Table of Contents
Advertisement
Advanced Remote Control Programming
The control box and the wireless remote control need
to be able to communicate via different RF channel
numbers in order to avoid interference with other
wireless remote controls or other remote control
equipment used near the system.
For this case the system offers ways to set up or
change the RF channel number.
LEARN PROCEDURE – WITH RF CHANNEL NUMBER
CHANGE (HOME MODE)
This channel setup procedure changes the
RF channel number from the factory setting.
The new RF channel number will be chosen
automatically by the system.
NOTE: Use this procedure to avoid interference
with other wireless remote controls or other
remote control equipment (e.g. remote
controlled toys, garage door openers...)
which are used near the system.
STEP 1
Disconnect the power cord (G) from wall outlet.
STEP 2
Press and hold both FLAT button (7) and
STOP button (16) for at least 10 seconds.
The current RF channel number will be
shown on the display (e.g. "2875") for
10 seconds.
22
CUSTOMER SERVICE: 1–800–821–6621
TEMPUR-Ergo
STEP 3
Press one of the massage buttons (10-15), (17-20)
to select a new random RF channel number. The
LCD shows the new random RF channel number on
the display.
STEP 4
Press the FLAT button (7) to confirm the
RF channel number and the wireless
remote control sends its current RF channel number
for 30 seconds. The LED signature light and the
backlight of the buttons are flashing during this time.
During this time also the LCD still shows the
RF channel number.
STEP 5
Re-connect the power cord (G) to the wall outlet
within 30 seconds of Step 4.
You will hear two "double-clicks." Then press the
STOP button (16).
NOTE: If the 30 seconds of RF channel number
transmission expire before the system is re-
connected to the power, the control box and the
wireless remote control will not work together.
In this case the procedure must be repeated.
NOTE: If the new RF channel number is
not confirmed with the FLAT button (7), the
RF channel number will remain unchanged and
the steps must be repeated.
Premier
®
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Tempur-Pedic and is the answer not in the manual?
Questions and answers
Where is the power output on or King bed?
Zero gravity button quit working
The zero gravity button may not be working due to several possible reasons:
1. Child Lock Activated – If the child lock is on, the adjustable base will not function. Hold the lock button and the light button for 3 seconds until the light blinks to disable it.
2. Power Issues – Ensure the power cord is plugged into a working, grounded electrical outlet. Test the outlet by plugging in another device.
3. System Reset Needed – Perform a system reset following the manual's instructions.
4. Connection Problems – Check if the connection cables are properly attached to the control box.
If these steps do not resolve the issue, consider contacting customer service.
This answer is automatically generated
Zero Gravity button does not work
If the Zero Gravity button is not working on your Tempur-Pedic mattress, it may be due to the base being inadvertently locked. To unlock it, hold down the foot up and foot down buttons at the same time until the light on the back of the remote blinks. If the issue persists, you may need to perform a system reset by holding the FLAT button until "RST" appears on the remote, then continuing to hold for 30–60 seconds as the bed moves. If no movement occurs after these steps, check the power connection and battery status of the remote.
This answer is automatically generated
How to reset my temperpedic
To reset a Tempur-Pedic mattress remote:
1. Remove the batteries from the remote.
2. Unplug the power supply from the control box.
3. Press the reset button on the control box.
4. Reinsert the batteries into the remote.
5. Plug the control box back into the power supply.
6. Press the flat button and the on/off button for the massage function.
This process resets the remote and reconnects it to the bed.
This answer is automatically generated