Canon iPF780 Series Service Manual page 195

Chapter 6
Display message
This type of paper is not compatible with
HP-GL/2.
Online: Print
Stop: Stop Printing
Load/Eject: Change Paper
Wrong paper size.
Check paper size setting in driver.
Online: Print
Stop: Stop Printing
! Hardware error.
03130000-2E21
Turn off printer, wait, then turn on again.
Hardware error.
03130031-260E
Turn off printer, wait, then turn on again.
Hardware error.
03130031-260F
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2618
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2805
Turn off printer, wait, then turn on again.
Hardware error.
03130031-290A
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2E23
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F13
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F14
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F16
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F17
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F1F
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F20
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F22
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F23
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F25
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F26
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F27
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F2A
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F2B
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F2E
Turn off printer, wait, then turn on again.
Hardware error.
03130031-2F32
Turn off printer, wait, then turn on again.
Excessive temperature or humidity.
Hardware error.
03130031-2F3A
Turn off printer, wait, then turn on again.
6-8
Code* Condition detected
03061000-2E15 Non-support media of HP-GL/2
03063000-2E08 Paper width mismatch
03130000-2E21 IEEE1394 port error
03130031-260E Gap detection error
03130031-260F Gap reference surface error
03130031-2618 VH voltage error
03130031-2805 Printhead abnormal low temperature
detection error
03130031-290A Hard disk disconnection error
03130031-2E23 Cutter unit failure
03130031-2F13 A/D converter external trigger output stop
detection hardware error 1
03130031-2F14 Writing to the ASIC register disabled
03130031-2F16 Mist fan rotation error
03130031-2F17 Platen suction fan lock detection error
03130031-2F1F Pump cam sensor error
03130031-2F20 Purge motor cam position error
03130031-2F22 Pump move timeout
03130031-2F23 Purge motor error
Pump inoperable
03130031-2F25 Unable to detect the carriage motor home
position
03130031-2F26 Carriage inoperable
03130031-2F27 Carriage move timeout
03130031-2F2A Unable to detect the feed roller home
position
03130031-2F2B LF operation failure
03130031-2F2E Roll travel timeout
03130031-2F32 Multi sensor error
03130031-2F35 Calibration environment error
03130031-2F3A Valve motor error
Action
Exchange for the compatible paper to HP-GL/2 before
reprinting.
Check the paper width and print.
Restart or replace the IEEE1394 board.
Check the carriage unit and surrounding parts.
Replace the main controller PCB.
Replace the multi sensor reference.
Check the power supply unit.
Replace printhead.
Check the connection status of HDD.
Check the cutter unit and sensor.
Check the carriage unit and surrounding parts.
Replace the main controller PCB.
Check the mist fan.
Check the platen suction fan.
Check the purge unit.
Check the purge unit.
Check the purge unit.
Check the purge unit.
Check the carriage unit.
Check the linear encoder for smears.
Check the carriage unit and surrounding parts.
Check the carriage unit and surrounding parts.
Check the feed roller encoder and surrounding part.
Check to see if paper has not jammed.
Check to see if paper has not jammed.
Check the feed motor and feed roller.
Check the roll feed unit.
Check the environment for interferences from outside
light.
Check if the temperature or humidity is within the scope
of calibration operation.
Check the ink supply unit.