 to 8 and up to a total of 60 frames for
channels 9 to 16
PAL: It is possible to select up to a total of 50 frames for
channels 1 to 8 and up to a total of 50 frames for
channels 9 to 16
☞
In DSR-2108, it is possible to select up to 60 (NTSC)/
50 (PAL) frames.
If QUAD is selected under resolution setting:
NTSC: It is possible to select up to a total of 120 frames for
channels 1 to 8 and up to a total of 120 frames for
channels 9 to 16
PAL: It is possible to select up to a total of 100 frames for
channels 1 to 8 and up to a total of 100 frames for
channels 9 to 16
☞
In DSR-2108, it is possible to select up to 120 (NTSC)/
100 (PAL) frames.
• Calculation of the total FRAME RATE is
performed using the FRAME RATE set in the
RECORD menu or the FRAME RATE set in the
REAL-TIME REC SET menu, whichever is
greater.
● Setting the QUALITY
To select "QUALITY" and select the video quality.
Selections: NETWORK/ECONOMY/BASIC/NORMAL/FINE
● Setting the RECORDING
To select "RECORDING" and select the recording mode.
• CONTINUOUS (P17)
Recording is performed while this unit is turned on.
• MOTION recording (P17)
Recording is performed as soon as the internal motion
sensor of this unit reacts.