Cisco TelePresence SX20 Administrator's Manual page 119

Cisco TelePresence SX20 Quick Set
Contents
Video OSD Output
Define on which monitor the on-screen menus, information and icons should be displayed. The
OSD (On Screen Display) is where you find the menus, dialogs, icons and indicators, and the
navigation is done with a remote control.
Requires user role: ADMIN
Value space: <Auto/1/2>
Auto: The system will detect when a monitor is connected to the video output, and send the
OSD to the first monitor you connect. If you have a multi-monitor setup, and all monitors are
connected before switching on the system, the OSD will be sent to the video output with the
lowest numbering, starting on Video OSD Output 1. If the OSD does not show on the desired
monitor, disconnect all monitors and reconnect the monitors.
Range 1-2: If you want the OSD to be sent to one specific output, select 1 for HDMI output,
or select 2 for DVI-I output. Make sure you connect a monitor to the corresponding video
output connector.
Video OSD Output: Auto
Example:
Video OSD InputMethod InputLanguage
The codec can be enabled for Cyrillic input characters in the menus on screen. Requires that
Video OSD InputMethod Cyrillic is set to On.
Requires user role: ADMIN
Value space: <Latin/Cyrillic>
Latin: Latin characters can be entered when using the remote control (default).
Cyrillic: Cyrillic characters can be entered using the remote control. Requires a Cisco
TelePresence Remote Control with Cyrillic fonts.
Video OSD InputMethod InputLanguage: Latin
Example:
Video OSD InputMethod Cyrillic
Set the Cyrillic mode for the menu input language in the menus on screen.
Requires user role: ADMIN
Value space: <Off/On>
Off: Cyrillic mode is NOT available as a menu input language in the menus on screen.
On: Cyrillic mode is available as a menu input language in the menus on screen. This will
enable the setting Video OSD InputMethod InputLanguage.
Video OSD InputMethod Cyrillic: Off
Example:
D14908.10 SX20 Administrator Guide TC7.3, JULY 2015.
Introduction Web interface System settings System settings
Video OSD LoginRequired
Determine if the system should require the user to login before accessing the menus on screen.
If enabled, the user must enter his username and his PIN code. After the user has logged in
he can only execute to the configurations changes and commands allowed by his role. The
OSD (On Screen Display) is where you find the menus, dialogs, icons and indicators, and the
navigation is done with a remote control.
NOTE: The PIN code must be set before enabling this setting, this is done from a web interface.
Login to the system from a web browser, navigate to Configuration > User Administration, select
the user and add the PIN code.
Requires user role: ADMIN
Value space: <Off/On>
Off: No login to the menus on screen (OSD) is required.
On: The user must log in to access the menus on screen (OSD).
Video OSD LoginRequired: Off
Example:
Video Output HDMI [1,2] Location HorizontalOffset
HorizontalOffset and VerticalOffset settings are associated with each video output. These
settings are used to signal the relative position of the displays that are connected to these
outputs.
HorizontalOffset = 0 and VerticalOffset = 0 indicates that the display is positioned in center,
both horizontally and vertically. A negative horizontal offset indicates that the monitor is left of
center, and a positive horizontal offset indicates that the monitor is right of center. A negative
vertical offset indicates that the monitor is below center, and a positive vertical offset indicates
that the monitor is above center. The magnitude of the offset indicates how far the display is
from center (relative to other displays).
Example: You have two displays side by side, one in center and one to the left. Then the
following settings will apply: HorizontalOffset = 0 for the center display, HorizontalOffset = -1 for
the left display.
Example: You have two displays, one in center and one below. Then the following settings will
apply: VerticalOffset = 0 for the center display, Vertical Offset = -1 for the lower display.
The default values for the different outputs are:
Video Output HDMI [1] Location: HorizontalOffset = 0, VerticalOffset = 0
Video Output HDMI [2] Location: HorizontalOffset = 1, VerticalOffset = 0
Requires user role: ADMIN
Value space: <-100..100>
Range: The value must be between -100 and 100.
Video Output HDMI 1 Location HorizontalOffset: 0
Example:
www.cisco.com — Copyright © 2012-2015 Cisco Systems, Inc. All rights reserved.
119
Administrator Guide
Setting passwords Appendices