Sharp AR-FX12 Service Manual page 38

Large item Medium item
TEL/FAX auto
switch
External
telephone call
Communication General
SG3
Send G3/SG3
SG3
G3
Receive G3/SG3
SG3
G3
Receive print Paper
selection
Content of switch
Voice answering send level to the line
Ring back tone ON time
Ring back tone OFF time
Signal send level
ECM (Valid for other than V.34)
(Reflected on V.21 DIS/DCS.)
Timer setup between flag and address
(V.21-FSK)
Coding capacity in send/receive
(V.34 communication)
(Reflected on DIS/DCS/DTC.)
Coding capacity in send/receive
(Reflected on DIS/DCS/DTC)
(Other than V.34)
V.34 mode function(When call out and
polling)
V.34Symbol Rate Mask (when receiving)
V.34 mode function in manual
communication
Countermeasures against echo in
transmission
(Used to set the hold time from DIS reception
to signal sending.)
DIS reception confirmation in G3
transmission
V.34 mode transmission speed
V.34 mode transmission speed
Echo suppresser tone setup
Modem transmission speed (Except for V.34)
(DCS)
DCS-TCF interval time
Error process in RTN reception
CSI send
V.34 mode reception speed
Countermeasures against echo in reception
(CED tone send interval)
Reception modem speed fixed
(other than V.34) (DIS)
EOL detection timer
RTN send line error rate
EQM judgment threshold value
when confirming TCF reception
Judgment method in confirmation of TCF
reception
Sub scan length judgment
FAX paper exit tray setup <Dragon>
Received data print condition setup
Automatic reduction/dispose setup
Setup of magnification ratio in automatic
reduction
Reduction/dispose setup when printing A3,
11X 17
Duplex reception print
Rotation print
Received document output setup
11 x 17 paper reception width setup
Reception size specification
(Indicates reception capacity.)
AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-26
Key operator Soft SW No.
SW 51-1
SW 10-1~4 External telephone call disable
CNG detection disable
SW 10-5~8 External telephone call disable
CNG detection disable
SW 15-1~8 When the remote machine does not
receive signals in a proper level.
Initial setup SW 17-5 Error resend frequently occurs, resulting
in extended communication time.
SW 20-3~4 Communication error in a satellite line
SW 17-3~4 Error in JBIG mode
SW 17-7~8 Error in JBIG mode
SW 43-1 Frequent errors in SG3 communication
SW 43-3~6 Frequent errors in SG3 communication
SW 42-8 Frequent errors in SG3 communication in
FAX service
SW 20-7 An error occurs in phase B.
SW 20-2 An error occurs in phase B.
SW 25-5 CED signal detection error
SW 44-1~4 An error occurs in SG3 communication.
SW 27-1~4 An error occurs in V.29 communication
SW 16-1~4 To uncertain/certain receiver
SW 24-1 An error occurs in training.
SW 30-2 OK is displayed when RTN is received.
SW 20-1
SW 44-5~8 An error occurs in SG3 communication.
SW 20-6 An error occurs n phase B in reception.
SW 16-5~6 Fall back or an error occurs due to poor
line conditions.
SW 23-1 EOL time up occurs frequently.
SW 23-7~8 Line error occurs frequently.
SW 24-2 TCF reception error occurs.
SW 24-3 TCF reception error occurs.
SW 35-2 Print is not made on the selected paper.
Receive setup SW 28-7~8 Print is not made on the selected paper.
Receive setup SW 35-3~4 To make divided print instead of
reduction print.
Receive setup SW 35-7 To disable reduction print.
SW 36-1~8 To disable reduction print on fixed size
paper.
SW 35-8 Print is not made on the selected paper
when A3-11x17 size document is
received.
Receive setup SW 34-8 To make duplex print of received
document
SW 35-1 To disable rotation print
SW 35-5 To print after reception of each page
SW 37-3 To print 11x17 document as B4 width
SW 37-1~2 To limit the reception size.
Purpose of use