D-Link DCS-F Series User Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Security Camera
  5. DCS-F Series
  6. User manual
D-Link DCS-F Series User Manual

D-Link DCS-F Series User Manual

Ai enabled network cameras
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
D-Link F-Series
AI Enabled
Network Cameras
User Manual
ISSUE
V 1.0
DATE
2023-02-10

Advertisement

Table of Contents
loading

Related Manuals for D-Link DCS-F Series

Summary of Contents for D-Link DCS-F Series

  • Page 1 D-Link F-Series AI Enabled Network Cameras User Manual ISSUE V 1.0 DATE 2023-02-10...

  • Page 3: About This Document

    Camera User Manual About This Document About This Document Purpose This document describes how to use the web management system, including network access, network configuration, and troubleshooting. Intended Audience This document is intended for: Technical support engineers Maintenance engineers IP camera operators Symbol Conventions The symbols that may be found in this document are defined as follows.
  • Page 4 About This Document Camera User Manual Update Version Version Update Time Description V1.0 02/2023 Support Local Server and no plugin to play live video. Issue V1.0 (2023-02-10)

  • Page 5: Table Of Contents

    Contents Camera User Manual Contents About This Document ........................i Contents ............................iii 1 Quick Start ............................1 Login and Logout ................................. 1 Change the Password ..............................2 Browse Real-Time Videos ............................3 Main Page Layout ................................. 6 Playback .
  • Page 6 Contents Camera User Manual Audio Output (Only for Some Models) ........................61 Dome PTZ (Only for Some Models) ........................62 CVBS Function (Only for Some Models) ......................63 System Service ................................. 63 Voice Denoise (Only for Some Models) ........................64 Software Licenses .
  • Page 7 Contents Camera User Manual 13 Configure the Network Service .................... 129 802.1x ..................................129 DDNS ..................................129 PPPoE ..................................131 Port Mapping ................................132 SMTP ..................................134 FTP ..................................135 IP Filter ................................... 137 CGI Alarm Service Center ............................

  • Page 9: Quick Start

    Camera User Manual Quick Start 1 Quick Start Login and Logout To access the web interface through Microsoft Edge, Chrome or Firefox browser; Otherwise some functions may be unavailable. Login Step 1 Open Microsoft Edge, enter the IP address of the IP camera (default value: 192.168.0.120) in the address box, and click on the Enter button.

  • Page 10: Change The Password

    Quick Start Camera User Manual Change the Password Description For the first login, the change default password page is as shown in Figure 1-2. Change the Default Password Page Or click to change the password to login the system, as show in Figure 1-3. Change Password Dialog Box Procedure Step 1 Input the old password, new password, and confirmation password.

  • Page 11: Browse Real-Time Videos

    Camera User Manual Quick Start The login page is displayed. Browse Real-Time Videos Download IPC Local Server If you want to play H.265 encoded video, you should download the latest IPC Local Server, as shown in Figure 1-4, when you login to the web management system for the first time. Download the Plugin Page Step 1 Click “...
  • Page 12 Quick Start Camera User Manual Select additional tasks Step 5 Tick “Create a desktop shortcut”, Click “Next” to install the plugin, as shown in Figure 1-7. Installing Step 6 Click “Finish” , complete plugin installation, as shown in Figure 1-8. Issue V1.0 (2023-02-10)
  • Page 13 Camera User Manual Quick Start Complete to Install the Plugin Step 7 Reopen the browser after installing. If the repair tips displayed when installing the control, please ignore the prompt, and continue the installation. During the plugin installing, the browser should be closed. ----End Description To browse real-time videos, click Live Video.

  • Page 14: Main Page Layout

    Quick Start Camera User Manual Live Video Page On the Live Video page, you can perform the following operations: Click to stop playing a video. Click to play a video. Double-click in the video area to enter the full-screen mode, and double-click again to exit. Configure the PTZ.
  • Page 15 Camera User Manual Quick Start Main page layout Elements on the main page No. Element Description Real-time Real-time videos are played in this page. Video Area Playback You can query the playback videos in this area. NOTE Only when the SD card or NAS has videos can you query the playback videos. People Set the query condition to query the personnel count, the statistical can be shown Counting...
  • Page 16 Quick Start Camera User Manual No. Element Description Download the latest plugin IPC Local Server. Change password, you can click to change the password. Sign Out, you can click to return to the login page. Only used for dome cameras, set PTZ parameters. Such as zoom in/zoom out, iris +/iris-, focus in / focus out, Preset / Track / Scan / Tour / Idle / Timer / Extension.

  • Page 17: Playback

    Camera User Manual Quick Start The face frame will show the snapshot of human face. The plate frame will show the snapshot of license plate. Playback Click “Playback” at web interface, if users install SD card, and there are video in SD card, click “Playback”...

  • Page 18: People Counting (Only For Some Models)

    Quick Start Camera User Manual Record backup tip Choose the type of alarm, set the start time and end time to search alarm record quickly. People Counting (Only for Some Models) At people counting interface, you can view the personnel count throughout setting query condition (choose the detail time at date’s pop-up window).
  • Page 19 Camera User Manual Quick Start People counting interface Click “Download” to download the query result. Choose the mode of showing result, such as line chart, histogram and list. Click “Query” to query the data of people counting. The data result can be saved to local folder. ----End Issue V1.0 (2023-02-10)

  • Page 20: Parameters Of Ptz

    Parameters of PTZ Camera User Manual 2 Parameters of PTZ Control and Configure the PTZ (Only for Some Models) Description All PTZ functions are only available for High Speed Network Dome and device connected to an external PTZ. The focus and zoom action can be used for motorized cameras Controlling the PTZ When browsing real-time videos shot by a dome camera or a camera connected to an external PTZ, you can control the PTZ to view videos shot in different directions.
  • Page 21 Parameters of PTZ Camera User Manual PTZ Configure area In the PTZ configure area, you can perform the following operations: Add, delete, and invoke preset positions. Add, delete, and invoke tracks. Add, delete, and invoke scans. Add, delete, and invoke tours. Set the idle.

  • Page 22: Configure And Invoke Preset Positions

    Parameters of PTZ Camera User Manual Configure and Invoke Preset Positions You can configure preset positions and quickly rotate the camera to a preset position by invoking the preset position. The procedure is as follows: Step 1 Configure a preset position. 1.

  • Page 23: Configure And Invoke Scans

    Parameters of PTZ Camera User Manual Track configuration Step 2 Invoke a track. Select a track name from the Track list, click to invoke the track. A maximum of six tracks can be configured. Configure and Invoke Scans You can configure a starting point and end point to allow the camera to repeatedly rotate from the starting point to end point.

  • Page 24: Configure And Invoke Tours

    Parameters of PTZ Camera User Manual 2. Set the scan ID and name. 3. Click 4. Use arrow keys in the PTZ Control area to set a start point and an end point. 5. Click to finish the scan setting. Step 2 Invoke a scan.

  • Page 25: Configure Idles

    Parameters of PTZ Camera User Manual Configure Idles You can enable idle to allow the camera to run the preset, track, scan and tour automatically after the waiting time (1 minute ~ 240 minutes). Step 1 Click Idle. The Idle Add page is displayed as shown in Figure 2-6. Idle configuration Step 2 Enable the Idle button.

  • Page 26: Configure Extension

    Parameters of PTZ Camera User Manual Step 3 Set the Timer Mode. Timer mode includes Everyday and Once. You should set the time when once mode is selected. Step 4 Choose Once, click Time to choose day from the pop-up calendar. Step 5 Set Timers.
  • Page 27 Parameters of PTZ Camera User Manual − Set the PTZ Type and name from the drop-down list box. − Click to finish the reboot setting. ----End Issue V1.0 (2023-02-10)

  • Page 28: Image Settings

    Image Settings Camera User Manual 3 Image Settings 3.1.1 Access the Image Settings Interface Operation Procedure: Step 1 On the web interface, enter Configuration > Image Settings interface. Image Settings Interface Step 2 Choose Debug Mode on Mode item to set the parameters. You can set four schems. ----End 3.1.2 Mode Operation procedure:...

  • Page 29: Image Setting

    Image Settings Camera User Manual Mode Page Step 2 Choose Debug Model in the middle left corner to activate the image settings page. Step 3 Tick the Enable, then set the start time and end time. Step 4 Click Save to save the setting. 3.1.3 Image Setting Figure 3-3 shows the image setting interface.
  • Page 30 Image Settings Camera User Manual Image Setting Interface Table 3-1 describes the image setting parameters. Parameters of Image Settings Parameters Parameter Description Configuration Method Brightness It indicates the total brightness of an image. As the [Setting method] value increases, the image becomes brighter. Drag the slider.

  • Page 31: Scene Mode

    Image Settings Camera User Manual Parameter Description Configuration Method Contrast It indicates the contrast between the bright part and [Setting method] the dark part of an image. As the value increases, Drag the slider. the contrast increases. [Default value] 3.1.4 Scene Mode Figure 3-4 shows the scene mode interface.

  • Page 32: Exposure

    Image Settings Camera User Manual Configuration Parameter Description Method Mirror It is used to select the pixel location of an image. [Setting method] Normal: The image does not flip. Select a value from the drop- Horizontal: The image flips to the left and down list.
  • Page 33 Image Settings Camera User Manual Exposure Interface for High-speed Dome Table 3-3 describes Exposure parameters. Parameters of Exposure Parameter Meaning Configuration Method The exposure modes include: [Setting method] Auto: The system performs auto Select a value from exposure based on the monitoring the drop-down list.
  • Page 34 Image Settings Camera User Manual Parameter Meaning Configuration Method It is used to select the metering area. [Setting method] Fulling Metering: During metering, all Select a value from areas of an image have equal weight, the drop-down list. that is, all areas are involved in the [Default value] metering.

  • Page 35: Wb Setting

    Image Settings Camera User Manual Parameter Meaning Configuration Method When the exposure Mode is Manual, you [Setting method] can set the fixed gain. Drag the slider. Fixed Gain [Default value] 3.1.6 WB Setting Figure 3-7 shows the WB Setting interface. WB Setting Interface Table 3-4 describes WB Setting parameters.

  • Page 36: Daynight

    Image Settings Camera User Manual Parameters of WB Setting Parameter Meaning Configuration Method Mode Select WB mode according to [Setting method] different scenes for better image Select a value from the drop- color reproduction. down list. Auto: In automatic white [Default value] balance (WB) mode, the Auto...
  • Page 37 Image Settings Camera User Manual DayNight Mode Interface Table 3-5 describes DayNight Mode parameters. Parameters of DNR Parameter Meaning Configuration Method D/N Setting It can be set to Auto, Day, Night or Timing. [Setting method] Mode Auto mode Select a value from the drop-down list.
  • Page 38 Image Settings Camera User Manual Parameter Meaning Configuration Method Switch The sensitivity of switching day and night. The [Setting method] Sensitivity higher value of sensitivity, and the lower light Drag the slider. intensity will switch to day. [Default value] This parameter is valid in auto mode. TRANSI.

  • Page 39: Noise Reduction

    Image Settings Camera User Manual Parameter Meaning Configuration Method [Setting method] Select a value from the drop-down list. DTN Time Time of day to night. [Default value] 18:00 [Setting method] Select a value from the drop-down list. NTD Time Time of night to day. [Default value] 6:00 Fill light settings...
  • Page 40 Image Settings Camera User Manual Noise Reduction Interface (auto) Noise Reduction Interface (manual) Table 3-6 describes DNR parameters. Parameters of DNR Parameters Parameter Meaning Configuration Method [Configuration method] Select from the drop-down list 2D NR Reduce noise of image. [Default value] Auto Issue V 1.1(2021-08-12)

  • Page 41: Enhance Image

    Image Settings Camera User Manual Parameter Meaning Configuration Method [Configuration method] Select from the drop-down list 3D NR Reduce noise of image. [Default value] Auto It is valid in auto noise filter [Setting method] mode. When the parameter Drag the slider. value is 0, the noise filter is [Default value] disabled.
  • Page 42 Image Settings Camera User Manual Enhance Image Interface Parameters of Enhance Image Parameter Meaning Configuration Method [Setting method] It is used to display the foreground and Tick the WDR background at the same time in the mode and drag the environment with a large brightness slider.

  • Page 43: Zoom Focus (Only For Some Models)

    Image Settings Camera User Manual Parameter Meaning Configuration Method The shakes and visual angle of image will [Setting method] reduce when the camera shakes slightly and the anti-shake is enable. Tick the Anti- Anti-shake shake mode. It provides a clearer view of an image in the [Setting method] fogged environment when DeFog is enabled.
  • Page 44 Image Settings Camera User Manual Issue V 1.1(2021-08-12)
  • Page 45 Image Settings Camera User Manual Zoom Focus Interface for High Speed Dome Parameters of Zoom Focus Parameter Meaning Configuration Method It is used to trigger auto focus when day to [Setting method] night or night to day. D/N Auto Focus Tick the Auto focus.
  • Page 46 Image Settings Camera User Manual Parameter Meaning Configuration Method It can be set to the auto, manual or semi- automatic mode. [Configuration Auto focus mode: The system automatically method] triggers focus based on application scenarios. Select from the Focus Mode Manual focus mode: You can trigger focus by drop-down list using the buttons on the client.

  • Page 47: Configure The Device

    Configure the Device Camera User Manual 4 Configure the Device Device Information Description The device information includes: Device ID, name, type, model, manufacturer name and MAC address. Hardware and software versions. Number of video channels, number of alarm input channels, number of alarm output channels, and number of serial ports, network cards.
  • Page 48 Configure the Device Camera User Manual Device Info Page Step 2 View the device information, set the device name according to Table 4-1. Parameters of Device Parameter Description Setting Device ID Unique device identifier used [Setting method] by the platform to distinguish The parameter cannot be modified.

  • Page 49: Video And Audio Stream

    Configure the Device Camera User Manual Parameter Description Setting Manufacturer Name Hardware Version Firmware Version Uboot version Kernel version Video Channel(s) Channel Quantity Alarm Input Quantity Alarm Output Quantity Serial Port Quantity Network card Quantity Step 3 Click If the message "Apply success!" is displayed, click OK. The system saves the settings. If the message "Apply failed!"...
  • Page 50 Configure the Device Camera User Manual Stream Configuration Page (CBR) Step 2 Set the parameters according to Table 4-2. Issue V1.0 (2023-02-10)
  • Page 51 Configure the Device Camera User Manual Parameters of Stream Configuration Parameter Description Setting Stream ID The device supports at most three main streams. [Setting method] Streams 1 and 2 adopt H.264 code. Select a value from the drop- The maximum resolution can be set for streams down list box.
  • Page 52 Configure the Device Camera User Manual Parameter Description Setting Audio Encode The following audio codec standards are supported: [Setting method] Type G711_ULAW: mainly used in North America Select a value and Japan. from the drop- down list box. G711_ALAW: mainly used in Europe and other areas.

  • Page 53: Roi Parameter

    Configure the Device Camera User Manual Parameter Description Setting Smart Encode Smart Encode. [Setting method] Smart encode includes H.264 & H.265. Click the button on to enable The storage space will be reduced fifty percent Smart Encode. when smart encode is enabled. Only main stream supports smart encode.
  • Page 54 Configure the Device Camera User Manual ROI Configuration Page Step 2 Set the parameters according to Table 4-3. Parameters of ROI Parameter Description Setting Stream Stream ID. [Setting method] Select a value from the drop- down list box. [Default value] Stream 1 Issue V1.0 (2023-02-10)

  • Page 55: Snapshot

    Configure the Device Camera User Manual Parameter Description Setting Enable the ROI Enable [Setting method] Click the button. [Default value] Area ID ROI area ID [Setting method] Select a value from the drop- down list box. [Default value] Level The visual effect of ROI. The higher the level is, the [Setting method] clearer the area is;...

  • Page 56: Local Network

    Configure the Device Camera User Manual Parameters of Snapshot Configuration Parameter Description Setting Snapshot Choose resolution of snapshot. [Setting method] Resolution Select a value from the drop- down list box. [Default value] 1280*720 Choose the quality of snapshot. Snapshot [Setting method] Quality Click the button.
  • Page 57 Configure the Device Camera User Manual Local Network Page Step 2 Set the parameters according to Table 4-5. Local Network Parameters Parameter Description Setting Network Card ID [Default value] IP Protocol IPv4 is the IP protocol that uses an address [Setting method] length of 32 bits.
  • Page 58 Configure the Device Camera User Manual Parameter Description Setting Obtain IP address The device automatically obtains the IP [Setting method] automatically address from the DHCP server. Click the button on to enable obtain IP address automatically. NOTE To query the current IP address of the device, you must query it on the platform based on the...

  • Page 59: Device Port

    Configure the Device Camera User Manual If the message "Apply success!" is displayed, and the system saves the settings. The message "Set network parameter success, Please login system again" is displayed. Use the new IP address to login to the web management system. If the message "Invalid IP Address", "Invalid Subnet Mask", "Invalid default gateway", "Invalid primary DNS", or "Invalid space DNS"...

  • Page 60: Date And Time

    Configure the Device Camera User Manual Device Port Parameters Parameter Description Setting Control Port Port used for audio and video [Setting method] transfer and signaling Enter a value manually. interaction. [Default value] 30001 HTTP Port Port used in web access. [Setting method] Enter a value manually.
  • Page 61 Configure the Device Camera User Manual Procedure Step 1 Choose Configuration > Device > Date and Time. The Date and Time page is displayed, as shown in Figure 4-7. Table 4-7 describes the parameters. Date and Time Page Date and Time Parameters Parameter Description Setting...
  • Page 62 Configure the Device Camera User Manual Parameter Description Setting Daylight When the DST start time arrives, the [Setting method] Saving Time device time automatically goes forward Click the button on to enable one hour. When the DST end time Daylight Saving Time. arrives, the device time automatically goes backward one hour.

  • Page 63: Camera

    Configure the Device Camera User Manual Click Current PC Time. Manually setting the device time − Click Set Manually. − A time setting control is displayed. − Set the date and time. Step 5 Configure the NTP. 1. Click the button on to enable NTP. 2.

  • Page 64: Osd

    Configure the Device Camera User Manual Parameter Description Setting Video Refresh The options are as follows: [Setting method] Frequency 50 Hz: corresponds to the PAL Follow the video standard. system. 60 Hz: corresponds to NTSC system. Step 2 Enter a channel name. The channel name must be within the length of 0 to 32 bytes, it is combined with digital and character (except for some special character, such as<...
  • Page 65 Configure the Device Camera User Manual PTZ OSD Page Issue V1.0 (2023-02-10)
  • Page 66 Configure the Device Camera User Manual Step 2 Set the parameters according to Table 4-9. There are at most seven OSD display areas.. OSD Parameters Parameter Description Setting Time Indicates whether to display the time. [Setting method] Tick the time. Focusing on the Displays the state of focusing on.
  • Page 67 Configure the Device Camera User Manual Parameter Description Setting Font Color Set the font color. [Setting method] Select a value from the drop- down list box. [Default value] Blank Font Size Set the font size. [Setting method] Select a value from the drop- down list box.

  • Page 68: Audio Input (Only For Some Models)

    Configure the Device Camera User Manual Audio Input (Only for Some Models) Description On the Audio Input page, you can set the audio input mode and volume. Procedure Step 1 Choose Configuration > Device > Audio Input. The Audio Input page is displayed, as shown in Figure 4-10. Table 4-10 describes the parameters. Audio Input Page Audio Input Parameters Parameter...

  • Page 69: Audio Output (Only For Some Models)

    Configure the Device Camera User Manual Audio Output (Only for Some Models) Description On the Audio Output page, you can set the audio input mode and volume. Procedure Step 1 Choose Configuration > Device > Audio Output. The Audio Output page is displayed, as shown in Figure 4-11. Table 4-11 describes the parameters. Audio Output Page Audio Output Parameters Parameter...

  • Page 70: Dome Ptz (Only For Some Models)

    Configure the Device Camera User Manual Parameter Description Setting Audio output Allows you to adjust the audio [Setting method] Volume output volume. Slide the slider left or right. [Default value] NOTE The value ranges from 0 to 100. Step 2 Click Apply. The message "Apply success!"...

  • Page 71: Cvbs Function (Only For Some Models)

    Configure the Device Camera User Manual CVBS Function (Only for Some Models) Preparation Connect a display device to the VIDEO OUT port. Description When the analog output function is enabled, the IP camera can send analog signals to a video server or display device through the VIDEO OUT port.

  • Page 72: Voice Denoise (Only For Some Models)

    Configure the Device Camera User Manual System Service Page Step 2 Select an language from the Language drop-down list box. Step 3 Click , the message "Apply success" is displayed. Step 4 Click OK, the system saves the settings. Step 5 Select a Web Mode from the Web Mode drop-down list box. Step 6 Click , the message "This operation will lead to the device to restart, continue?”...

  • Page 73: Software Licenses

    Configure the Device Camera User Manual Voice Denoise Page Step 2 Click the Voice Denoise button to enable the Voice Denoise. Step 3 Click Apply. The message "Apply success" is displayed, the system saves the setting. ----End Software Licenses Procedure Step 1 Click Configuration >...

  • Page 74: Configure External Devices

    Configure External Devices Camera User Manual 5 Configure External Devices External PTZ Parameters (Only for Some Models) Description When the IP camera is connected to an external PTZ, you can set external PTZ parameters, such as PTZ Protocol, PTZ Address, Baud Rate, and Data Bits. This function is available only for a camera connected to an external PTZ.
  • Page 75 Configure External Devices Camera User Manual PTZ Parameters Parameter Description Setting Enable this function if the device connects [Setting method] to an external PTZ. Click the button on to NOTE enable PTZ configuration. This check box is dimmed for an IP dome camera.

  • Page 76: Advanced Intelligent Analysis

    Advanced Intelligent Analysis Camera User Manual 6 Advanced Intelligent Analysis Smoke and Flame Detection Description The smoke flame detection function refers to that an alarm is generated when something is smoking or generating flame at the deployment area. Procedure Select Configuration > Advanced Intelligent Analysis > Smoke and Flame Detection to access the Smoke and Flame Detection interface, as shown in Figure 6-1.
  • Page 77 Advanced Intelligent Analysis Camera User Manual Set all parameters for Intrusion. Table 6-1 describes the specific parameters. Smoke flame detection description Parameter Description Setting Mode (only for PTZ There are two modes can be chosen, [How to set] camera) normal mode and preset point mode. Choose from the drop-down list [Default value] Normal mode...
  • Page 78 Advanced Intelligent Analysis Camera User Manual Parameter Description Setting Audible Alarm Enable, when happen the alarm, it [How to set] will be play audio to alarm. Click to enable Audible alarm Choose the sound alarm file (set at [Default value] the “Configuration >...
  • Page 79 Advanced Intelligent Analysis Camera User Manual NOTE ⚫ When you select time by dragging the cursor, the cursor cannot be moved out of the time area. Otherwise, no time can be selected. Deployment time setting interface ----End Issue V1.0 (2023-02-10)

  • Page 80: Configure Intelligent Analysis

    Configure Intelligent Analysis Camera User Manual 7 Configure Intelligent Analysis Intrusion Description The intrusion function refers to that an alarm is generated when target objects (such as person, car, and both person and car) enter the deployment area. Procedure Step 1 Select Intelligent Analysis > Intrusion to access the Intrusion interface, as shown in Figure 7-1 Intrusion Setting Interface Issue V1.0 (2023-02-10)
  • Page 81 Configure Intelligent Analysis Camera User Manual Step 2 Set all parameters of intrusion. Table 7-1 describes the specific parameters. Intrusion Parameter Description Parameter Description Setting Mode (only for There are two modes can be chosen, normal [How to set] PTZ camera) mode and preset point mode.
  • Page 82 Configure Intelligent Analysis Camera User Manual Parameter Description Setting Limit Type Enable to choose the limit type (person or car / [How to set] person / car) from type drop-down list. Click the button on. [Default value] Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm...
  • Page 83 Configure Intelligent Analysis Camera User Manual Deployment Area Setting Interface NOTE A drawn line cannot cross another one, or the line drawing fails. Any shape with 8 sides at most can be drawn. The quantity of deployment areas is up to 8. Step 4 Set deployment time Click the armed icon to set the arming time.

  • Page 84: Single Line Crossing

    Configure Intelligent Analysis Camera User Manual ----End Single Line Crossing Description A single line crossing is a line that is set at a concerned position within the monitored field of view and specifies the forbidden travel direction, an alarm is generated when target objects (such as person or car) cross this line.
  • Page 85 Configure Intelligent Analysis Camera User Manual Step 2 Set all parameters of the single line crossing. Table 7-2 describes the specific parameters. Parameters of Single Line Crossing Parameter Description Setting Mode (only for There are two modes can be chosen, normal [How to set] PTZ camera) mode and preset point mode.
  • Page 86 Configure Intelligent Analysis Camera User Manual Parameter Description Setting Limit Type Enable to choose the limit type (person or car / [How to set] person / car) from type drop-down list. Click the button on. [Default value] Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm...

  • Page 87: Double Line Crossing

    Configure Intelligent Analysis Camera User Manual Deployment Area Setting Interface NOTE Try to draw the single line crossing in the middle, because the recognition of a target takes time after target appearance on the screen and an alarm is generated only when the object is recognized to have crossed the single line crossing.
  • Page 88 Configure Intelligent Analysis Camera User Manual Double Line Crossing Setting Interface Step 2 Set all parameters of the double line crossing. Table 7-3 describes the specific parameters. Parameters of Double Virtual Fence Parameter Description Setting Mode (only for There are two modes can be chosen, normal [How to set] PTZ camera) mode and preset point mode.
  • Page 89 Configure Intelligent Analysis Camera User Manual Parameter Description Setting Limit Type Enable to choose the limit type (person or car / [How to set] person / car) from type drop-down list. Click the button on. [Default value] Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm...

  • Page 90: Multi-Loitering

    Configure Intelligent Analysis Camera User Manual also press and hold left mouse button at the endpoint of a virtual fence and move the mouse to modify the position and length of this virtual fence. You can right-click to delete the double line crossing, as shown in Figure 7-7.
  • Page 91 Configure Intelligent Analysis Camera User Manual Multi-Loitering Setting Interface Step 2 Set all parameters of multi-loitering. Table 7-4 describes the specific parameters. Multi-Loitering Parameter Description Parameter Description Setting Mode (only There are two modes can be chosen, normal mode [How to set] for PTZ and preset point mode.
  • Page 92 Configure Intelligent Analysis Camera User Manual Parameter Description Setting The Shortest The time that a target object spends in loitering [How to set] Time (Sec) cannot be less than the shortest loitering time. Input a value in the Setting range: 5-60 seconds. area box.

  • Page 93: Retrograde

    Configure Intelligent Analysis Camera User Manual Move the cursor to the drawing interface and click to generate a point, move the cursor to draw a line, and then click to generate another point. This is how a line is generated. In this way, continue to draw lines to form any shape, and right-click to finish line drawing, as shown in Figure 7-9.
  • Page 94 Configure Intelligent Analysis Camera User Manual Retrograde Setting Interface Step 2 Set all parameters of Retrograde . Table 7-5 describes the specific parameters. Retrograde Parameter Description Parameter Description Setting Mode (only There are two modes can be chosen, normal mode [How to set] for PTZ and preset point mode.
  • Page 95 Configure Intelligent Analysis Camera User Manual Parameter Description Setting Audible Enable, when the alarm happens, it will be play audio [How to set] Alarm to alarm. Click the button on. Choose the audible alarm file (set at the [Default value] “Configuration >...

  • Page 96: Illegal Parking (Only For Some Models)

    Configure Intelligent Analysis Camera User Manual Deployment Area Setting Interface NOTE A drawn line cannot cross another one, or the line drawing fails. Any shape with 8 sides at most can be drawn . The quantity of deployment areas is up to 8. Step 4 Set deployment time For more details, please refer to 7.1 Step 4.
  • Page 97 Configure Intelligent Analysis Camera User Manual Illegal Parking Setting Interface Step 2 Set all parameters for illegal parking. Figure 7-13 describes the specific parameters. Description of Parameters for Illegal Parking Parameter Description Setting Mode (only for There are two modes can be chosen, normal mode [How to set] PTZ camera) and preset point mode.
  • Page 98 Configure Intelligent Analysis Camera User Manual Parameter Description Setting Allowed Parking An alarm is generated when the object left time is [How to set] Time (Sec) longer than the shortest dwelling time. Setting range: Input a value in the 5-60 seconds. area box.

  • Page 99: People Counting (Only For Some Models)

    Configure Intelligent Analysis Camera User Manual Deployment Area Setting Interface NOTE A drawn line cannot cross another one, or the line drawing fails. Any shape with 8 sides at most can be drawn . The quantity of deployment areas is up to 8. Step 4 Set deployment time.
  • Page 100 Configure Intelligent Analysis Camera User Manual People counting Issue V1.0 (2023-02-10)
  • Page 101 Configure Intelligent Analysis Camera User Manual People counting for PTZ cameras. Step 2 Set all parameters of illegal parking. Table 7-6 describes the specific parameters. Description of Parameters for People Counting Parameter Description Setting Mode (only for PTZ There are two modes can be chosen, [How to set] camera) normal mode and preset point mode.
  • Page 102 Configure Intelligent Analysis Camera User Manual Parameter Description Setting OSD Enable Enable the OSD, the count data will show [How to set] on live video screen. Click the button on. [Default value] Counting Clear Interval The camera will clear counting data at the [How to set] setting interval.

  • Page 103: Smart Motion

    Configure Intelligent Analysis Camera User Manual Parameter Description Setting Alarm Record Enable the button to enable the alarm [How to set] record. Click to enable Alarm Record. [Default value] SMTP Enable the button to enable SMTP sever. [How to set] The parameters of SMTP can be set at Click to enable SMTP.
  • Page 104 Configure Intelligent Analysis Camera User Manual Smart Motion Setting Interface Issue V1.0 (2023-02-10)
  • Page 105 Configure Intelligent Analysis Camera User Manual Step 2 Set all parameters of smart motion. Table 7-7 describes the specific parameters. Smart Motion Parameter Description Parameter Description Setting Mode (only for There are two modes can be chosen, normal [How to set] PTZ camera) mode and preset point mode.
  • Page 106 Configure Intelligent Analysis Camera User Manual Parameter Description Setting Limit Type Enable to choose the limit type (person or car / [How to set] person / car) from type drop-down list. Click the button on. [Default value] Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm...
  • Page 107 Configure Intelligent Analysis Camera User Manual NOTE A drawn line cannot cross another one, or the line drawing fails. Any shape with 8 sides at most can be drawn. The quantity of deployment areas is up to 8. Step 4 Set deployment time Click the armed icon to set the arming time.

  • Page 108: Configure Intelligent Tracking (Only For Some Models)

    Configure Intelligent Tracking (Only for Some Models) Camera User Manual 8 Configure Intelligent Tracking (Only for Some Models) Intelligent Tracking Description This function is only used for high speed dome. Intelligent tracking is able to recognize the basic features such as the position, shape, contour and color of the target with a special algorithm.
  • Page 109 Configure Intelligent Tracking (Only for Some Models) Camera User Manual Calibration It is equivalent to a control coefficient, and real-time [Setting method] Coefficient tracking doubling rate nonlinear positive correlation; Drag the slider. Usually the higher the installation height, the greater [Default value] the calibration coefficient value;...

  • Page 110: Configure The Alarm Function

    Configure the Alarm Function Camera User Manual 9 Configure the Alarm Function Different cameras may have different alarm linkage actions. It depends on the performance of cameras, please refer to actual products. Alarm Output (Only for Some Models) Procedure Step 1 Choose Configuration > Alarm > Alarm Output. The Alarm Output page is displayed, as shown in Figure 9-1.

  • Page 111: Disk Alarm

    Configure the Alarm Function Camera User Manual Parameter Description Setting Valid Signal The options are as follows: [Setting method] Close: An alarm is generated when an Select a value from the external alarm signal is received. drop-down list box. Open: An alarm is generated when no [Default value] external alarm signal is received.

  • Page 112: Network Alarm

    Configure the Alarm Function Camera User Manual Disk Alarm Page Step 2 Click the button on to enable disk alarm. Step 3 Configure the Alarm Interval parameters. Step 4 Select Out Channel number (Please refer to the actual product). Step 5 Click Apply. The message "Apply success!"...

  • Page 113: Day Night Switch Alarm

    Configure the Alarm Function Camera User Manual Step 2 Click the button on to enable Abnormal alarm. Step 3 Configure the network alarm interval. Step 4 Select Output Channel number. You can enable alarm record when you install SD card in advance.

  • Page 114: I/O Alarm Linkage (Only For Some Models)

    Configure the Alarm Function Camera User Manual Click the armed icon to set the arming time. Click the Unarmed icon to set the unarming time. Method 1：Click left mouse button to select any time point within 0:00-24:00 from Monday to Sunday. Method 2：Hold down the left mouse button, drag and release mouse to select the deployment time within 0:00-24:00 from Monday to Sunday.
  • Page 115 Configure the Alarm Function Camera User Manual I/O Alarm Linkage Page Step 2 Select the Alarm Input value from the drop-down list box. Step 3 Enter alarm input channel name. Step 4 Select the Trigger Mode from the drop-down list box. Step 5 Click the button on to enable I/O Alarm.

  • Page 116: Motion Alarm Linkage

    Configure the Alarm Function Camera User Manual When you select time by dragging the cursor, the cursor cannot be moved out of the time area. Otherwise, no time can be selected. Schedule Setting Page Step 7 Select the Out Channel from the drop-down list box. Step 8 Select the PTZ Type from the drop-down list box.
  • Page 117 Configure the Alarm Function Camera User Manual Motion Alarm Page Step 2 Click the button on to enable motion alarm. Step 3 Configure the motion alarm interval. Step 4 Configure the Sensitivity. Tick the output channel when the camera is connected to the external alarm device.

  • Page 118: Push Message

    Configure the Alarm Function Camera User Manual Motion Area Setting Page 2. Press and hold the left mouse button, and drag in the video area to draw a detection area. Click Clear to delete a detection area. Click the red block to disarm this area. ----End Push Message Description...

  • Page 119: Audible Alarm Output (Only For Some Models)

    Configure the Alarm Function Camera User Manual The message "Apply succeed!" is displayed, and the system saves the settings. ----End Audible Alarm Output (Only for Some Models) At Configuration > Alarm > Audible Alarm Output interface, set the audio detect alarm, as shown in Figure 9-10.

  • Page 120: Abnormal Sound Detection (Only For Some Models)

    Configure the Alarm Function Camera User Manual Click to upload a new audio. The type should be WAV, size must be less than 250 Kb, the bit rate should be 128 kbps. Click “Apply” to save the settings. ----End Abnormal Sound Detection (Only for Some Models) Description The camera has mic or support the line in.

  • Page 121: Flashlight Alarm Output (Only For Some Models)

    Configure the Alarm Function Camera User Manual Audio abnormal detection Step 2 Click the button on to enable audio abnormal detection. Step 3 Enable Sudden Rise, and Sudden Drop. Step 4 Select the Output Channel. Step 5 Click the button on to enable Alarm Record. Step 6 Click the button on to enable SMTP.

  • Page 122: Whitelight Alarm Output (Only For Some Models)

    Configure the Alarm Function Camera User Manual Flashlight alarm interface Set the alarm time and flicker interval. Configure the schedule time setting. Click “Apply” to save the settings. ----End Whitelight Alarm Output (Only for Some Models) The DayNight mode is chosen Night mode, and the light is IR LED or NONE, Which is the Prerequisite, so that this linkage action is valid.
  • Page 123 Configure the Alarm Function Camera User Manual Whitelight alarm interface Set the alarm duration, it determines the duration of the whitelight on. Configure the schedule time setting. Click “Apply” to save the settings. ----End Issue V1.0 (2023-02-10)

  • Page 124: Ai Multiobject

    AI Multiobject Camera User Manual 10 AI Multiobject AI Configuration Choose Configuration > AI Multiobject to set parameter of detected face, and vehicle plate. AI Multiobject interface Issue V1.0 (2023-02-10)
  • Page 125 AI Multiobject Camera User Manual Table 10-1 lists the AI multiobject parameters. AI multiobject parameters Parameter Description How to set Face Detection The camera will snap the face when someone Enable appears in live video. Fullbody Detection The camera will snap the whole body when Enable someone appears in live video.
  • Page 126 AI Multiobject Camera User Manual Parameter Description How to set Image Matting Quality The quality of snap image, There are three mode Choose from can be chosen, such as low, mid and high. drop list. Snapshot Mode There are three mode can be chosen, such as Choose from timing, and optimal.

  • Page 127: Configure The Recording Function

    Configure the Recording Function Camera User Manual 11 Configure the Recording Function Some models may not support SD card, and the recording function is disable, please refer to actual product. Record Policy You can configure the scheduled recording function, alarm recording function, recording quality, and recording rules.

  • Page 128: Record Directory

    Configure the Recording Function Camera User Manual Recording policy parameters Parameter Description Setting Schedule Record Enables schedule record that you [Setting method] can configure the time policy. Click the button on to enable schedule record. [Default value] Alarm Post Recording duration (in seconds) [Setting method] Record (0- after an alarm is generated.
  • Page 129 Configure the Recording Function Camera User Manual Procedure Step 1 Choose Configuration > Device Record > Record Directory. The Record Directory page is displayed, there are three types to action disk, such as SD card, FTP, and NAS, as shown in Figure 11-2.. Record Directory page Step 2 Set the parameters according to Table 11-2.

  • Page 130: Configure The Sd Card

    Configure the Recording Function Camera User Manual Parameter Description Setting Alarm The camera will alarm when used Space Threshold achieves the alarm threshold. Status Status of the connection between the current camera and recording directory detected automatically. Step 3 Click Modify to modify the parameters of recording path. Record path modify ----End 11.2.1 Configure the SD Card...

  • Page 131: Configure The Ftp

    Configure the Recording Function Camera User Manual SD card Record Path Modify page Step 3 Set the parameters according to Table 11-3. SD card recording parameters Parameter Description Setting SD Card Enable SD card to enable record. [Setting method] Click button to enable SD card. Disk ID ID of SD card.
  • Page 132 Configure the Recording Function Camera User Manual FTP Record Path Modify page Step 3 Set the parameters according to Table 11-4. FTP recording parameters Parameter Description Setting Enable to use FTP (File Transfer [Setting method] Protocol) to record the video. Enable IP Address IP address of FTP server.

  • Page 133: Configure The Nas

    Configure the Recording Function Camera User Manual Step 4 Click Apply. The message "Apply success!" is displayed, and the system saves the settings. -----End 11.2.3 Configure the NAS Procedure Step 1 Choose Configuration > Device Record > Record Directory. Step 2 Choose NAS, click Modify. The NAS Record Path Modify page is displayed, as shown in Figure 11-6.
  • Page 134 Configure the Recording Function Camera User Manual Parameter Description Setting Confirm Confirm the password. [Setting method] Enter a value manually. File System There are two types can be [Setting method] chosen, cifs and nfs Choose from drop-down list. [Default value] cifs Step 4 Click Apply.

  • Page 135: Configure The Privacy Mask Function

    Configure the Privacy Mask Function Camera User Manual 12 Configure the Privacy Mask Function Procedure Step 1 Choose Configuration > Privacy Masking. The Privacy Masking page is displayed, as shown in Figure 12-1. Privacy Masking page Step 2 Click Draw to show the red frame, drag the four corners of rectangle to adjust the position. Step 3 Click Clear to delete the chosen frame.
  • Page 136 Configure the Privacy Mask Function Camera User Manual Privacy Masking parameters Parameter Description Setting ID of Privacy Masking. Name Name of privacy Masking. [Setting method] Click the name and enter a value manually. [Default value] Blank Type Type of privacy masking. [Setting method] Select a value from the drop-down list box.

  • Page 137: Configure The Network Service

    Configure the Network Service Camera User Manual 13 Configure the Network Service 802.1x Preparation 802.1x authentication must be configured on the access port, which controls to access network resources for the connected users’ devices on the port. Procedure Step 1 Choose Configuration > Network Service > 802.1x. The 802.1x page is displayed, as shown in Figure 13-1.
  • Page 138 Configure the Network Service Camera User Manual Procedure Step 1 Choose Configuration > Network Service > DDNS. The DDNS page is displayed, as shown in Figure 13-2. DDNS page Step 2 Click the button on to enable DDNS. Step 3 Set the parameters according to Table 13-1. DDNS parameters Parameter Description...

  • Page 139: Pppoe

    Configure the Network Service Camera User Manual Parameter Description Setting Host Name Host name is customized by a user. [Setting method] Enter a value manually. [Default value] Blank Accounts User name for logging in to the DDNS [Setting method] server. Enter a value manually.

  • Page 140: Port Mapping

    Configure the Network Service Camera User Manual PPPoE page Step 2 Click the button on to enable PPPoE. Step 3 Set the parameters according to Table 13-2. PPPoE parameters Parameter Description Setting PPPoE Click to enable PPPoE dialing. [Setting method] Click the button on.
  • Page 141 Configure the Network Service Camera User Manual Port Mapping page Step 2 Click the button on to enable Port Mapping. Step 3 Set the parameters according to Table 13-3. Port mapping parameters Parameter Description Setting Port Mapping Indicates whether to enable the Port [Setting method] Mapping service.

  • Page 142: Smtp

    Configure the Network Service Camera User Manual If the message "Apply success!" is displayed, and the system saves the settings. If other information is displayed, set the parameters correctly. ----End SMTP Description If the Simple Mail Transfer Protocol (SMTP) function is enabled, the device automatically sends JPG images and alarm information to specified email addresses when an alarm is generated.

  • Page 143: Ftp

    Configure the Network Service Camera User Manual Parameter Description Setting SMTP Server Port number of the SMTP [Setting method] Port server. Enter a value manually. [Default value] User Name User name of the mailbox for [Setting method] sending emails. Enter a value manually. Password Password of the mailbox for [Setting method]...
  • Page 144 Configure the Network Service Camera User Manual Procedure Step 1 Choose Configuration > Network Service > FTP. The FTP page is displayed, as shown in Figure 13-6. FTP page Step 2 Click the button on to enable FTP. Step 3 Set the parameters according to Table 13-5. FTP parameters Parameter Description...

  • Page 145: Ip Filter

    Configure the Network Service Camera User Manual Parameter Description Setting FTP Path FTP Path to save the JPG [Setting method] image. Enter a value manually. Media Type The media type of sending to [Setting method] FTP, snapshot or video clip. Select a value from the drop-down list box.
  • Page 146 Configure the Network Service Camera User Manual IP Filter page Step 2 Click the button on to enable IP Filter. Step 3 Set the parameters according to Table 13-6 IP Filter parameters Parameter Description Setting IP Filter Indicates whether to enable [Setting method] the IP Filter.

  • Page 147: Cgi Alarm Service Center

    Configure the Network Service Camera User Manual Parameter Description Setting Black List Specified network segment [Setting method] should be banned. 6. Click to enter the add black/white list page, as shown in Figure 13-8 7. Enter Begin IP Address. 8. Enter End IP Address. 9.
  • Page 148 Configure the Network Service Camera User Manual get and send to CGI Server. When need to integrate the CGI alarm message, need to resolve the HTTP Head "User-Agent" to get the data of CGI alarm message. Procedure Step 1 Choose Configuration > Network Service > CGI Alarm Service Center. The CGI Alarm Service Center page is displayed, as shown in Figure 13-9.
  • Page 149 Configure the Network Service Camera User Manual Parameter Description Setting Alarm Type All alarm types can be chosen, [Setting method] users can choose one to alarm, Select a value from the drop-down list box. or choose all. [Default value] Name Name of CGI Alarm.

  • Page 150: Snmp

    Configure the Network Service Camera User Manual ----End SNMP Description Simple Network Management Protocol (SNMP) is an Internet Standard protocol, supports SNMP v1, SNMPv2c and SNMPv3 network protocol. Choose the proper SNMP protocol version and set the SNMP protocol parameter to collect and organize information about managed devices on IP networks. Procedure Step 1 Choose Configuration >...
  • Page 151 Configure the Network Service Camera User Manual SNMP page Step 2 Click the button on to enable SNMPv1, SNMPv2C and SNMPv3. Set the parameters according to Table 13-8. Issue V1.0 (2023-02-10)
  • Page 152 Configure the Network Service Camera User Manual SNMP parameters Parameter Description Setting SNMPv1 Version of SNMP. [Setting method] SNMPv1 and SNMPv2c use communities to Click the button on. establish trust between managers and agents. SNMPv2c [Default value] Agents support three community names, write community, read community and trap.

  • Page 153: Qos

    Configure the Network Service Camera User Manual Parameter Description Setting Encrypt Encryption Algorithm, includes DES and [Setting method] Algorithm AES. Select a value from the drop-down list box. [Default value] Blank Encrypt Encryption password. [Setting method] Password Enter a value manually.

  • Page 154: Platform Access

    Configure the Network Service Camera User Manual QOS page Step 2 Input the value range from 0 to 63( audio/video dscp, alarm dscp and command dscp). Step 3 Click Apply. The message "Apply success!" is displayed, and the system saves the settings. ----End Platform Access Description...
  • Page 155 Configure the Network Service Camera User Manual Step 3 Add the IPC to platform, you should input the following information 1: IP/ID/Domain name is device ID of IPC. 2: The connection mode should be chosen Device active registration. Step 4 If you want to encrypt the access, you can enable the Encrypt. Step 5 Click Apply.

  • Page 156: Privilege Manager

    Privilege Manager Camera User Manual 14 Privilege Manager Configure a User Description You can add, modify, and delete a user in privilege manager page. Procedure Step 1 Choose Configuration > Privilege Manager > User. The User page is displayed, as shown in Figure 14-1. Table 14-1 describes the parameters. User Page User Parameters Parameter...
  • Page 157 Privilege Manager Camera User Manual Parameter Description Setting Groups Permission group where a user belongs. The [Setting method] default permission groups are Super Admin, Click Add, then select Administrators, Operator, and Media user. a value from the drop- Their permissions are described as follows: down list box.
  • Page 158 Privilege Manager Camera User Manual Function Procedure Description Modify Modify the user name, Click password, group or privilege. Modify User page displayed. Modify the user name, password, group or privilege. Click OK. The user is modified successfully. The User page is displayed. Delete Select the user from the User list.

  • Page 159: Configure Protocol Parameters

    Configure Protocol Parameters Camera User Manual 15 Configure Protocol Parameters Protocol Information Description You can view the existing protocol name and version number of the current device on the Configuration > Protocol > Protocol Info page, as shown in Figure 15-1. Table 15-1 describes the protocol-related parameters.

  • Page 160: Onvif Configuration

    Configure Protocol Parameters Camera User Manual Procedure Step 1 Choose Configuration > Protocol > Security. The Security page is displayed as shown in Figure 15-2. Table 15-2 describes the parameters on the Security page. Security Page Parameter Description Parameter Description Setting User When you select the...
  • Page 161 Configure Protocol Parameters Camera User Manual Onvif Configuration page Protocol-related parameters Parameter Description Protocol Name Type of the access protocol. Protocol Version Version number of the access protocol. Protocol Software Software version number of the access protocol. Version Profile G Enable ONVFI Profile G Intelligent Analysis Enable Intelligent Analysis Switch...

  • Page 162: Multicast Parameters

    Configure Protocol Parameters Camera User Manual Multicast Parameters Description You can set multicast IP, video port, audio port and source port in multicast parameter page. Procedure Step 1 Choose Configuration > Protocol > Multicast Param. The Multicast Param page is displayed as shown in Figure 15-4. Table 15-4 describes the parameters on the Multicast Param page.
  • Page 163 Configure Protocol Parameters Camera User Manual Parameter Description Setting Video address IP address that receive [Setting method] multicast data. Enter a value manually. [Default value] 238.255.255.255 Video Port Port that receive video [Setting method] data. Enter a value manually. [Default value] 25330 Audio Port Port that receive audio...

  • Page 164: Query Device Logs

    Query Device Logs Camera User Manual 16 Query Device Logs Query Operation Logs Description Operation logs record user operations and scheduled task commands during the running of the device. Operation logs can be classified into the following types: permission management, system maintenance, device configuration, recording operation, video control, and real-time video.

  • Page 165: Query Alarm Logs

    Query Device Logs Camera User Manual The operation logs related to the specified users are displayed. Step 4 Download the operation logs. 1. Set the start time, end time and log type. 2. Click Download on the right of the page. The log link and the message "Please download log by ’save as ‘in the right key"...

  • Page 166: Collect All Logs

    Query Device Logs Camera User Manual Step 2 Set the search criteria. 1. Click the Begin Time and End Time text boxes respectively. A time setting control is displayed. 2. Set the start time and end time as required. 3. Select the type of the alarm logs to be queried from the Alarm Type drop-down list box. Step 3 Click Query.

  • Page 167: Maintain The Device

    Maintain the Device Camera User Manual 17 Maintain the Device Restart a Device Description Restart a device including but not limited to the following situations: The device parameters are set incorrectly, and the device cannot work properly. A user needs to reset device parameters and make it to take effect. A device needs to be restarted remotely.

  • Page 168: Auto Restart

    Maintain the Device Camera User Manual Auto Restart Step 1 Choose Configuration > Maintenance. The Camera Maintenance page is displayed, as shown in Figure 17-1. Step 2 Enable the auto restart, choose the reboot interval from drop-down list. There are three option, every day/every week/every month. Camera auto restart Step 3 Click OK.

  • Page 169: Restore Device To Factory Settings

    Maintain the Device Camera User Manual Restore Device to Factory Settings Description You can restore a device to factory settings including but not limited to the following situations: The device parameters are set incorrectly, and the device cannot work properly. A user needs to reset device parameters.
  • Page 170 Maintain the Device Camera User Manual The tip will show after the configuration file uploading finish. Step 4 Click OK to finish. ----End Issue V 1.1(2023-02-10)

  • Page 171: Local Configuration

    Local Configuration Camera User Manual 18 Local Configuration Description When users download the latest IPC LocalSever, you can set folder to save the snapshots and records to local. If users use no plugin version, this function is invalid. Procedure Step 1 Choose Configuration > Local Config. The Local Config page is displayed, as shown in Figure 18-1.

  • Page 172: Troubleshooting

    Troubleshooting Camera User Manual 19 Troubleshooting Table 19-1 describes the common faults and solutions. Common faults and solutions Common Fault Possible Cause Solution When you enter the The certificate is not Click Continue to this website (not device IP address in installed.

  • Page 173: A Acronyms And Abbreviations

    Acronyms and Abbreviations Camera User Manual A Acronyms and Abbreviations ADSL Asymmetric Digital Subscriber Line Constant Bit Rate Common Gateway Interface Central Management System DHCP Dynamic Host Configuration Protocol Domain Name Server DDNS Dynamic Domain Name Server Extensible Authentication Protocol File Transfer Protocol GAMA Graphics Assisted Management Application...
  • Page 174 Troubleshooting Camera User Manual On Screen Display Phase Alteration Line Power over Ethernet PPPoE Point-to-Point Protocol over Ethernet Pan/Tilt/Zoom Region of Interest RSTP Rapid Spanning Tree Protocol SMTP Simple Mail Transfer Protocol Secure Sockets Layer Variable Bit Rate Issue V 1.1(2023-02-10)

Table of Contents