AEG PROTECT B. 750 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. AEG Manuals
  4. UPS
  5. PROTECT B. 2000
  6. Operating instructions manual

AEG PROTECT B. 750 Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

OPERATING INSTRUCTIONS UPS
PROTECT B.
PROTECT B. 750
PROTECT B. 1000
PROTECT B. 1500
PROTECT B. 2000
1
PROTECT B. 3000

Advertisement

Table of Contents
loading

Related Manuals for AEG PROTECT B. 750

Summary of Contents for AEG PROTECT B. 750

  • Page 1 OPERATING INSTRUCTIONS UPS PROTECT B. PROTECT B. 750 PROTECT B. 1000 PROTECT B. 1500 PROTECT B. 2000 PROTECT B. 3000...
  • Page 2 Thank you for purchasing a PROTECT B. UPS from AEG Power Solutions. following security advices important component of the manual and will prevent any operation errors and protect you against possible dangers. Read the manual thoroughly before you first use the appliance.

  • Page 3: Notes On These Operating Instructions

    Uninterruptible Power Supply (UPS), PROTECT B. 750, PROTECT B. 1000, PROTECT B. 1500, PROTECT B. 2000 or PROTECT B. 3000 as well as the associated external battery units PROTECT B. 1500 BP, PROTECT B. 2000 BP or PROTECT B. 3000 BP – all referred to as PROTECT B.
  • Page 4 The warranty does not apply for damage caused by non- compliance with these instructions (such damage also includes damaging the warranty seal). AEG will accept no liability for consequential damage. AEG will rescind all obligations such as warranty agreements, service contracts, etc. entered into...

  • Page 5: Table Of Contents

    Table of Contents Notes on these Operating Instructions ......3 System Description ............7 Overview ..............7 Functionality ..............8 Safety ................10 General Safety Instructions ........10 Safety Instructions for PROTECT B......10 Certification .............14 Technical Data ............15 Set-Up and Operation ............20 Unpacking and Inspection........20 Point of installation ..........21 Connections, Operation / Display Elements....22 4.3.1 Front view:............22...
  • Page 6 Interfaces and communication ........39 5.6.1 Data line protection RJ11 and RJ45 (modem / telephone / fax / network)....39 5.6.2 Computer interfaces RS232 and USB .....40 5.6.3 Communication slot (PROTECT B.1500 / B.2000 / B.3000):....40 5.6.4 Shutdown and UPS management software ..40 Signalling and failure solution.........42 LED display .............42 Audible Alarm Trouble Shooting: ......44...

  • Page 7: System Description

    System Description PROTECT B. is an Uninterruptible Power Supply (UPS) essential loads such PCs, workstations, servers, network components, telecommunication equipment and similar devices. The PROTECT B. series is a compact, interactive, sinusoidaly operating USP, available with an output power rate of 750, 1000, 1500, 2000 and 3000 VA.

  • Page 8: Functionality

    ♦ Micro processor control for high availability, suited for generator mode ♦ Easy extension of battery capacity using external batteries (starting with B.1500) ♦ Advanced battery management with integrated protection against extreme discharge and overcharge ♦ Overload and short circuit proof ♦...
  • Page 9 stabilizes the load voltage. As a result, voltage fluctuations in the public utility's mains are reduced to a level which is acceptable for the loads. This is performed without recourse to the internal energy storage, something which in turn has a positive effect on battery availability.

  • Page 10: Safety

    Safety General Safety Instructions Read these operating instructions carefully prior commissioning of the PROTECT B. UPS and observe the safety instructions! Only use the unit if it is in a technically perfect condition and always in accordance with its intended purpose, while being aware of safety and danger aspects, and in accordance with the operating instructions! Immediately eliminate any faults which could be detrimental to safety.
  • Page 11 The output may be live, even if the UPS is not connected to the mains supply, as the UPS has its own internal power supply (battery)! For health and safety reasons, the unit must be earthed correctly! PROTECT B. may only be operated with or connected to a 230 Vac mains with protective grounding using a mains connection cable with PE conductor (included in the delivery) that has been tested in accordance with German standards...
  • Page 12 ♦ Never connect the mains input to the UPS output. ♦ Ensure that no fluids or foreign bodies can penetrate the UPS! ♦ Do not block the air vents of the unit! Keep children away from the unit and ensure that objects are never inserted through the air vents! ♦...
  • Page 13 Danger! Explosive! Never throw batteries into open fire. Never open or damage batteries. (Electrolyte may leak out and damage skin and eyes. It may be toxic!) Batteries can cause electric shocks and high short-circuit currents. Therefore, take the following safety precautions when working with batteries: ♦...

  • Page 14: Certification

    Certification...

  • Page 15: Technical Data

    Technical Data Model power PROTECT B. 750 750 VA / 500 W PROTECT B. 1000 1000 VA / 700 W PROTECT B. 1500 1500 VA / 1050 W PROTECT B. 2000 2000 VA / 1340 W PROTECT B. 3000 3000 VA / 2100 W...
  • Page 16 Output current power (at 230 Vac) PROTECT B. 750 3.2 A PROTECT B. 1000 4.3 A PROTECT B. 1500 6.5 A PROTECT B. 2000 8.7 A PROTECT B. 3000 13 A Transfer time at mains outage 2-4 ms (typical), 6 ms max.
  • Page 17 24 h (UPS with 4 add. battery packs) Type Sealed, maintenance free, hot swappable (from B.1500) PROTECT B. 750 12 V / 7 Ah x 2 PROTECT B. 1000 12 V / 9 Ah x 2 PROTECT B. 1500 / B. 1500BP 12 V / 7 Ah x 4 PROTECT B.
  • Page 18 Number of outlets PROTECT B. 750 4 x IEC 320 PROTECT B. 1000 6 x IEC 320 PROTECT B. 1500 6 x IEC 320 (sep. module) PROTECT B. 2000 6 x IEC 320 (sep. module) PROTECT B. 3000 8 x IEC 320-10 A...
  • Page 19 Guidelines The PROTECT B. complies with the product norm EN 50091. The CE symbol on the unit certifies the compliance to the EG guidelines for 73/23 EEC low voltage and for 89/336 EEC electromagnetic compatibility (EMC), when following the installation instructions in the manual. For the 73/23 EEC low voltage guidelines Reference number EN 62040-1-1 : 2003...

  • Page 20: Set-Up And Operation

    AEG representative or dealer within eight days of delivery. Check the delivery is complete: ♦...

  • Page 21: Point Of Installation

    Please keep the plastic packaging bags away from babies and children in order to safeguard against suffocation accidents. Handle the components with care. Please take into account their weights. It may be necessary to engage the help of a second person, particularly in the case of the PROTECT B.

  • Page 22: Connections, Operation / Display Elements

    Connections, Operation / Display Elements 4.3.1 Front view: Model designation with type rating details PROTECT B. 750 and B. 1000 Model designation with type rating details PROTECT B. 1500 and B. 2000 (Battery module and UPS) Model designation with type rating details...

  • Page 23: Operating Panel

    4.3.2 Operating panel Explanations (see also chapter 6) 1. Main switch of the UPS (mains switch) 2. Pushbutton for system test (manually triggering) or switching off the buzzer 3. Pushbutton to view the configuration 4. Enter button 5. LED for operating mode (details on page 42) 6.

  • Page 24: Rear View (Connections)

    4.3.3 Rear view (connections): PROTECT B. 750 und 1000 Comments: 1. Mains connection (UPS input) with electric fuse and integrated spare fuse 2. Load connections (UPS outputs) 3. Surge protection (RJ11/RJ45) for data interface for phone, fax, modem or network (10/100MBit/s) 4.
  • Page 25 Comments: 1. Mains connection (UPS input) 2. Load connections (UPS outputs) PROTECT B. 3000 with additional load connection (IEC 320-16A) 3. Surge protection (RJ11/RJ45) for data interface for phone, fax, modem or network (10/100MBit/s) 4. Communication interface RS232 (9pin SUB-D socket) 5.

  • Page 26: Commissioning

    5.4 5.1.1 Tower (Stand alone deployment) All models are qualified for stand alone use. PROTECT B. 750 and 1000 consist each of only one component and can be set up either standing or lying position PROTECT B.
  • Page 27 When operating the system with more than one battery module, the UPS can be positioned between the modules. The following graphic displays the possibilities: PROTECT B. 1500 / 2000 standing and lying (standard version) PROTECT B. 3000 can be operated in the standing and lying position as well.

  • Page 28: 19" Rack Mount Setup

    Use the optional 19” mounting kit for the installation in the rack. PROTECT B. 750 und B. 1000 1. Fix the mounting ears on the side of the UPS according to the following figure. 2. Mount these subsequently to the slide assemblies.
  • Page 29 4. Add up the front panels for both sides. The mechanical installation of the UPS is completed now. PROTECT B. 1500 und B. 2000 This model is designed such that the UPS and the battery module can be mounted beside each other into the rack.
  • Page 30 1. Place the UPS on a flat and in a clean place that the front side of the UPS is facing to you. 2. Loosen the screws in the middle of the cover and remove the covers from both units. 3.
  • Page 31 6. Align the second (smaller) mounting bracket at the rear of both units and mount them with the enclosed screws. 7. Install Plug of the battery module with the socket at the rear panel of the USP. Fix the output module to the notch of the battery module.

  • Page 32: Additional Battery Installation Setup

    PROTECT B. 3000 / B. 3000 BP For mounting the 3000 VA UPS in a 19” rack fix the mounting ears to the UPS and install the unit to the rails. Do the same for the optional battery module. Additional battery installation setup PROTECT B.

  • Page 33: Emergency Power Off (Epo) Set Up

    PROTECT B. 3000 Connect the supplied battery module cable from extended battery module to the external battery port of the rear of UPS. If continuing to add up extended battery module, repeat above steps. Emergency Power Off (EPO) set up PROTECT B.

  • Page 34: Electric Start-Up

    Activate the external EPO switch to test the EPO function De-activate the external EPO switch and restart the UPS. Electric start-up First compare the setting with the rated voltage valid in your country. The factory default setting is 230 V Make any changes in accordance with the description in chapter 5.4.2 “Configuration”.

  • Page 35: Configuration

    operating stag has been reached (pos. 7 p. 3). In case anything different occurs, please follow the instructions in Chapters 6.2 / 6.3. Please shut down the entire system if you cannot solve any problems which occur. Please contact our hotline (see page 4). When the LINE MODE display is lit, switch on your loads one after the other.

  • Page 36: Operation

    6. After selecting the mode, press the confirmation button more than three seconds to complete the configuation. Operation Once you have connected the UPS to a suitable mains connection, you can start operation using the UPS main switch. On and Off switch ♦...

  • Page 37: Unit Overload

    If the UPS does not automatically return to normal operation after a few minutes, close all jobs as usual and switch off your loads (e.g. PC) before the battery is fully discharged. This lengthens the service life of the battery! Switch OFF the UPS by pressing the main switch During the discharge process as the battery capacity consistently drops, the LED BAT.MODE flashes, accompanied...

  • Page 38: System Diagnosis / Battery Test

    Also avoid short-term unit overloads, which may, for example, occur when connecting a laser printer or laser fax machine. Do not connect any household appliances to the UPS. Never connect any additional loads to the UPS if there is a mains failure, i.e. if the UPS is working in emergency power operation.

  • Page 39: Interfaces And Communication

    Executing the Test: ♦ To execute the manual check press the button about five seconds until the UPS acoustic signal fades out. ♦ Additionally the button has the function to deactivate the acoustic alarm signal. Press the button when the acoustic alarm it audible for about 1 second. The tone stops.

  • Page 40: Computer Interfaces Rs232 And Usb

    The protocol is optimized for operation with the shutdown and UPS management software “CompuWatch” from AEG. To connect to the UPS use the provided RS232 or USB cable by attaching them to a free port of your pc. RS232 interface: The interface is connected via a 9 pole Sub-D connector on the back of the unit (pos.
  • Page 41 In combination with the intelligent UPS the software ensures high availability of all IT components and full data integrity. The shutdown software “CompuWatch” supports most popular operating systems like Windows 98/ME, WindowsNT/2000/ XP, Linux, Novell Netware, IBM AIX, HP-UX, SUN Solaris, Mac OS X, ...

  • Page 42: Signalling And Failure Solution

    Signalling and failure solution LED display 1. Main switch of the UPS (mains switch) 2. Push button for manually triggering the system test or switching off the buzzer 3. Push button to view the configuration 4. Acknowledgement button 5. INPUT TYPE: LED for preselected operation state and output voltage NORMAL: (Normal mode) The LED indicator will illuminate during normal mode, the UPS accepts AC...
  • Page 43 is providing battery power to your equipment. On the other hand, the LED indicator gives you a warning which will flash every two seconds when the battery is low. LED: Bar chart LEDs showing UPS utilization. The LED indicator and the load level indicator will illuminate to show the load level;...

  • Page 44: Audible Alarm Trouble Shooting

    Audible Alarm Trouble Shooting: Problem Cause Solution Sounding every 4 The UPS is on battery Check the input voltage, seconds the input fuse resp. the circuit breaker Sounding every The battery is running low Save your work and turn second off your equipment Output overload Check load level indicator...
  • Page 45 UPS could not Output fuse it Check the output fuse provide power to the released (B. 3000) load UPS output Check the connected cable recognizes overload Ensure the load does not or short circuit exceed the maximum rating of Battery has reduced Battery is not Re-charge the battery at least backup time...

  • Page 46: Maintenance

    Maintenance PROTECT B. consists advanced resistant components. To guarantee a continuous and high availability it is recommended to check the unit (especially the batteries and the fans) in regular intervals (at least every 6 months). CAUTION: Follow safety and security regulations unconditionally! Visual control When going through the visual control check whether:...

  • Page 47: Battery Replacement

    Fan control The fan has to be checked on a regular basis for dust intrusion and strange untypical sounds. Clogged ventilation has to be cleaned. If the fan makes a strange noise or runs irregular contact the hotline (see page 4). Battery replacement CAUTION: A battery can present a risk of electrical shock...
  • Page 48 PROTECT B. 750 and B.1000 1. Unscrew the two screws on the side and remove the front panel carefully on both ends. Make sure that the panel does not tilt too much. 2. Disconnect the battery cable from the UPS and remove the battery retaining battery bracket to the right so that the battery can be pulled out to the front.
  • Page 49 5. Close and reinstall the front panel. Take care to push it in firmly and fix the front panel with the two screws from the beginning. PROTECT B. 1500 und B. 2000 1. Unscrew the two screws from the battery case and remove front panel by pulling on both ends.
  • Page 50 3. Withdraw the new batteries from the transport container and put into the right position. Fix both blocks together connect electric connections of the extracted battery system. 4. Slide the new battery carefully into shaft of the UPS until the end. 5.
  • Page 51 3. Pull first the right battery out and then the left one. 4. Withdraw the new batteries from the transport container and put into the right position. Fix both blocks together and connect the electric connections with the junction line of the extracted battery system. 5.

  • Page 52: Storage, Dismantling And Disposal

    Storage, Dismantling and Disposal Storage Long storage times without charging discharging the battery at regular intervals may lead to permanent damage of the battery. If the battery is stored at room temperature (20 C to 30 C) it will automatically discharge at a rate of 3-6 % per month due to internal reactions.

  • Page 53: Glossary

    Glossary Technical terms Automatic Voltage Regulation against mains voltage variations DC/DC Booster Circuit technology to boost the direct voltage on a higher voltage level Emergency Power Off device for emergency shut down Power Factor Correction Circuit technology to minimize circuit backfeed (important for non linear loads) Appliance protection Surge technology term...
  • Page 54 Guarantee certificate Type: …….…………………............Serial-no.: ……………………..……………....... Date of purchase: …………….....……………………..Trading stamp / Signature Specifications are subject to change without notice. AEG Power Solutions GmbH Emil-Siepmann-Straße 32 59581 Warstein-Belecke Germany Operating Instructions UPS BAL 8000015758_01 EN...

This manual is also suitable for:

A protect b. 1500Protect b. 3000Protect b. 1000Protect b. seriesProtect b. 1500

Table of Contents