Specifications; Specific Safety Rules - Makita 3707 Instruction Manual

ENGLISH
1 Loosen
2 Tighten
3 Hold
4 Base
5 Adjusting roller
6 Bit protrusion
7 Lever
8 Scale
9 Switch lever
10 Workpiece
11 Feed direction
12 Bit revolving direction
13 View from the top of the tool

SPECIFICATIONS

Model
Collet chuck capacity....................................................................6 mm or 1/4"
-1
No load speed (min )...................................................................35,000
Overall length ...............................................................................204 mm
Net weight.....................................................................................1.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to trimmer safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal injury.
1. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the oper-
ator.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of con-
trol.
3. Wear hearing protection during extended period
of operation.
4. Handle the bits very carefully.
Explanation of general view
14 Correct bit feed direction
15 Trimmer shoe, straight guide
or trimmer guide
16 Bolt
17 Guide plate
18 Straight guide
19 Flat washer
20 Wave washer
21 Wing nut
22 Clamp screw (A)
23 Centre hole
24 Nail
25 Adjusting screw
5.
6.
7.
8.
9.
10. Before using the tool on an actual workpiece, let
11. Be careful of the bit rotating direction and the
12. Do not leave the tool running. Operate the tool
13. Always switch off and wait for the bit to come to
14. Do not touch the bit immediately after operation;
15. Do not smear the tool base carelessly with thin-
16. Draw attention to the need to use cutters of the
17. Some material contains chemicals which may be
18. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
26 Clamp screw (B)
27 Trimmer guide
28 Bit
29 Guide roller
30 Screwdriver
31 Base protector
32 Screws
33 Straight bit
34 Templet
35 Distance (X)
36 Templet guide 10
37 Limit mark
38 Brush holder cap
3707/3707F
Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
it run for a while.
Watch for vibration or wobbling that could indi-
cate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
ner, gasoline, oil or the like.
They may cause cracks in the tool base.
correct shank diameter and which are suitable
for the speed of the tool.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
the material and application you are working
with.
3707FC
6 mm or 1/4"
26,000
204 mm
1.2 kg
5