Advertisement
Available languages
Available languages
E N G L I S H
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or
.
For 115 V tools, use plugs to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved triple-core extension
cable suitable for the power input of this tool (see technical data).
The minimum conductor size is 1.5 mm
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 -
2.0
2.1 -
3.4
3.5 -
5.0
5.1 -
7.0
7.1 - 12.0
12.1 - 20.0
230
0 -
2.0
2.1 -
3.4
3.5 -
5.0
5.1 -
7.0
7.1 - 12.0
12.1 - 20.0
Unpacking (fig. A1 & A2)
Remove the saw from the packing material carefully using the carrying
handle (9).
The package contains:
1 Assembled Mitre Saw
1 Blade spanner
1 305 mm TCT saw blade
2 Clamps (DW704 only)
1 Instruction manual
1 Exploded drawing
en - 3
2
.
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• Press down the operating handle (1) and pull out the lock down pin (28),
as shown in fig. A2.
• Gently release the downward pressure and allow the arm to rise to its
full height.
Description (fig. B1 - B3)
B1
1 Operating handle
2 Moveable lower guard
3 Fence right-hand side
4 Mitre clamp knob
5 Mitre latch
6 Mitre scale
7 Fence left-hand side
8 Bench mounting holes
9 Carrying handle
10 Head lock up release lever
11 Rear lower guard
12 Bevel scale (DW705 only)
13 Padlock hole
14 Motor housing
15 Spindle lock button
16 Brush inspection cap
17 Trigger switch
B2
18 Blade spanner
19 Angle position stop (DW705 only)
20 Dust spout
21 Bevel clamp handle (DW705 only)
22 Hand indentation
23 Upper fence left-hand side clamping knobs (DW705 only)
24 Upper guard
25 Vertical position adjustment stop (DW705 only)
26 Bevel position adjustment stop (DW705 only)
27 Kerf plate
28 Head lock down pin
B3
29 Work support extension
30 Adjustable length stop
60
31 Work piece clamp
32 Dustbag
10
15
Assembly
20
25
-
Prior to assembly always unplug the tool.
-
6
The motor and guards are already assembled onto the base.
6
15
Bench Mounting (fig. C1 & C2)
15
• Holes (8) are provided in all four feet to facilitate bench mounting.
20
Two different sized holes are provided to accommodate different sizes
-
of bolts (33). Use either hole; it is not necessary to use both.
Always mount your saw firmly to prevent movement. To enhance the
portability, the tool can be mounted to a piece of 12.5 mm or thicker
plywood which can then be clamped to your work support or moved to
other job sites and reclamped.
• When mounting your saw to a piece of plywood, make sure that the
mounting screws do not protrude from the bottom of the wood.
The plywood must sit flush on the work support. When clamping the
saw to any work surface, clamp only on the clamping bosses where
the mounting screw holes are located. Clamping at any other point will
interfere with the proper operation of the saw.
20
Advertisement
