1.14 Operating Safety Information; Explosion-Protection Safety Precautions; Operation Via Frequency Transformer; Using The Engineering Software Save & Restore And Ecom688 - ABB EBN853 Operating Instructions Manual

Pos: 4.30 /Überschriften/1.1/1-spaltig/S - U/Sicherheitshinweise zum Betrieb @ 0\mod_1140166424437_3101.doc @ 3205

1.14 Operating safety information

Pos: 4.31 /Sicherheit/Aktorik/Leistungselektroniken/Allgemein/Sicherheitshinweise zum Betrieb @ 13\mod_1191936932187_3101.doc @ 129254
Before switching on, ensure that the specified environmental conditions in the "Technical
Specifications" chapter or data sheet are complied with and that the power supply voltage
corresponds with the voltage of the electronic unit.
When there is a chance that safe operation is no longer possible, put the device out of operation
and secure against unintended operation.
When mounting the power electronic unit in areas that may be accessed by unauthorized
persons, take the required protective measures.
Pos: 5 /======= Seitenumbruch ======== @ 0\mod_1126532365768_3101.doc @ 3830
Pos: 6.1 /Überschriften/1/D - F/Ex-technische Sicherheitshinweise @ 9\mod_1181416415484_3101.doc @ 102826
2

Explosion-protection safety precautions

Pos: 6.2 /Überschriften/1.1/1-spaltig/A - C/Betrieb am Frequenzumformer @ 10\mod_1181565595390_3101.doc @ 102922
2.1

Operation via frequency transformer

Pos: 6.3 /Ex-technische Sicherheitshinweise/Aktorik/Antriebe/Allgemein/Betrieb am Frequenzumformer @ 9\mod_1181416045984_3101.doc @ 102803
• The frequency converter (electronic unit) may not installed or used within the hazardous
area.
• Check whether the electronic unit is loaded with the parameters of the actuator it is
connected to.
• Check the electronic unit for proper connection to the correct actuator.
• Setpoint monitoring is activated as default setting when the electronic unit leaves the
manufacturer. Do not de-activate this setting.
• Rapid traverse mode is not allowed on Ex actuators, and the feature cannot be activated
from the user interface.
• The Contrac power electronic unit must be upstream from the motor temperature monitoring
unit SD241B or similar, certified tripping unit.
Pos: 6.4 /Überschriften/1.1/1-spaltig/A - C/Benutzung der Engineering-Software Save & Restore und ECOM688 @ 17\mod_1199701584187_3101.doc @ 149819
2.2 Using the engineering software Save & Restore and ECOM688
Pos: 6.5 /Ex-technische Sicherheitshinweise/Aktorik/Antriebe/Leistungselektroniken/Benutzung der Engineering Software @ 17\mod_1199701466453_3101.doc @ 149796
Reinstalling the electronic unit software or individual data sections with the engineering software
Save & Restore or ECOM688 may only be performed in compliance with the relevant basic
conditions. It must be ensured, specifically, that the data record imported belongs to the
actuator type. After importing a data record, always check that all parameters for the application
such as speed and torque/force are configured accordingly.
Downdating the actuator operating system (UAPM software version) is not permitted.
Refer to the valid operating instructions for the engineering software ECOM688. The operating
instructions are available for download on the internet.
Pos: 7 /======= Seitenumbruch ======== @ 0\mod_1126532365768_3101.doc @ 3830
42/68-830-EN
Explosion-protection safety precautions
EBN853, EBN861 (Contrac) 11