Sharp FO-CC500 Service Manual page 17

3. 6. Signal send mode
This mode is used to send various signals to the circuit during FAX
communication. Every push of START key sends a signal in the follow-
ing sequence. Moreover, the signal sound is also output to the speaker
when the line monitor of the soft switch is on.
[1] No signals (CML signal turn on)
[2] 14400BPS (V.33)
[3] 12000BPS (V.33)
[4] 14400BPS (V.17)
[5] 12000BPS (V.17)
[6] 9600BPS (V.17)
[7] 7200BPS (V.17)
[8] 9600BPS (V.29)
[9] 7200BPS (V.29)
[10] 4800BPS (V27ter)
[11] 2400BPS (V27ter)
[12] 300BPS (FLAG)
[13] 2100Hz (CED)
[14] 1100Hz (CNG)
3. 7. Memory clear
This mode is used to clear the backup memory and reset to the default
settings. (Various registrations are cleared.)
• The registered Cordless Handset information is not deleted by "Memory
clear".
3. 8. Shading mode
The mode is used for the shading compensation. For reading, set up
the special original paper.
The compensation memorizes the reference data of white and black for
reading.
Moreover, the memorized data is not erased even if memory clear mode
is executed.
3. 9. All black print
This mode is used to check the state of the printing head and to inten-
tionally overheat it. Whole dots are printed over the interval of 2 m. If it is
overheated or the printing sheet is jammed, press STOP key for the
end.
3. 10. Auto feeder mode
In this mode, a document is inserted and discharged to check the auto
feed function.
After this mode is started, set a document, and the document feed will
be automatically tested.
3. 11. Entry data send
This mode is used to send the registered data to another machine and
make the other machine copy the registered content.
Before sending in this mode, it is necessary to set the other machine at
the entry data receive mode.
The following, information will be sent to the remote machine:
1. Telephone list data
2. Sender register data
3. Optional setting content
4. Soft switch content
5. Junk fax number list
6. Timer reservation data (Only on the model which timer reserva-
tion is possible.)
7. Recording setting list data
3. 12. Entry data receive
In this mode, the registered data sent from the other machine is receiv-
ed and the received data is registered in the machine. When this mode
is used for receiving, the other machine must be in the entry data send
mode.
After receiving is completed, the following lists are printed.
1. Telephone list data
2. Sender register data (The passcode No. is also printed if the poll-
ing function is provided.) (*)
3. Optional setting list (*)
4. Soft switch content
5. Junk fax number list (*)
6. Timer reservation data (Only on the model which timer reserva-
tion is possible.)
7. Recording setting list data (*)
(*): Refer to SETUP LIST
3. 13. Flash memory check
Data is written into and read from the flash memory to check data con-
formity. When the unit enters this mode, the check is started.
3. 14. Flash memory clear
Data in the flash memory is cleared (memory clear). When the unit en-
ters this mode, the check is started.
*Operation of hardware and signal in the flash memory check mode and
flash memory clear mode, and the result of check.
The result is announced by the buzzer beeps. The result of check is
printed.
1 → Memory error
Beeps
3. 15. RF TX mode
This mode is for measurement of RF signal send level. When you press
START key, the DSS unit move to be in the continuous signal send mode
until you press STOP key. It needs exclusive measuring device.
3. 16. RF RX mode
This mode is for measurement of RF signal send level. When you press
START key, the DSS unit move to be in the continuous signal receive
mode until you press STOP key. It needs exclusive measuring device.
3. 17. DTMF CDL ID RX
When you press START key, the display change to 'LINE STANDBY'.
And, it waits for the start signal (DTMF) of the System ID input protocol.
The exclusive writer at the product line only corresponds to the protocol.
3. 18. Keypad test mode
From this mode, you can enter the diag mode of the DSS unit
(CONEXANT Merlin). The purpose of these items is to measure the wire-
less communication specification of this unit. By enter the access code
written in Conexant's user guide, you can start the desired menu. To
implement this menu, this user guide is necessary.
2 – 4
FO-CC500A
FO-K01A