List Of Simulation Codes - Sharp MX-2300 G Service Manual

2. List of simulation codes

Code
Main Sub
1 1 Used to check the operations of the scanner unit and its control circuit.
2 Used to check the operation of sensor and detector in the scanning (read)
section and the related circuit.
5 Used to check the operations of the scanner unit.
2 1 Used to check the operations of the automatic document feeder unit and the
control circuit.
2 Used to check the operations of the sensors and detectors in the automatic
document feeder unit and the related circuits.
3 Used to check the operations of the loads in the automatic document feeder unit
and the control circuits.
3 2 Used to check the operation of sensor and detector in the finisher and the
related circuit.
3 Used to check the operation of the load in the finisher and the control circuit.
10 Used to adjust the finisher.
4 2 Used to check the operations of the sensors and detectors in the desk/large
capacity tray and the related circuit.
3 Used to check the operations of the loads in the large capacity tray and the
related circuit.
5 Used to check the operations of the clutches and the related circuits.
5 1 Used to check the operation of the display, LCD in the operation panel, and
control circuit.
2 Used to check the operation of the heater lamp and the control circuit.
3 Used to check the operation of the scanner lamp and the circuit.
4 Used to check the operation of the discharge lamp and the related circuit.
6 1 Used to check the operations of the paper transport system, the transfer system,
the fusing system (clutches and solenoids) and the control circuits.
2 Used to check the operations of each fan motor and its control circuit.
3 Used to check the operations of the primary transfer unit and the related circuit.
7 1 Used to set the operating conditions of aging.
6 Used to set the intermittent aging cycle.
8 Used to display the warm-up time.
9 Used to check printing in the color mode.
8 1 Used to check and adjust the operations of the developing voltage of each color
and the control circuit.
2 Used to check and adjust the operation of the main charger grid voltage in each
printer mode and the control circuit.
6 Used to check and adjust the operation of the transfer voltage and the control
circuit.
9 2 Used to check the operations of the sensors and detectors in the duplex section
and its control circuit.
3 Used to check the operations of the loads in the duplex section and the control
circuits.
10 1 Used to check the operations of the toner motor and the related circuit.
13 -- Used to cancel the self-diag "U1" trouble.
14 -- Used to cancel excluding the self-diag U1/LCC/U2/PF troubles.
15 -- Used to cancel the self-diag "U6-09" (large capacity paper feed tray) trouble.
16 -- Used to cancel the self-diag U2 trouble.
17 -- Used to cancel the self-diag PF.
21 1 Used to set the maintenance cycle.
22 1 Used to check the print count value in each section and each operation mode.
(Used to check the maintenance timing.)
2 Used to check the total numbers of misfeed and troubles. (When the number of
total jam is considerably great, it is judged as necessary for repair.)
3 Used to check misfeed positions and the misfeed count of each position.
4 Used to check the trouble (self diag) history.
5 Used to check the ROM version of each unit (section).
6 Used to output the list of the setting and adjustment data (simulations, FAX soft
switch, counters).
8 Used to check the number of use of the finisher, the RSPF, and the scan
(reading) unit.
9 Used to check the number of use (print quantity) of each paper feed section.
Function (Purpose)
MX-2300/2700 N/G SIMULATION 7 – 3
Section
Optical (Image scanning) Operation test/check
Optical (Image scanning) Operation test/check
Optical (Image scanning) Operation test/check
RSPF Operation test/check
RSPF Operation test/check
RSPF Operation test/check
Finisher Operation test/check
Finisher Operation test/check
Finisher Adjustment
Desk/Large capacity tray Operation test/check
(LCC)
Desk/Large capacity tray Operation test/check
(LCC)
Desk/Large capacity tray Operation test/check
(LCC)
Operation panel Operation test/check
Fusing Operation test/check
Optical (Image scanning) Operation test/check
Process Operation test/check
Paper transport section Operation test/check
(Transport, paper exit)
Other Operation test/check
Process (Transfer) Operation test/check
Other Setting
Other Setting
Fusing Operation display
– Operation test/check
Process (Photoconductor/ Operation test/Check/
Developing/Transfer/ Adjustment
Cleaning)
Process (Photoconductor/ Operation test/Check/
Developing/Transfer/ Adjustment
Cleaning)
Process (Photoconductor/ Operation test/Check/
Developing/Transfer/ Adjustment
Cleaning)/Transfer
Duplex Operation test/check
Duplex Operation test/check
Process (Developing) Operation test/check
FAX Clear/cancel (Trouble etc.)
– Clear/cancel (Trouble etc.)
LCC Clear/cancel (Trouble etc.)
MFPcnt PWB / PCU PWB Clear/cancel (Trouble etc.)
/ SCU PWB
Communication unit (RIC/ Clear/cancel (Trouble etc.)
MODEM)
– Setting
– Adjustment/Setup/Operation
data check
– Adjustment/Setup/Operation
data check
– Adjustment/Setup/Operation
data check
– Adjustment/Setup/Operation
data check
– Others
– Adjustment/Setup/Operation
data check
– Adjustment/Setup/Operation
data check
Paper feed, ADU Adjustment/Setup/Operation
data check
Purpose