This manual describes all the procedures that are required to start operation of the FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system. This manual is intended for use of FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system in re- gions other than Japan.
This chapter describes the settings required to operate Advanced Copy. • "Chapter 10 System Status Check" (page 168) This chapter describes the status check for the FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system after system configuration. "Chapter 11 Solution Configuration" (page 174) •...
Page 5
"ETERNUS DX100 S3" refers to the FUJITSU Storage ETERNUS DX100 S3 Disk storage system and "ETERNUS • DX200 S3" refers to the FUJITSU Storage ETERNUS DX200 S3 Disk storage system. "ETERNUS DX Disk storage system" refers to the ETERNUS DX100 S3 and ETERNUS DX200 S3 Disk storage • systems.
Page 6
The black "Must Do..." circle indicates actions that must be taken. The required ac- tion is both illustrated inside the black disk and written above it (e.g. Unplug). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 7
- Do not use alcohol or other solvents to clean the ETERNUS DX Disk storage system. Warning layout ribbon FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 8
Manufacturer’s label The model name and the serial number are listed. Device ID label The model name and the serial number are listed. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 9
Preface Drive Enclosures • 2.5" type drive enclosure 3.5" type drive enclosure • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 11
• Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U) Manufacturer’s label Information such as the model name and serial number is indicated. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 17
Table 7.1 ETERNUS DX Disk Storage System Operation According to the Settings of the Auto Power Function and the Power Resume Function........................121 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
This section provides the names of the components in the front of a controller enclosure. ■ 2.5" Type Figure 1.1 Front View of a 2.5" Type Controller Enclosure Operation panel 2.5" drive Flange cover FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Host interface (CA#0) Drive interface (OUT) port LAN (RMT) port Host interface (CA#1) LAN (MNT) port Power supply unit (PSU#0) 10. Power supply unit (PSU#1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
10. Power supply unit (PSU#1) Controller (CM#0) Controller (CM#1) PWC port Host interface (CA#0) Drive interface (OUT) port LAN (RMT) port Host interface (CA#1) LAN (MNT) port FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Figure 1.8 Rear Views of a Drive Enclosure (When Only One I/O Module is Installed) I/O module (IOM#0) Cover Drive interface (IN) port Drive interface (OUT) port Power supply unit (PSU#0) Power supply unit (PSU#1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Drive interface (IN) port Drive interface (OUT) port Power supply unit (PSU#0) Power supply unit (PSU#1) Power supply unit (PSU#2) Power supply unit (PSU#3) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 12Outlets) There are 12 outlets. Figure 1.12 Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 12Outlets) Main line switch Outlet (OUTPUT) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 16Outlets) There are 16 outlets. Figure 1.13 Power distribution unit for DX100 S3/DX200 S3 (AC200-240V, 2U, 16Outlets) Main line switch Outlet (OUTPUT) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Contact your sales representative or maintenance engineer if drives that are instal- led by default need to be uninstalled or moved to another slot. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
This section describes how to install the power distribution unit in a rack. Do Not • Do not connect any devices other than the ETERNUS DX Disk storage system to the power distribution unit. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
3rd hole (M6 screw) (M6 screw) Power distribution unit 1st hole 1st hole (M6 screw) (M6 screw) Power distribution unit base line Bracket FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 29
The blank panel should be attached at the same height as the power distribution unit. Blank panel (Rack pillar: front) Power distribution unit (Rack pillar: rear) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Attachment procedure Clip the M5 cage nut tabs into the desired hole from the inside. Side view M5 cage nut Rack pillar (square hole) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 31
The blank panel should be attached at the same height as the power distribution unit. Blank panel Power distribution unit (Rack pillar: front) (Rack pillar: rear) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Use the two plates to fasten the rack rails to the front rack pillars. Use the four washers to fasten the rack rails to the rear rack pillars. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 33
(M5 screw) (M5 screw) Controller enclosure base line Rack rail Tighten the M4 screws of the rack rails that were slightly unscrewed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 34
Fasten the controller enclosure in the rack. Use three M5 screws to fasten it in the rack pillar. M5 screw M5 screws Attach the flange cover. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
An "L" mark is on the inner side. [Left] (Rack pillar: front) Rack rail (right) An "R" mark is on the inner side. [Right] FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 36
(M5 screw) Bottom position of drive enclosure Rack rail Tighten the M4 screws of the rack rails that were slightly unscrewed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 37
Fasten the drive enclosure in the rack. Use four M5 screws to fasten it in the rack. M5 screws M5 screws Attach the flange cover. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Rack rail (left) "Left" is on the exterior [Right] Rack rail (right) "Right" is on the exterior (Rack pillar: front) (Rack pillar: rear) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 39
M4 screw (right) (Rack pillar: front) The M4 screw positions for the rack rails are determined by the high-density drive enclosure base line. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 40
Insert the M5 screws in the seventh holes above the base line to fasten the stopper brackets. High-density drive enclosure Front [Left] [Right] 7th hole 7th hole (M5 screw) (M5 screw) High-density drive enclosure base line Rack rail FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 41
Install the high-density drive enclosure in the rack. To keep it safe and stable, use a lifter to install or remove high-density drive • enclosures in racks. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 42
To attach the cable management arm, place the arm in the bracket on the rear of the high-density drive enclosure. After placing the arm in the bracket, firmly attach the arm with the pin. Cable management arm FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 43
Chapter 2 Rack Installation High-density Drive Enclosure Installation (for Regions Other than EMEA&I) Attach the front cover. Front cover FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Multipath iSCSI SAN Remote support center LAN for Operation Management SNMP manager PC for Operation Management/ PC for setup Mail server Syslog server FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
ETERNUS DX Disk storage system. If the server is connected, shut down the server, remove the cable, and then restart the server. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
To change the installation directory, click the [Browse] button and select the directory to install. To leave the settings unchanged, click the [Next] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
For the first startup, the dialog box that are shown below appears. If there is no problem with service startup settings, click the [Yes] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 48
Chapter 3 Checking the Configuration Environment Server Connection Preparation On the [iSCSI Initiator Properties] screen, click the [Configuration] tab. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 49
To use the default initiator name, also click the [Change] button. This allows you to continue to use this initiator name even after changing the "server name". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
IP address: 192.168.1.2 Subnet mask: 255.255.255.0 Check the settings of the Web browser. For details on the required settings, refer to "Configuration Guide (Web GUI)". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Enter the IP address for the RMT port of the ETERNUS DX Disk storage system. The RMT port is a LAN port that is used during initial setup and to connect to the remote support center. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
— ´ ´ KMIP (key manage- 5696 ¡ (*2) ¡ (*2) — ment ) (*3) ¡: Possible △: Partially possible ´: Not possible FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 53
The default LAN operation mode is "Auto Negotiation" which allows the ETERNUS DX Disk storage system to automatically recognize 1000Base-T/100Base-TX/10Base-T and Full/Half-Duplex connections. However, some devices may require that a fixed communication mode be set. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
This section uses a controller enclosure with two controllers as an example to explain the connection pro- cedure. When one controller is installed, only Controller 0 (CM#0) has to be installed. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
The last ports nearest to the edge are the DI (OUT) port of I/O module 0 in the drive enclosure of the largest DE-ID and the DI (OUT) port of I/O module 1 in the drive enclosure of the smallest DE-ID. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Connection configuration between Connection configuration between Controller 0 and the I/O module line 0 Controller 1 and the I/O module line 1 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 57
Clamp belts Flap bracket Clamp belts Cable management arm FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 58
1 and connecting drive enclosure 1 to drive enclosure 2. • When only one controller is installed Drive enclosure 2 Drive enclosure 1 Controller enclosure FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 59
Carefully check the connection origin and connection destination, and then attach the destination labels. Drive enclosure number IOM (I/O module) number DE01 0 CM (controller) number C M 0 0 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 60
Connect the DI (OUT) port of I/O module 0 (IOM#0) in drive enclosure 1 to the DI (IN) port of I/O module 0 (IOM#0) in drive enclosure 2 with the cable between enclosures. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 61
Connect the DI (OUT) port of I/O module 1 (IOM#1) in drive enclosure 2 to the DI (IN) port of I/O module 1 (IOM#1) in drive enclosure 1 with the cable between enclosures. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
The high-density drive enclosure has four power supply units (PSU#0, PSU#1, PSU#2, and PSU#3). Make sure that power cords are connected to all power supply units. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Connect the power cord to the ETERNUS DX Disk storage system. Connect the power cord plugs to the power inlets of the power supply units. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
To help with power cord management and prevent incorrect connections, attach labels to the power cords and make a note of connection origins and destinations. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 65
Power distribution unit Use the power cord clamps to prevent the power plugs from coming unplugged. Attach the power cord clamps removed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
The procedures to connect the power supply unit is same as Step 1 "4.4.1 When No Power Distribu- tion Units are Installed" (page 63). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 67
: Connect OUTPUT#0-n of the power distribution unit to the PSU#0 inlet of the ETERNUS DX Disk storage system. : Connect OUTPUT#1-n of the Power distribution unit to the PSU#1 inlet of the ETERNUS DX Disk storage system. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 68
: Connect OUTPUT#1-n of the Power distribution unit to the PSU#1 inlet of the ETERNUS DX Disk storage system. Use the power cord clamps to prevent the power plugs from coming unplugged. Attach the power cord clamps removed in Step FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 69
#0 side and the power distribution unit #1 side to different power sources. AC input cables Power distribution unit#1 Power distribution unit#0 Connect to power outlets. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Perform the basic settings to use the Advanced Copy function. For details on these settings and performing SnapOPC+, refer to "Chapter 9 Advanced Copy Settings" (page 157). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Sunday data ETERNUS DX Disk storage system SnapOPC+ By mounting the copy destination volumes, the past data is recognized as drives by the server FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
LAN cable (for operation management). For the setup information of the PC terminal, refer to "3.3 Preparing the PC Terminal for Setup" (page 50). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
● For 1U Figure 5.4 ON Position (Marked "|") of the Main Line Switches on a 1U Power Distribution Unit Main line switch FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Power supply unit (PSU#1) AC power is supplied to an enclosure. For the controller enclosure, the POWER LED on the power supply unit blinks green. • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Controller enclosure The POWER LED ( ) of the controller enclosure and the POWER LEDs ( ) of the drive enclosures are turned on. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
To change the language, click the [Option] button and select [English] or [Japanese] in [Language]. Enter the User ID and Password. User ID: root FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
• Change User Password • Set Thin Provisioning • Register Advanced Copy License • Register SED Authentication Key • Set Network Environment • FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 78
The information that is set here is used for network management by SNMP. The name of the ETER- NUS DX Disk storage system is displayed in the login and operation screens of ETERNUS Web GUI. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 79
The [Change User Password] screen appears. Change the user password. Change the user password. Set the required items and click the [Next >>] button. A confirmation screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 80
Click the [OK] button. The Thin Provisioning is set and the change completion screen appears. Click the [Done] button. The [Register Advanced Copy License] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 81
Register the SED authentication key. When Self Encrypting Drives (SEDs) are installed in the ETERNUS DX Disk storage system, register the SED authentication key. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 82
Reboot the ETERNUS DX Disk storage system according to the dis- played message. Set the network environment. Set the ETERNUS DX Disk storage system environment for network communication. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 83
Click the [OK] button. The network environment setting is applied and the setting completion screen appears. Click the [Done] button. The [Logout] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Disable the STP function of the LAN switch port only for the ETERNUS DX Disk storage system connection or perform the Port-Fast setting. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 85
Connect the LAN cables of the MNT port to the network of the customer. If the RMT port is used for remote support, connect the LAN cable of the RMT port to the network for remote support. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Click the [System] tab on the navigation of the ETERNUS Web GUI screen. In [Category], click [Network]. The [Network] screen appears. Select the port to be set. In [Action], click [Firewall Setting]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 87
ETERNUS DX Discovery Change the setting to "Disable". Click the [Set] button. In the confirmation screen, click the [OK] button. The firewall settings are applied. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
600GB SAS disk ´ 5 Operation RAID Manual RAID5 group (copy source) Backup RAID group Manual RAID5 2TB Nearline SAS disk ´ 3 (copy destination) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 89
The [Create RAID Group] screen appears. Enter the name of the RAID group that is to be registered. Select "Manual" for "Create Mode". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 90
The RAID group is registered and the registration completion screen appears. Click the [Done] button. The screen display returns to the [RAID Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
The following screen shows the RAID group information that is displayed after the RAID group is created. Figure 5.8 RAID Group Information After Creation FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Click the [Volume] tab on the navigation of the ETERNUS Web GUI screen. The [Volumes] screen appears. In [Action], click [Create]. The [Create Volume] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 93
Then, create SDV and SDPV in the backup RAID group (RG1). For the creation procedure, refer to "5.7.3 Generation Management Volume (SDV) Creation" (page 94) "5.7.4 Temporary Work Volume (SDPV) Creation" (page 95). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
RAID Group / TPP Selection: Manual Manual Setting: RG1 Number of Volumes: 7 (*2) *1: Enter the capacity of the copy source volume during creation of SDV. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
88). Figure 5.11 Temporary Work Volume (SDPV) Creation Backup RAID group (RG1) Temporary work volume 500GB sdpv (Snap Data Pool Volume) RAID5 (2+1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 96
Click the [OK] button. The volume is created and the registration completion screen appears. Click the [Done] button. The screen display returns to the [Volumes] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
This is only available to a specified RAID group. For a RAID group that contains important data, assign "Dedicated Hot Spare" in order to preferentially use the hot spare. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 98
Select the drive that is to be registered as the Global Hot Spare and click [Assign Global HS] in [Action]. A confirmation screen appears. Click the [OK] button. The Global Hot Spare is registered and the registration completion screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 99
Select the drive that is to be registered as the Dedicated Hot Spare and click [Assign Dedicated HS] in [Action]. The [Assign Dedicated Hot Spare] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 100
The Dedicated Hot Spare is registered and the registration completion screen appears. Click the [Done] button. The screen display returns to the [Drives] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
In the [Setting based on Severity] tab screen, select the required items. On the screens that are displayed by clicking each level tab, select the required items. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Gateway IP address and the Allowable IP address (IP address of the monitoring server or the network address to which the monitoring server belongs) on the [Setup Network Environment] screen of ETERNUS Web GUI. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 103
Select [Enable] for [SNMP Function], set the required items, and click the [Set] button. Select the LAN port that was set up in Step 1 for "LAN Port used for SNMP". A confirmation screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 104
The SNMP Manager settings are applied. Check the setting completion message and click the [Done] button. The screen display returns to the [Network] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 105
The screen display returns to the [Network] screen. User setup In [Action], click [Setup SNMP User]. The [Setup SNMP Agent User] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 106
In [Action], click [Setup SNMP Trap]. The [Setup SNMP Agent Trap] screen appears. In the trap list of the [Setup SNMP Agent Trap] screen, click the [Add] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 107
Download the MIB file that is registered in the ETERNUS DX Disk storage system. In [Action], click [Download MIB File]. The [Download MIB File] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 108
The MIB file is saved. Check the setting completion message and click the [Done] button. The screen display returns to the [Network] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
In the [Notification E-Mail] tab screen, set the required items. • Select "Yes" for "Notification E-Mail". • Enter the destination e-mail address or addresses for the Destination E-Mail Address fields. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 110
This item does not need to be changed from the default value for normal operation. Click the [Set] button to apply the specified settings. A confirmation screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
To send messages in RFC5424 format to a target syslog server that supports RFC5424, select "on (RFC5424)". If this is not the case, select "on (RFC3164)". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
REMCS is not specified or is stopped. When REMCS is used, suspend the REMCS function, and then ena- ble the AIS Connect function. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
(Country Code : Country Name)". Perform the other additional settings that are required. Click the [Set] button. A confirmation screen appears. Click the [OK] button. The AIS Connect settings are applied. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
On the navigation of the ETERNUS Web GUI screen, click [System]. The [System] screen appears. In [Category], click [REMCS] in [Remote Support]. The [Support Information] tab screen of the [Remote Support] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 115
Disk storage system and the remote support center is checked. The connection check result is sent to the e-mail address that is set in "Result notification information". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
To send messages in RFC5424 format to a target syslog server that supports RFC5424, select "on (RFC5424)". If this is not the case, select "on (RFC3164)". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Register the file that was downloaded in "Download the MIB file" (Step 6) in "6.2.1 SNMP Trap Setup" (page 102) as the MIB definition file for the monitoring software. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
In the [Send SNMP Trap Test] screen, click the [Send] button. A confirmation screen appears. Click the [OK] button. The test transmission of the SNMP Trap is performed. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
The [System] screen appears. In [Category], click [Network]. The [Network] screen appears. In [Action], click [Setup E-Mail Notification]. The [Setup E-Mail Notification] screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 120
Check that the test mail is sent to the e-mail addresses that are set. For details on the event code and message of the test mail, refer to "Message List". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Power Resume function is enabled The ETERNUS DX Disk storage system is automatically turned on when power is restored after a power failure. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 122
The Auto Power function and/or the Power Resume function setting is applied. Check the setting completion message and click the [Done] button. The screen display returns to the [System Settings] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
To control power supply with servers in a network to which the ETERNUS DX Disk storage system does • not belong, set "Gateway" and specify the server IP address or the network address in "Allowable IP Address". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 124
The network environment settings are applied. Check the setting completion message and click the [Done] button. The screen display returns to the [System Settings] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Click the [Connectivity] tab on the navigation of the ETERNUS Web GUI screen. On the [Connectivity] screen, click [Host Response] in [Category]. In [Action], click [Add Host Response]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
For the settings for connection using other interfaces, refer to "Configuration Guide (Web GUI)". Also refer to "Configuration Guide -Server Connection-" as required. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 127
The iSCSI host group is added and the registration completion screen appears. Click the [Done] button. The screen display returns to the [Host Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 128
• Specify [ON] to use unidirectional CHAP authentication or bidirectional CHAP authentication for the target port and [OFF] to use neither of them. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 129
The port parameter is set and the setting completion screen appears. Click the [Done] button. The screen display returns to the [iSCSI Port Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 130
The CA port group is created and the setting completion screen appears. Click the [Done] button. The screen display returns to the [CA Port Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 131
Enter the number for the first LUN and number of LUNs to allocate to the LUN group in [LUN Setting], select the number for the first volume to be allocated, and click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 132
Select the "Host Group", the "CA Port Group", and the "LUN Group" that are to be associated. Click the [Browse] button in [Host Group]. A screen to select the host group appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 133
[Host — CA Port Connection], and click the [Create] button. A confirmation screen appears. Click the [OK] button. The host affinity is created and the registration completion screen appears. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Set the CA reset group member ports and click the [Set] button. In the confirmation screen, click the [OK] button. Click the [Done] button to return to the [CA Reset Group] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
After confirming that the ETERNUS DX Disk storage sys- tem is in READY status, turn on the server. On the [iSCSI Initiator Properties] screen, click the [Discovery] tab. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 136
When setting access restrictions, the settings related to CHAP authentication is required. For details on CHAP authentication, refer to "Configuration Guide -Server Connection-". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 137
To enable mutual authentication, select [Perform mutual authentication]. Click the [OK] button. The screen display returns to the [Discover Target Portal] screen. Click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 138
On the [iSCSI Initiator Properties] screen, click the [Targets] tab. Confirm that the specified settings are correctly reflected to [The system will look for Targets on follow- ing portals]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 139
On the [iSCSI Initiator Properties] screen, click the [Targets] tab. Confirm whether the specified contents in [The system will look for Targets on following portals] have been applied correctly before checking connection. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 140
On the [Advanced Settings] screen, specify the following items under [Connect using] and click the [OK] button. Local adapter: Microsoft iSCSI Initiator Initiator IP: IP address of the server (A in Figure 8.1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 141
Target portal IP: IP address of the ETERNUS DX Disk storage system (C in Figure 8.1) Confirm that the [Add this connection to the list of Favorite Targets.] checkbox is selected and click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 142
Initiator IP: IP address of the server (B in Figure 8.1) Target portal IP: IP address of the ETERNUS DX Disk storage system (D in Figure 8.1) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 143
Chapter 8 SAN Connection Settings Server Connection Setup Confirm that [Status] of the two targets has changed to [Connected] and click the [OK] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
The following procedure explains how to check LUN using the Windows Device Manager. Open [Device Manager] and expand [Disk drives]. Confirm that the same number of "FUJITSU..." items are displayed as the number of LUNs that are set. If the example is used, eight "FUJITSU..." items are displayed.
Page 145
CM#0 CA#1 Port#0 g CAID = 20 CM#1 CA#1 Port#0 g CAID = 22 CM#0 CA#1 Port#1 g CAID = 21 CM#1 CA#1 Port#1 g CAID = 23 FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
If the [Initialize Disk] screen appears, confirm that all the disks are selected and click the [OK] button. Then proceed to Step Select the checkbox for eight disks in this example. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 147
The LUNs that are set with the ETERNUS DX Disk storage system are recognized as [Offline]. Right-click all the disks displayed as offline, and select [Online]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 148
SAN Connection Settings Server Connection Setup [Offline] changes to [Not initialized]. Right-click all the disks to be changed to online, and select [Initialize Disk]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 149
When the [Initialize Disk] screen appears, confirm that all the disks are selected and click the [OK] but- ton. Confirm that the initialized disks are displayed as [Online]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
The following procedure explains how to set up the operation disk. Select [Disk Management] from [Computer Management]. On the [New Simple Volume Wizard] screen, click the [Next] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 151
Perform the settings as shown below. File system Volume Drive that is to be Volume No. Type Capacity name created NTFS main Standard FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 152
[Format Partition] appears. Click the [Next] button. [Completing the New Simple Volume Wizard] appears. Click the [Finish] button. Check that the specified settings are displayed correctly. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 153
Set up the disk created in [Snap Data Volume]. During volume creation, right-click the disk created in [Snap Data Volume] and select [New Simple Vol- ume]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 154
Without changing the default settings of [Specify Volume Size], click the [Next] button. Assign a drive letter in [Assign Drive Letter or Path] and click the [Next] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 155
*1: The capacity that is displayed in "( )" is the copy source capacity. Select [Do not format this volume], and click the [Next] button. [Completing the New Simple Volume Wizard] appears. Click the [Finish] button. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 156
Step 7 for all the disks created in [Snap Data Volume]. In this case, seven disks are created as [Drive Letter: Assigned, RAW]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Low Priority mode. • Low Priority This mode reduces the effect on host access. Select this mode when using EC and/or OPC during operation. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 158
EC/OPC priority setting starts. In the setting completion screen, click the [Done] button. The screen display returns to the [Setting (Advanced Copy)] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
In [Action] on the [Setting] screen, click [Modify Copy Parameter]. Set the required items and click the [Set] button. In the confirmation screen, click the [OK] button. Copy table size setting starts. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
On the navigation of the ETERNUS Web GUI screen, click the [Advanced Copy] tab. In [Action], click [Create SnapOPC+]. Click the [Browse] button of the copy source volume. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 163
Select the "No.: 0, Name: main" volume. In the same way as the copy source volume, click the [Browse] button of the copy destination volume. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 164
In the confirmation screen, click the [OK] button. The SnapOPC+ session starts. Click the [Done] button to return to the [Advanced Copy] screen. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 165
In this case, the copy source volume number is "0" and the copy destination volume numbers are from "1" through to "7". Open [Disk Management] from [Computer Management]. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 166
Check if the file that was created in Step 8 "■ Operation Disk Settings" (page 150) "8.2.3.2 Disk Settings" (page 150) is displayed for the copy source drive. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 167
Old data can be restored by simply copying and pasting the data files that are to be restored from the server. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
ETERNUS DX Disk storage system. Check the status of each component on the [Storage] screen. If there is a component in Warning or Error status, contact your sales representative or maintenance engi- neer. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
GUI screen. In the [RAID Group (Basic Information)] screen that appears, select which RAID group to check the information for and click the No. or name of this RAID group. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
In the [Volume (Basic Information)] screen that appears, select which volume to check the informa- tion for and click the No. or name of this volume. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Click the [Start] button for Windows, expand [ETERNUS Multipath Driver] from [All Programs], and open [ETERNUS Multipath Manager]. Check that the LUN status is normal (that the signal icon is blue). FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Press and hold the Power switch of the controller enclosure for four seconds or more. Power switch Controller enclosure The READY LED ( ) on the controller enclosure is turned off. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 173
When a Power Synchronized Unit is Used If the server is turned off, the ETERNUS DX Disk storage system is also turned off. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
(ACM Manager). REC related settings and connection path settings must be performed in the ETERNUS DX Disk storage sys- tem. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 175
Register the replication source volumes and the replication destination volumes. For more details on the settings for ETERNUS SF AdvancedCopy Manager, refer to "ETERNUS SF AdvancedCopy Manager Operation Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Storage Cruiser responses for prioritized operations Volumes for Server A Volumes for Server C Volumes for Server B ETERNUS DX Disk storage system FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Specify the target performance value for each volume. For more details on the settings for ETERNUS SF Storage Cruiser, refer to "ETERNUS SF Storage Cruiser Opera- tion Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Business drives Backup drives ETERNUS DX Disk storage system Server Collects power consumption and temperature data for each storage system ETERNUS SF Storage Cruiser FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 179
(ETERNUS SF Storage Cruiser). For more details on the settings for ETERNUS SF Storage Cruiser, refer to "ETERNUS SF Storage Cruiser Opera- tion Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
RAID group and Thin Provisioning Pool creation Settings of a LAN for operation management (such as the firewall settings and the SSH connection set- tings) FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Install ETERNUS vCenter Plug-in in a Windows server where VMware Web Client Server is installed. Server-side settings • Install ETERNUS vCenter Plug-in and then register the ETERNUS DX Disk storage system as a management target device. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
Page 182
For more details on the settings for ETERNUS SF Storage Cruiser, refer to "ETERNUS SF Web Console Manual" and "ETERNUS SF Storage Cruiser Operation Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Create ODX volumes after enabling the ODX settings for the Advanced Copy function in the ETERNUS DX Disk storage system with ETERNUS Web GUI. For details on the SCVMM2012 settings, refer to the manual of the SCVMM2012. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED P3AM-7652-02ENZ0...
A Syslog sever is required for the destination for the transmission of the audit log that is collected. Note that ETERNUS SF KM is required when linking with the key management server. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 185
Specify the group name that is registered in the ETERNUS DX Disk storage system and the name (ma- chine ID) of the ETERNUS DX Disk storage system that is set for key management. FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 186
ETERNUS DX Disk storage system. For details on the setting procedures and setting items, refer to "ETERNUS SF KM Installation Guide". FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic) Copyright 2014 FUJITSU LIMITED...
Page 187
However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the use of information in this manual. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information •...