For your convenience, we always keep current grizzly manuals available on our website at www. grizzly.com. any updates to your machine will be reflected in these manuals as soon as they are complete.
Machine Data Sheet (G4181) Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G4181 1 HP POWER FEEDER Weight... 130 lbs. Length/Width/Height... 44 x 16 x 30 in. Foot Print (Length/Width)... N/A x N/A Type...
Page 6
No. Of Feed Speeds... 4 Feed Speeds... 13, 26, 33, 66 FPM Swing... 360 deg. Vertical Movement... 9-7/8 in. Horizontal Movement...18-1/8 in. Rotation... Forward, Reverse No. Of Rollers...3 Roller Width...2-1/4 in. Roller Diameter... 4-3/4 in. Roller Suspension... 3/4 in. Max Height Rollers Parallel Table Surface...8-1/2 in. Centers Between Rollers...5 in.
Machine Data Sheet (G7873) Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G7873 1-HP 3-PHASE POWER FEEDER Weight...130 lbs. Length/Width/Height... 44 x 16 x 30 in. Foot Print (Length/Width)... N/A x N/A Type...
Page 8
No. Of Feed Speeds... 4 Feed Speeds... 13, 26, 33, 66 FPM Swing... 360 deg. Vertical Movement... 9-7/8 in. Horizontal Movement...18-1/8 in. Rotation... Forward, Reverse No. Of Rollers...3 Roller Width...2-1/4 in. Roller Diameter... 4-3/4 in. Roller Suspension... 3/4 in. Max Height Rollers Parallel Table Surface...8-1/2 in. Centers Between Rollers...5 in.
identification refer to Figure 1 and your power feeder to familiarize yourself with the controls, features, and terminology used in this manual. doing so will make setup, use, and any future maintenance easier. Vertical travel handcrank Motor Vertical travel Upper Elbow Lock Joint Lock horizontal...
additional Safety for Power Feeders SaFEty accESSORiES. always use appro- priate machine guards. 2. tOOL SPEED. Make sure all cutting tools are rotating at the operating speed before feeding the workpiece. 3. FEEDiNG SPEED. do not overload the cutting tool by feeding too quickly. the cutting tool will perform better and be safer to work with at the rate for which it was designed.
SEctiON 2: ciRcuit REQuiREMENtS 220v Operation Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOt connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not grounded and installed in compliance with electrical...
SEctiON 3: SEtuP Setup Safety this machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- cess! -12- items Needed for...
inventory the following is a description of the main compo- nents shipped with your machine. Lay the compo- nents out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully.
G2544—Solvent cleaner & Degreaser a great product for removing the waxy shipping grease from your machine during clean up. Figure ??. Cleaner/degreaser available from grizzly. -14- you MuSt assemble all guards, fences, and holdowns before starting your machine or power feeder. Failure to heed this warning could result in serious personal injury.
base Mounting position the power feeder on the table top to determine where to drill your base mounting holes, so you can maximize power feeder swing and adjustment options. there are two mounting options available: Through Bolt Mounting and Direct Mounting (discussed on Page 16).
Mounting Options to correctly position this power feeder on your table top, completely assemble the power feeder first, then refer to this section and mount your base to the table using one of the two methods below. the reason for this order is that with the power feeder unit completely assembled, it will be easier to locate where on the table top you will need to drill your base mounting holes, so you can...
test Run once power feeder assembly is complete and mounted on the table, you must test run your power feeder to make sure it runs properly. if, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the power feeder immediately, then review the troubleshooting table on Page ???.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly industrial will not be held liable for accidents caused by lack of training. -18-...
Page 21
changing Feed Speed your power feeder has the option to feed a workpiece at 13, 26, 33, and 66 feet per minute. these rates are achieved by changing the combination of change gears, shown in Figure 12, and turning the motor switch to high or low range operation, shown in Figure 13.
SEctiON 5: MaiNtENaNcE always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Daily check: •...
SEctiON 6: SERvicE review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel- ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical support at (570) 546-9663.
Wheel Replacement always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. if you damage one or more wheels, you can easily replace the wheels. tools Needed • hex Wrench 5mm ... 1 to replace a wheel: disConnECt thE poWEr FEEdEr FroM poWEr!
Wiring Diagram Figure 17. Motor power and direction Figure 18. Motor switch and capacitor. switch. -23- READ ELECTRICAL SAFETY Model g4181/g7873 1-hp power Feeder ON PAGE ???!
PART # DESCRIPTION PSS09M SET SCREW M8-1.25 X 20 PLW04M LOCK WASHER 8MM PN03M HEX NUT M8-1.25 P4181623 OVER ARM (720MM) P4181627 RACK (650MM) PSS14M SET SCREW M8-1.25 X 12 PRP71M ROLL PIN 6 x 22 PRP31M ROLL PIN 6 x 36 P4181636 HANDWHEEL P4181649...