Additional Safety Rules For Tool - Makita 5103N Instruction Manual

changing accessories. Inspect tool cord periodically
and if damaged have it repaired by an authorized
service facility. Inspect extension cords periodically
and replace, if damaged. Keep handles dry, clean and
free from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension cords
intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform its
intended function. Check for alignment of moving
parts, free running of moving parts, breakage of parts,
mounting and any other conditions that may affect its
operation. A guard or other part that is damaged
should be properly repaired or replaced by an
authorized service center unless otherwise indicated
in this instruction manual. Have defective switches
replaced by an authorized service facility. Do not use
the tool if the switch does not turn it on and off.
21. Warning.
The use of any accessory or attachment, other than
those recommended in this instruction manual or the
catalog, may present a risk of personal injury.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts,
otherwise this may result in considerable danger to
the user.
ADDITIONAL SAFETY RULES
FOR TOOL
1. Wear hearing protection.
2. Keep Guards In Place and In Working Order.
Never wedge or tie lower guard open. Check
operation of lower guard before each use.
Don't use if lower guard does not close briskly
over saw blade.
CAUTION: If saw is dropped, lower guard may be
bent, restricting full return.
3. Do not use blades which are deformed or cracked.
4. Do not use blades made of high speed steel.
5. Do not stop the blades by lateral pressure on the
saw blade.
6. Keep Blades Clean and Sharp.
Sharp blades minimize stalling and kickback.
7. DANGER:
Keep Hands Away From Cutting Area.
6
Keep hands away from blades. Don't reach
underneath work while blade is rotating. Don't
attempt to remove cut material when blade is
moving.
CAUTION: Blades coast after turn off.
8. Support Large Panels (Fig. 1 & 2).
Large panels must be supported as shown in
Fig. 1 to minimize the risk of blade pinching and
kickback.
When cutting operation requires the resting of the
saw on the workpiece, the saw shall be rested on
the larger portion and the smaller piece cut off.
To avoid kickback, do support board or panel near the
cut. (Fig. 1)
Do not support board or panel away from the cut.
(Fig. 2)
9. Use Rip Fence.
Always use a fence or straight edge guide when
ripping.
10. Guard Against Kickback. (Fig. 1 & 3)
Kickback occurs when the saw stalls rapidly and
is driven back towards the operator.
Release switch immediately if blade binds or saw
stalls. Keep blades sharp. Support large panels as
shown in Fig. 1.
Use fence or straight edge guide when ripping.
Don't force tool. Stay alert-exercise control.
Don't remove saw from work during a cut while
the blade is moving.
NEVER place your hand or fingers behind the saw.
If kickback occurs, the saw could easily jump
backwards over your hand, possibly causing
severe injury.
11. Lower guard should be retracted manually only for
special cuts such as "Compound Cuts".
Raise lower guard by Retracting Lever. As soon as
blade enters the material, lower guard must be
released. For all other sawing, the lower guard should
operate automatically.
12. Adjustments.
Before cutting be sure depth and bevel
adjustments are tight.
13. Use Only Correct Blades In Mounting.
Don't use blades with incorrect size holes.
Never use defective or incorrect blade washers or
bolts.
14. Avoid Cutting Nails.
ENB036-4
Inspect for and remove all nails from lumber
before cutting.
15. When operating the saw, keep the cord away from
the cutting area and position it so that it will not be
caught on the workpiece during the cutting
operation. Operate with proper hand support,
proper workpiece support, and supply cord
routing away from the work area.
WARNING:
It is important to support the workpiece properly
and to hold the saw firmly to prevent loss of
control which could cause personal injury. Fig. 4
illustrates typical hand support of the saw.
A typical illustration of proper hand support, workpiece
support, and supply cord routing. (Fig. 4)
16. Place the wider portion of the saw base on that
part of the workpiece which is solidly supported,