Page 2
USER MANUAL FOR YOUR BAUMATIC BWD1100W Washer dryer NOTE : This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note Important safety information 5 – 6 Specifications Description of the appliance Control panel Program options LCD display Wash program selection knob Spin speed selection knob Detergent drawer Preparing the wash cycle Preparing your garments for washing A selection of wash care symbols Detergents and conditioners Program table Wash program guidance...
ENVIRONMENTAL NOTE Note : Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. Disable the door lock to make sure that children cannot get stuck inside the appliance.
General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorized service agents. Any attempt by an inexperienced person to repair the appliance, could result in injury or damage to your washing machine.
Page 6
This appliance is only designed to wash normal domestic washloads. If you use your washing machine in any other way or it is incorrectly used, then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void.
Specifications 13 wash programs/2 drying programs 6kg wash load/4kg drying load 1100 rpm maximum spin speed LCD display Electronic control Spin speed regulation via a control knob Remain time indicator 3 Option buttons: Easy iron Extra rinse Intensive wash Unbalance control system Suspend the clothes in water option Door safety lock Stainless steel drum...
Control panel Wash program selection knob This control knob allows you to select the wash program of your choice. Start/Stop button Once a wash program has been selected, this button should be pressed to start the wash cycle. Program option button This button needs to be pressed after a wash program has been selected, but before the wash program has been started.
Detergent drawer Pre wash section This compartment should have detergent placed in, if you are going to select a wash program that has a pre wash as part of it. Main wash section This compartment should have detergent placed in it (you should also put a water softening agent in this section, if you use one).
Preparing the wash cycle Preparing your garments for washing o Your washing should be sorted out, according to the fabric type and the wash care symbol that is printed on the garment’s wash care label. (see separate section on wash care symbols). o Your washing should also be sorted out according to the degree of soiling.
A selection of wash care symbols o The wash care symbols should be used to help you to select the most suitable wash program. They will also help you to sort your laundry into different loads, depending on the fabric type and the highest temperature which the garment can be washed at.
Detergents and conditioners The amount of detergent that you need to use in your appliance, will depend on o The degree of soiling. Lightly soiled garments in general require less detergent. o The size of the wash load. A smaller wash load will require a reduction in the amount of detergent.
NOTE: the KWh and litre consumptions and program durations may vary depending on the type and amount of clothes being washed, your mains water pressure, etc. (*) Program for wash and energy consumption assessment, in accordance with standard EN60456 (press intensive wash button). Wash program guidance o A particular program option can only be selected if the program table advises that it is possible with the wash cycle you have...
Selecting a wash program Load your laundry and put detergent in the relevant compartment of the soap drawer. Close the porthole door firmly. Select the most appropriate wash program for the garments that you are washing, by turning the program selector knob. o The LCD display will briefly flash the wash program number that you have selected and then show the approximate time that it will take the chosen wash cycle to complete.
o If there is a power failure or the plug is pulled out of the socket when a wash cycle is in progress. Once power has been restored, the wash program will continue. o Whilst the wash program is in progress, the time remaining to the end of the wash cycle will appear on the display.
Selecting an automatic wash and dry program Select the most appropriate wash program for the garments that you are washing, by turning the program selector knob. o The LCD display will briefly flash the wash program number that you have selected and then show the approximate time that it will take the chosen wash cycle to complete.
o It is also possible to put the machine into PAUSE status by pressing the START/STOP button whilst the wash cycle is in progress. However this will not cancel the wash program and to restart the wash cycle, you should press the START/STOP button again.
You should ensure that the garments you are washing are suitable for suspending in water before selecting this option. Garments should not be suspended in water for a prolonged period. Setting a program option o There are three program options that you can select (providing that the wash program chart indicates that a particular option can be selected with a particular wash program).
Maintenance and cleaning In daily use Once a wash cycle has completed, you should pull out the detergent drawer slightly, so it can dry out. Leave the porthole door ajar for a short while after a wash cycle has completed. This should help to prevent stagnant smells and to protect the door seal.
o Use warm water and a brush to thoroughly clean the three compartments of the detergent drawer. o Clean the area that the detergent drawer slides into with a brush. o You should also clean the siphon that sits inside of the conditioner section of the detergent drawer.
See General troubleshooting section. F05 – F10- Contact Baumatic Service Department Once the machine has been plugged back into your mains power supply, to clear the fault code from the LCD display, you should turn on the machine and hold down the Start/Stop button for approximately 5 seconds.
IF AN ENGINEER ATTENDS DURING THE GUARANTEE PERIOD AND FINDS THAT A FAULT HAS BEEN CAUSED BY AN ITEM ON THE ERROR CODE LIST, WHICH COULD HAVE BEEN CLEARED BY THE CUSTOMER. THEN YOU MAY BE LIABLE FOR THE COST OF THE SERVICE CALL. General troubleshooting Water under the washer dryer o Tighten the drain pump filter.
Poor wash results My garments are looking grey and there are limescale deposits present in the drum of my washer dryer. o There is not enough detergent being added. o The incorrect detergent is being used. o Stains are not being pre-treated. o The correct wash program or wash temperature was not selected.
Cleaning the drain pump filter IMPORTANT: Switch off your washing machine and disconnect the plug from your mains supply. You should clean out the filter approximately every twenty washes. If the drain pump filter is not cleaned regularly, then your appliance may find it difficult to pump out water efficiently.
IMPORTANT: THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERS BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL. YOU SHOULD KEEP THE TRANSIT PACKAGING, IN C YOU NEED TO TRANSPORT THE MACHINE IN THE FUTURE.
Page 29
Locate the three transit bolts that secure the drum in position, whils the appliance is being transported. Using a screwdriver, unscrew the three plastic transit bolt covers. Loosen and remove the three transit bolts. Using a screwdriver, refit the three plastic transit olt covers that you emoved previously.
ositioning and leveling the appliance Place the washing machine on a solid and level floor surface. DO NOT PLACE THE WASHING MACHINE ON A CARPET. Loosen the adjustable feet that are positioned on the base of the appliance. Slacken off the lock nut on each of the washing machine feet using a spanner.
IMPORTANT: There should be a filter sitting inside the end of the inlet hose that connects to your mains water supply. The inlet hose may leak if this filter is missing. This filter is supplied with the appliance, you should contact Baumatic to obtain one, if it is missing. Tighten th...
ater outlet Secure the drain hose, so that it cannot move whilst the washing machine is in use. Place the end of the drain hose on your drain pipe. Push it a short way down into your drain pipe. IMPORTANT: Do not insert the drain hose too deeply into the water pipe, as this may cause siphoning.
ower supply IMPORTANT: The electrical socket must still be accessible once the appliance is installed. Consult the rating plate, located on the inner rim of the porthole door of th appliance BEFORE making the electrical connections. Ensure that the vo ltage reaching the plug, is the same as th...
fore first use maintenance wash o When your washer dryer has been correctly installed, we recommend that y ou perform a maintenance wash cycle. o This will check that all aspects of the installation are corre ct; it will also remove any deposits that may have been left on the d rum by the manufacturing process.