Page 1
Dual Projection System Dual Projection System Setup Guide Be sure to keep all user documentation handy for future reference. XJ-SK650 XJ-SK650 To obtain the latest version of this manual visit the website at the URL below. http://world.casio.com/manual/projector/ Veuillez lire les précautions dans le « Guide d’installation Français...
CASIO COMPUTER CO., LTD. shall not be held liable for any loss or lost profits due to loss of data caused by malfunction or maintenance of this product, or due to any other reason.
XJ-SK650 Overview The XJ-SK650 Projector System uses a Control Box to sync two projectors so their output looks and acts as if it is coming from a single projector. A powerful collection of projected image shaping functions, enables clear image projection not only onto a flat screen, but also onto curved and irregular surfaces.
Getting Ready Installation Location The Projector System can be placed on a flat surface or it can be ceiling mounted. Placing the Projector System on a Flat Surface When placing the Projector System on a flat surface, you need to install the four feet on the bottom of the cabinet.
Page 6
Getting Ready Location Precautions Use a conveniently located power outlet that you can reach easily when you need to unplug the power cord. Make sure there is nothing inside the area (within 30 cm Projector 30cm (11.8") (11.8 inches) of the Projector System) indicated by the nearby illustration.
Getting Ready Ceiling Installation The Projector System can be hung from a ceiling. When doing so, mount it in an inverse (upside down) configuration. Important! Important! Important! To protect against sudden accidental dropping of the Projector System from a ceiling mount configuration, be sure to secure the cabinet to ceiling fixtures with wires or some other adequate means.
Getting Ready Wiring Wire the Control Box and two projectors inside the Cabinet as shown in the illustration below. Projector A (Side nearest the Control Box) Ferrite core Use the supplied power Control Box side cord to plug into an outlet. Use a supplied RS-232C cable to connect.
Getting Ready Preparing the Remote Controllers Load two AAA-size alkaline batteries into each of the remote controllers: one YT-200 Control Box remote controller, one YT-120 projector remote controller. Batteries are provided with the Projector System. To load batteries: Open the battery cover on the back of a remote controller. Load the batteries making sure their poles (+/–) are facing in the correct directions.
Page 10
Getting Ready On the remote controller, press the [MENU] key to display the setup menu, and then configure the settings below in the indicated sequence. Setting Item Setting (1) Option Settings 1 3 Auto Keystone Correction (2) Screen Settings 3 Keystone Correction (3) Screen Settings 3 No Signal Screen Black (4) Input Settings 3 Signal Name Indicator...
Getting Ready Configuring Initial Control Box Settings After you finish configuring the initial settings of the two projectors, perform the procedure below to configure initial Control Box settings. Perform the operations below using the Control Box remote controller (YT-200). Note that these operations cannot be performed using the projector remote controller (YT-120).
Getting Ready Adjusting the Positions of the Two Projectors Use the procedure in this section to adjust the projected images of the two projectors so they are approximately the same size and at the same position on the target screen (the screen, wall, or other surface to be used as the projection surface after setup of the Projector System is complete).
Page 13
Getting Ready Perform the steps below to adjust the position and size of the Projector B image so it slightly runs off the edges of the target screen, as shown in the “After adjustment” image above. (1) Adjust the zoom ring of Projector B. (2) Loosen the five screws that secure the cabinet side panel, and then rotate the adjuster knob to adjust the orientation.
Page 14
Getting Ready On the “Image Shaping” menu that appears, select “Adjust Image Position” and then press the [ENTER] key. This will project two adjustment patterns, a yellow one for Projector A and a light blue one for Projector B. Use the focus rings of Projector A and Projector B to adjust the focus of the patterns as required. Important! Important! Important!
Page 15
Getting Ready Next, perform the procedure in the separate YA-S10 Setup Guide under “Shaping the Image to Match the Projection Screen”. Important! Important! Important! During the adjustment procedures from this point onwards, do not alter the cabinet position or positions of the projectors inside the cabinet, the zoom ring setting, the focus ring setting, or the screen position.
Product Specifications Model Name XJ-SK650 Brightness Approximately 6500 lumens Environment Operating temperature: 5 to 35°C Operating humidity: 20 to 80% (non-condensation) Operating altitude: 0 to 2,000 meters above sea level Power Requirements XJ-H2600 Projector: 100VAC 240VAC, 50/60Hz Power Consumption Each XJ-H2600 Projector: 330W (Eco Mode: Off (Bright))
Proper connectors must be used for connection to host computer and/or peripherals in order to meet FCC emission limits. Declaration of Conformity Model Number: XJ-SK650 Trade Name: CASIO COMPUTER CO., LTD. Responsible party: CASIO AMERICA, INC. Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801 Telephone number: 973-361-5400...
Page 19
Printed in China Imprimé en Chine MA1302-A RJA528057-001...