Makita GA7050 Instruction Manual
Hide thumbs
Also See for GA7050:
- Instruction manual (104 pages) ,
- Technical information (8 pages) ,
- Instruction manual (80 pages)
Related Manuals for Makita GA7050
Summary of Contents for Makita GA7050
- Page 1 INSTRUCTION MANUAL Angle Grinder GA7050 GA7050R GA9050 GA9050R 010638 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Specifications
Work mode : surface grinding Vibration emission (a ) : 5.5 m/s h,AG Uncertainty (K) : 1.5 m/s For Model GA7050, GA9050 ENF100-1 Work mode : disc sanding For public low-voltage distribution systems of Vibration emission (a ) : 2.5 m/s h,DS between 220 V and 250 V. - Page 3 Power tool plugs must match the outlet. Never Makita Corporation responsible modify the plug in any way. Do not use any manufacturer declare that the following Makita adapter plugs with earthed (grounded) power machine(s): tools. Unmodified plugs and matching outlets will Designation of Machine: reduce risk of electric shock.
-
Page 4: Grinder Safety Warnings
Personal safety dangerous in the hands of untrained users. Stay alert, watch what you are doing and use 22. Maintain power tools. Check for misalignment common sense when operating a power tool. or binding of moving parts, breakage of parts Do not use a power tool while you are tired or and any other condition that may affect the power tool’s operation. - Page 5 controlled. accessory could snag your clothing, pulling the The arbour size of wheels, flanges, backing accessory into your body. pads or any other accessory must properly fit 14. Regularly clean the power tool’s air vents. The the spindle of the power tool. Accessories with motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal arbour holes that do not match the mounting...
- Page 6 Safety Warnings Specific for Grinding and Abrasive e) Support panels or any oversized workpiece Cutting-Off Operations: to minimize the risk of wheel pinching and a) Use only wheel types that are recommended kickback. Large workpieces tend to sag under for your power tool and the specific guard their own weight.
-
Page 7: Functional Description
25. Do not touch the workpiece immediately after FUNCTIONAL DESCRIPTION operation; it may be extremely hot and could burn your skin. 26. Always be sure that the tool is switched off CAUTION: and unplugged or that the battery cartridge is Always be sure that the tool is switched off and •... - Page 8 For tool with the lock-off switch Installing side grip (handle) To prevent the switch trigger from accidentally pulled, a lock lever is provided. CAUTION: To start the tool, push in the lock lever (in the A direction) Always be sure that the side grip is installed •...
- Page 9 For tool with clamp lever type wheel guard WARNING: Never use a more than 6.5 mm thick grinding • 1. Wheel guard wheel. 2. Bearing box 3. Nut Super flange 4. Lever Models with the letter F are standard-equipped with a super flange.
-
Page 10: Operation
ALWAYS replace wheel if tool is dropped while • 010844 Mount inner flange , abrasive wheel/Multi-disc and grinding. Ezynut onto the spindle so that Makita Logo on Ezynut NEVER bang or hit grinding disc or wheel onto • faces outside. work. - Page 11 ALWAYS hold the tool firmly with one hand on rear 1. Wire wheel handle and the other on the side handle. Turn the tool on brush and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface.
-
Page 12: Maintenance
2. Inhalation vent injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. 010653... - Page 13 Side grip Wheel guard for Depressed center grinding wheel / Multi disc / Wire wheel brush Inner flange / Super flange / Inner flange 102 (Australia and New Zealand only) Depressed center grinding wheel/Multi-disc Lock nut / Ezynut*1 Wheel guard for Abrasive cut off wheel / Diamond wheel*2 Inner flange / Super flange / Inner flange 78 (Australia and New Zealand only) Abrasive cut off wheel / Diamond wheel Outer flange 78 (Australia and New Zealand only)*3...
- Page 16 Makita Corporation Anjo, Aichi, Japan www.makita.com 884937B223...