Related Manuals for Toro Sand Pro Cyclone 1000
Summary of Contents for Toro Sand Pro Cyclone 1000
- Page 1 Form No. 3350–897 Cyclone 1000 Debris Blower Sand Pro Model No. 08857—Serial No. 240000001 and Up Operator’s Manual English (EN)
-
Page 2: Table Of Contents
....... . Dealer or Toro Customer Service and have the model and serial numbers of your product ready. -
Page 3: Safety
– Watch out for traffic when near or crossing roads. complete Model and Serial Number to The Toro Always yield the right-of-way. Company, 8111 Lyndale Avenue South, Bloomington, Minnesota 55420-1196. - Page 4 Toro replacement parts and may result. accessories to keep the machine all Toro. Never use Before disconnecting or performing any work on the “will-fit” replacement parts and accessories made by hydraulic system, all pressure in the system must be other manufacturers.
-
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 98-3114 1. Entanglement hazard—stay away from moving parts. 98-3110 1. - Page 6 98-3112 1. Warning—read the instructions before servicing or performing 105-3137 maintenance on the electrical wiring. 1. Read the Operator’s 2. Grease every 8 hours. Manual. 3. Add grease here. 98-3116 105-0708 1. Engage 2. Disengage 1. Warning—thrown objects 98-8665 1. Entanglement hazard, shaft—remove the ignition key, wait for 105-0709 moving parts to stop, and read the instructions before servicing or performing maintenance;...
-
Page 7: Specifications
Specifications Note: Specifications and design subject to change without notice. General Specifications Backward curved, cast aluminum fan. 12 blades per side, 21” outside diameter, 6.375” width, 34 lbs. 10 gauge steel face plates welded to 10 gauge wrapper. Increasing scroll from Fan Housing cutoff. -
Page 8: Setup
Setup Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total setup cannot be completed. Description Qty. Blower Assembly Mounting *Relay Mount to Sand Pro frame *Capscrew #10–24 x .38” lg. Connect neutral switch wire to harness *Nut #10–24 *Wire Harness... -
Page 9: Install Wire Harness
Read before operating the machine. Parts Catalog Registration card Fill out and return to Toro. Note: Determine the left and right sides of the machine from the normal operating position. Note: One of the following installation kits is required to On Sand Pro 5000/5020 only –... -
Page 10: Install Spline Shaft
Install Spline Shaft Mount Bumper Assembly 1. Remove fasteners securing output shaft cover to rear of 1. Mount bumper assembly to blower with (4) 3/8–16 x engine on Sand Pro 5000/5020 (Fig. 3) or to rear of .50” Lg. capscrews, .40 I.D. x .81 O.D. flatwashers and hydrostat on Sand Pro 2020/3020. - Page 11 On Sand Pro 5000/5020 – Mount top of receiver bracket to frame with a 3/8–16 x 1.25” lg. capscrew, (2) .40 I.D. x .81 O.D. flat washers, .625” lg. spacer and locknut. Mount bottom of receiver bracket to frame with a 1/2–13 x .875” lg. capscrew and (2) .56 I.D. x 1.063 O.D.
-
Page 12: Install Drive Shaft
Install Drive Shaft Grease Blower 1. Insert drive shaft spline (supplied in installation kit) into Before the Debris Blower is operated, it must be greased to blower coupler (Fig. 10). assure proper lubrication. Refer to Lubrication section of manual. Failure to properly grease the unit will result in 2. -
Page 13: Before Operating
Before Operating Adjust Discharge Opening The discharge opening (Fig. 11) is adjustable to increase or decrease air output velocity and volume. Decreasing discharge opening size will increase velocity. 1. Loosen discharge opening deflector mounting screws. 2. Pivot deflector to desired opening. 3. -
Page 14: Operation
Operation Lubrication Controls Grease Bearings & Bushings The debris blower must be lubricated regularly. If machine Clutch Engagement Lever is operated under normal conditions, lubricate castor and fan bearings and bushings with No. 2 general purpose Pull lever (Fig. 12) upward to engage clutch, push lever lithium base grease or molybdenum base grease, after every downward to disengage clutch. -
Page 15: Maintenance
Maintenance Adjusting Belt 1. Remove capscrews, flatwashers and locknuts securing bumper assembly to blower (Fig. 14). Remove bumper assembly. Figure 15 1. Fan shaft bearing 3. Back cover assembly 2. P.T.O. shaft bearing 9. Replace belt. Make sure belt is routed around fan and P.T.O. -
Page 16: The Toro General Commercial Products Warranty
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.