Epson FX-80 User Manual page 346

ESCape
"&."
CHR$(n) CHR$(c1) CHR$(c2) CHR$(A) CHR$(Dl) ... CHR$(Dll)
Defines characters c1 to c2 in RAM area: See User-defined characters.
ESCape "*" CHR$(m) CHR$(nl) CHR$(n2). Selects Graphics Density n. See
Graphics Mode.
ESCape "-0". Turns Underline Mode off. See Underline Mode.
ESCape "-I". Turns Underline Mode on. 'See Underline Mode.
ESCape "I" CHR$(n). Selects channel n. See Tabs, vertical.
ESCape "0". Sets line spacing to 118". See line spacing.
ESCape "I". Sets line spacing to 7/72". See line spacing.
ESCape "2". Sets line spacing to 1116". See line spacing.
ESCape "3" CHR$(n). Sets line spacing to n/216". See line spacing.
ESCape "4". Turns on Italic Mode. See Italic Mode.
ESCape "5". Turns Italic Mode off. See Italic Mode.
ESCape "6". Enables printing of control codes 128-159. See ASCII codes; User-
defined characters.
ESCape "7". Returns codes 128-159 to control codes. See ASCII codes; User-
defined characters.
ESCape "8". Turns paper-out sensor off. See Paper-out sensor.
ESCape "9". Turns the paper-out sensor on. See paper-out sensor.
ESCape ":" CHR$(nl) CHR$(n2) CHR$(n3). Copies ROM characters to the user
RAM area. See User-defined characters.
ESCape,"(". Turns on Unidirectional Mode. See Unidirectional mode.
ESCape
"~".
Sets the high-order bit off. See Bit, high-order.
ESCape ")". Sets the high-order bit on. See Bit, high-order.
ESCape
"@".
Sets Master Reset Code. See Master Reset Code.
ESCape "X' CHR$(n). Sets line spacing to
n/72". See line spacing.
ESCape "B" CHR$(nl) CHR$(nk) CHR$(O). Sets the vertical tab stops (Vtabs).
See Tabs, vertical.
ESCape "C" CHR$(O) CHR$(n). Sets the form length in inches. See form length.
ESCape "C" CHR$(n). Sets the form length in lines. See form length.
ESCape "0" CHR$(nl). Sets the horizontal tabs. See Tabs, horizontal.
ESCape "E". Turns Emphasized Mode on. See Emphasized Mode.
ESCape "F". Turns Emphasized Mode off. See Emphasized Mode.
ESCape "G". Turns Double-Strike Mode on. See Double-Strike Mode.
ESCape "H". Turns Double-Strike Mode off. See Double-Strike Mode.
ESCape "10". Returns codes 0-31 to control codes. See ASCII codes; User-defined
characters.
ESCape "11". Enables printing of control codes 0-31. See ASCII codes; User-
defined characters.
ESCape
"J"
CHR$(n). Produces an immediate one-time line feed of n/216"
without a carriage return. See Line Feed.
ESCape "K" CHR$(nl) CHR$(n2). Turns Graphics Mode, Single-Density on. See
Graphics mode.
ESCape "L" CHR$(nl) CHR$(n2). Turns Graphics mode, Double-Density on. See
Graphics Mode.
ESCape "M". Turns Elite Mode on. See Elite Mode.
ESCape "N" CHR$(n). Produces a variable Skip-Over-Perforation (SOP). See
skip-over-Perforation.
ESCape "0". Turns Skip-Over-Perforation off. See Skip-Over-Perforation.
ESCape "P". Turns Elite Mode off. See Elite Mode.
ESCape "Q" CHR$(n). Sets the right margin. See margins.
ESCape "R" CHR$(n). Selects the international charater set n. See international
character set.
ESCape "SO". Turns Subscript Mode on. See Script mode.
ESCape "SI". Turns Superscript Mode on. See Script mode.
ESCape "T". Turns either script mode off. See Script Mode.
ESCape "UO". Turns Continuous Unidirectional Mode off. See Unidirectional
mode.
316