Makita 3709 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Trimmer
  5. 3709
  6. Instruction manual
Makita 3709 Instruction Manual

Makita 3709 Instruction Manual

Hide thumbs Also See for 3709:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
Trimmer
MODEL 3709
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
DOUBLE
INSULATION
M A N U A L
006612

Advertisement

Table of Contents
loading

Related Manuals for Makita 3709

Summary of Contents for Makita 3709

  • Page 1 Trimmer MODEL 3709 006612 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    Responsible manufacturer: Power supply Makita Corporation Anjo Aichi Japan The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They...

  • Page 3: General Safety Rules

    GENERAL SAFETY RULES GEA001-2 WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains- operated (corded) power tool or battery-operated (cordless) power tool.

  • Page 4: Additional Safety Rules

    Remove any adjusting key or wrench sures reduce the risk of starting the power before turning the power tool on. A wrench tool accidentally. or a key left attached to a rotating part of the Store idle power tools out of the reach of power tool may result in personal injury.
  • Page 5 13. Do not touch the bit immediately after operation; Make sure the bit is not contacting the work- piece before the switch is turned on. it may be extremely hot and could burn your skin. Before using the tool on an actual workpiece, let 14.

  • Page 6: Functional Description

    FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting bit protrusion 006613 To adjust the bit protrusion, loosen the clamping nut and move the tool base up or down as desired by turning the adjusting screw.

  • Page 7: Operation

    OPERATION Set the tool base on the workpiece to be cut without the bit making any con- tact. Then turn the tool on and wait until the bit attains full speed. Move the tool forward over the workpiece surface, keeping the tool base flush and advancing smoothly until the cutting is complete.
  • Page 8 Remove the chip deflector. 006627 Loosen the screws and remove the base protector. Place the templet guide on the base and replace the base protector. Then secure the base protector by tightening the screws. 1. Base protector 2. Screws 3. Screwdriver Secure the templet to the workpiece.
  • Page 9 Remove the chip deflector. 006624 Attach the straight guide with the clamp screw (A). Loosen the wing nut on the straight guide and adjust the distance between the bit and the straight guide. At the desired distance, tighten the wing nut securely. When cutting, move the tool with the straight guide flush with the side of the workpiece.
  • Page 10 Align the center hole in the straight guide with the center of the circle to be cut. 006625 Drive a nail less than 6 mm in diameter into the center hole to secure the straight guide. Pivot the tool around the nail in clockwise direction. Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide.

  • Page 11: Maintenance

    CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 12 “U”Grooving bit 005117 006486 1/4" “V”Grooving bit 005118 006454 90˚ 1/4" Drill point flush trimming bit 005120 006487 1/4" Drill point double flush trimming bit 005121 006488 1/4" Corner rounding bit 005125 006489 1/4" 1/4"...
  • Page 13 Chamfering bit 005126 006462 30˚ 30˚ 30˚ E 1/4" 45˚ 45˚ 45˚ E 1/4" 60˚ 60˚ 60˚ E 1/4" Cove beading bit 005129 006464 1/4" 1/4" Ball bearing flush trimming bit 005130 006465 1/4" Ball bearing corner rounding bit 005131 006466 1/4"...
  • Page 14 Ball bearing beading bit 005133 006468 1/4" 1/4" Ball bearing cove beading bit 005134 006469 1/4" 1/4" Ball bearing roman ogee bit 005135 006470 1/4" 1/4"...
  • Page 15 Memo...
  • Page 16 Makita Corporation Anjo, Aichi, Japan 884629-224...

Table of Contents