Related Manuals for Makita 3702B
Summary of Contents for Makita 3702B
- Page 1 Tkimmer 1/4” MODEL 3702B INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS No load speed N e t weight Overall lenqth Collet chuck c a p a c i t y (RPMI _ ~ _ _ _ _ ~ _ _ 13 5 lbsl...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed f r o m tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF w h e n plugging in. OUTDOOR USE EXTENSION CORDS.
-
Page 4: Additional Safety Rules
ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. Handle the bits very carefully. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. - Page 5 (after it has been removed from the tool) NOTE : The trimmer shoe is factory installed on the tool. Use the bolts, wing nuts, spring washers...
- Page 6 Adjusting amount of chamfering To adjust the amount of chamfering, loosen the wing nuts and adjust the trimmer shoe. CAUTION With the tool unplugged and switch in the "OFF" position, rotate the collet nut on the tool several times to be sure that the bit turns freely and does not contact the tool base or trimmer shoe in any way.
- Page 7 When using the trimmer shoe, the straight guide or the trimmer guide, be sure to keep it on the right side in the feed direction. This will help to keep i t flush with the side of the workpiece.
- Page 8 Straight guide The straight guide effectively used for straight cuts when chamfering or grooving. Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. Loosen the wing bolts and secure the tool base horizontally.
- Page 9 Circular work 0Circular work may be accomplished if you assemble the straight guide and guide plate as shown in the figure below. Min. and max. radius of circles to be cut (distance between the center center of bit) are as follows : Min.
- Page 10 Trimmer guide Trimming, curved cuts for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Loosen the wing bolts and secure the tool base horizontally. Install the trimmer guide on the tool base with the clamp screw (A).
- Page 11 Templet guide The templet guide provides a which the bit passes, allowing use of the trimmer with templet patterns. Remove the tool base from the tool. Loosen the wing bolts and secure the tool base horizontally. Loosen the two screws on the tool base.
- Page 12 Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding along the side of the templet. NOTE The workpiece will be cut tance ( X ) between the router bit and the outside of the templet guide. The distance ( X ) can be calculated using the following equation : Distance ( X )
-
Page 13: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. switched off and unplugged before attempting t o perform... - Page 14 ACCESS0 R I ES CAUTION : These accessories or attachments are recommended for use w i t h your Makita t o o l specified i n this manual. The use any other accessories The accessories o r attachments should be used only in the proper and intended manner.
- Page 15 Bits STRAIGHT -Single Flute STRAIGHT 2 Flute HINGE MORTISING VEINING -Single Flute SPEED STEEL HIGH PART 733232-6A 5/16 CARBIDE TIPPED PART NO 733003-2A 3/16 7116 733003-4A 733003-EA 5/16 HIGH SPEED STEEL (STRAIGHT - 2 Flute1 PART NO 733233-4A 5/16 CARBIDE TIPPED PART NO.
- Page 16 ROUND NOSE -I& CARBIDE TIPPED &, CORE BOX 4 D C HIGH VEE GROOVING CARBIDE TIPPED 14" DOVE TAIL CARBIDE TIPPED PART NO. 733008-2A 15132 733008-4A 9/16 SPEED STEEL PART 7 3 3 2 3 a - 2 ~ 1 / 4 P A R T 733009-2A PART...
- Page 17 PANEL PILOT CORNER ROUNDING BEADING COVE HIGH SPEED STEEL PART NO. 733236-0A CARBIDE TIPPED Ball Bearing Pilot 733120 OA 7331 20 2A REPLACEMENT BEARING HIGH SPEED STEEL - S o l i d Pilot P A R T N O 733240 2A 11/16 3/16...
- Page 18 ROMAN OGEE CARBIDE TIPPED - Ball Bearing Pilot FLUSH TRIMMER -Self Piloting SOLID CARBIDE 7" BEVEL TRIMMER Self-Piloting SOLID CARBIDE 2 FLUTE FLUSH TRIMMER i ? t CARBIDE TIPPED P A R T N O . 733123-2A 15/32 REPLACEMENT BEARING - NO, 733132-2A PART NO.
- Page 19 COMB1 NATION F LUSH/2Z0 BEVEL TRIMMER 3 FLUTE FLUSH TRIMMER ASSEMBLY -Self Piloting 3 FLUTE 22" BEVEL TRIMMER ASSEMBLY -self Piloting -I[+ 3 F L U T E FLUSHREPLACEMENTCUTTER CARBIDE TIPPED 733128-6A 7/16 SOLID CARBIDE CUTTER P A R T N O .
- Page 20 3 FLUTE 22" BEVEL REPLACEMENT CUTTER 114" REPLACEMENT ARBOR BALL BEARING PILOT S O L I D CARBIDE P A R T N O . 733129-8A FOR BEVEL TRIMMER ASSEMBLY PART NO 733131,2A FOR FLUSH TRIMMER ASSEMBLY A N D NO 733129-4A PART NO.
- Page 21 TRIMMER Model 3702B N o t e T h e s w i t c h , noise suppressor and o t h e r p a r t c o n f l g u r a t l o n s...
- Page 22 ' k ,' o " ,"., DESCRIPTION Cord Cord Guard Name Plate Rivet Hex Nut M 5 Pan Head Screw M4x10 IWith Washerl TRIMMER BASE ASSEMBLY Wing Nut M 5 Spring Washer Flat Washer Screw M6x18 Spring Washer6 Washer Flat Flat Washer...
- Page 23 Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.