Opticum XS65-COMBO Quick Start Manual

Quick start
HD Digital Satellite Receiver
One smart card reader
ƒ
Support of SD / HD (MPEG2 / MPEG4
ƒ
H.264), DVB-S, DVB-S2, DVB-T
High definition video output – HDMI
ƒ
Port USB 2.0
ƒ
Low power consumption in Standby mode –
ƒ
below 1 W
Support of DiSEqC 1.0, 1.1
ƒ
Electronic Programme Guide – EPG
ƒ
Display on the front panel – LED 4 digits
ƒ
Model ID:XS65-COMBO MC/2014/09
XS65-COMBO_ENG_REV02.indd 1
Remote control
Button Function
turns the receiver on/off from/
POWER—
to a standby mode
selects the resolution of the
HDMI
image output
turns on/off the audio sound
MUTE —
select channels; let you enter
Number buttons programming parameters in
the menu
sets the sleep timer for
10/30/60/90/120 min
displays and scrolls to your
FAV
favourite list of channels
returns to the previous channel
displays the main menu on the
MENU screen; returns to the previous
menu
displays the infobar of the
INFO
programme
displays the electronic
EPG
programme guide
EXIT Exits the on screen-menu
Remote control
Button Function
adjust the volume, moves the cursor to the left or right in the
/
menu
/ changes channels, moves the cursor up and down
OK displays the channels list, selects the menu options
TV / selects the TV/Radio source
FIND lets you find a channel by its number
SUB-T subtitles settings
HOME optional function ( available in some versions)
STATUS displays the window of the status
AUDIO audio settings
TEXT displays Teletext for a current channel
PVR displays the list of recordings (optional)
MAILBOX displays the list of Your payments
SLOW, SKIP-,
SKIP+, REW, FF,
sets video options (time shift, playing, recording)(optional)
PLAY, PAUSE,
STOP, REC
RED, GREEN,
YELLOW, BLUE, Colour buttons: use them according to the instruction on screen
WHITE, BLACK
Basic connection
Package content Automatic power turn-off
After purchasing the receiver , please In accordance with the current EU requirements, the receiver you have just purchased is
equipped with a feature Automatic Power OFF. It switches the receiver to a stand-by mode
unpack it and make sure the following
after 3 hours from its last activity. It means that if within this time no command is sent to the
items are included:
receiver from the remote control buttons or keypad on the front panel, it gets turned off. The
• Receiver
moment of turning off will be proceeded ( 2 minutes earlier) by a relevant message on the screen
• Remote control
of the TV set. Please note that this feature is enabled by default in EU countries, however, at
• Quick start manual
your own request, it can be disabled by choosing an appropriate option in the menu.
• Batteries – 2 x AAA ( optional)
Connecting to an external USB drive
To install batteries in the remote control
While selecting and using an external USB drive ( an external hard drive, flash memory), make
remove the battery compartment cover. If
sure:
there are batteries already there, remove
• it is compatible with USB 2.0 standard and has appropriate write and read speed
them and insert the new ones. Make sure
the positive and negative ends are facing • it has one single partition adequately formatted
the correct direction as shown. Replace
• if necessary, it can be supplied with power from an external charger (in particular it refers to
the battery compartment cover. external USB hard drives that have high power consumption)
• you do not disconnect it during the process of data writing/reading
Connecting
• it is not completely full or highly fragmented
(1) Connect the satellite cable into the
SAT input on the receiver and connect
Negligence of the above recommendations can lead to faulty work of the devices and cause
aerial into the AERIAL IN.
their damage.
(2) Connect the receiver with a flat panel
TV using a HDMI cable, or
The manufacturer does not take responsibility for damage caused directly or indirectly by any
(3) Connect the receiver with a
problems resulting in data loss on the external USB drive connected to the receiver. Nor does
conventional TV, using a SCART cable.
he give warranty on any other data on the USB drive connected to the device in case of its faulty
(4) Finally, plug the power cord into a wall work.
outlet.
Turn on the TV set and turn on the receiver
using POWER button on the remote
control. After few minutes, the interface
of the product set-up should be displayed
on screen (OSD). If the TV set does not
1 2 3 4 display OSD, the wrong input source
must have been selected. See the TV
set documentation to double check the
settings.
Notes on usage
2014-09-11 12:09:11