Panasonic ES-RT97 - Rechargeable Shaver Manual

Intended use

• This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean with water. The following symbol means suitable for use in a bath or shower.
  

►Notes

• Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method.
• Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged.
• If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time.
• Clean the housing only with a soft cloth slightly dampened with tap water or soapy tap water. Do not use thinner, benzine, alcohol or other chemicals.
• Store the shaver in a place with low humidity after use.
• Do not store the shaver or detergent where it will be exposed to direct sunlight or other heat sources.
• The self‑cleaning recharger cleans the inner blades and the system outer foil. Wash with water to remove beard trimmings in other areas.

Parts identification

1. Main body
   1. Protective cap
   2. System outer foil
   3. Foil frame
   4. Foil frame release buttons
   5. Thumb rest
   6. Power switch
   7. Battery capacity lamp ( )
   8. Charge status lamp ( )
   9. Appliance socket
   10. Outer foil section
   11. System outer foil release buttons
   12. Inner blades
   13. Trimmer
   14. Trimmer handle
   15. Lock release button
2. Self-cleaning recharger
   16. Arm
   17. Charging terminal
   18. Cleaning liquid unit removal button
   19. Self‑cleaning recharger socket
   20. Lock release lever
   21. Cleaning liquid filter
   22. Water maximum line
   23. Cleaning liquid unit
   24. STATUS lamp
   25. AUTO lamp
   26. SELECT button
3. AC adaptor (RE7-59)
   27. Adaptor
   28. Power plug
   29. Cord
   30. Appliance plug
4. Comb attachment
   31. Comb
   32. Trimming height window
   33. Comb attachment release buttons
   34. Trimming height switch button

Accessories

5. Special detergent (Detergent)
6. Oil

Charging the device

Charging using the self-cleaning recharger

Thoroughly wipe off any drops of water on or around the self‑ cleaning recharger so that it is dry before charging the shaver.

1. Insert the appliance plug into the self-cleaning recharger.
2. Pull up the arm until it clicks.
3. Remove the protective cap or comb attachment and then attach the shaver.
   • Turn the shaver off before attaching.
   • Check that the system outer foil is not deformed or damaged when you are attaching the shaver.
   • Put shaver into the self‑cleaning recharger with the trimmer handle retracted. If the trimmer handle is not retracted, it might scratch the cleaning tray.
4. Push down the arm unti it clicks.
5. Plug in the adaptor into a household outlet.
   • The "Charge" mode starts when attaching the shaver.
   • Check that the charge status lamp ( ) glow
   • Charging is completed after approx. 1 hour. The charging time may differ with the charging capacity.
   • Top‑up charging will not cause reductions in battery performance.
   • The appliance can be charged even with the cleaning liquid unit removed.
   • If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration.
6. Disconnect the adaptor after charging is completed.

While charging
The charge status lamp ( ) glows.

After charging is completed
The charge status lamp ( ) turns off.

Abnormal charging
The charge status lamp ( ) blinks twice every second.

• After charging is completed, turning the power switch ON with the shaver plugged in or connected to the self‑cleaning recharger will cause the charge status lamp ( ) to turn on, and then turn off after 5 seconds.
  This shows that the shaver is fully charged.
• Recommended ambient temperature for charging is 10 – 35°C (50 – 95°F). It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures.
  Charge the shaver within the recommended ambient temperature range.
• When charging the shaver for the first time or when it has not been in use for more than 6 months, the charging time may change or the charge status lamp ( ) may not glow for a few minutes. It will eventually glow if kept connected.

Charging without the self-cleaning recharger

You can also charge without the self‑cleaning recharger.

1. Insert the appliance plug into the shaver.
   • Turn the shaver off before inserting.
2. Plug in the adaptor into a household outlet.
   • Wipe off any water droplets on the appliance socket.
3. Disconnect the adaptor after charging is completed.
   • Charging the battery for more than 1 hour will not affect battery performance.

Note
You cannot operate the shaver while charging.

Using the device

1. Press the power switch.
2. Hold the shaver as illustrated and shave.
   
   • Start shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.

Notes

• Do not place your fingers on the power switch while using the shaver. This may cause the shaver to turn off. Place your fingers on the thumb rest while using the shaver.
• We recommend using the shaver in an ambient temperature range of 5 – 35°C (41 – 95°F). If used outside this range, the appliance may stop operating.

Using the trimmer

Trimming sideburns

Slide the trimmer handle up. Turn the shaver on and place at a right angle to your skin and move downwards to trim your sideburns.

• Press and hold the lock release button and slide the trimmer handle down to lower the trimmer.

Pre-shave

The trimmer can be used for a pre‑shave of long beards.

Above the lips

Turn the shaver on and place at a right angle to your skin and trim around your moustache.

Trimming the edge of beard

Cut your beard gradually with the power switch facing opposite side of your skin, taking care not to cut too much.

Using the comb attachment

Note
Apply the oil to the trimmer before and after each use.
Failure to apply the oil may cause the following problems due to rust, wear or burn out.

• The trimmer has become blunt.
• Shorter operating time.
• Louder sound.

Make sure that the shaver is turned off.

1. Mount the comb attachment to the main body until it clicks.
   
   • Press and hold the comb attachment release buttons to remove.
     
2. Slide the trimmer handle up until it clicks.
   
3. While pressing and holding the trimming height switch button, move the comb vertically to the desired trimming length (between 1 mm (1/32˝) and 7 mm (9/32˝)).
   

Trimming	mm	1.0	2.5	4.0	5.5	7.0
height (approx.)	inch	1/32	3/32	5/32	7/32	9/32
Indicator		1.0	2.5	4.0	5.5	7.0

• Actual hair length will be a little longer than the height you set.

4. Lightly push the comb attachment to ensure that it has locked into place.
   
5. Turn the shaver on, bring the comb of the comb attachment into contact with the skin, and cut the beard by moving the trimmer back against the flow of the beard.

Notes

• Be careful not to cut your hand on the blade when attaching and removing the comb attachment.
• Do not use with shaving creams applied or when the beard is wet. Wet beard can stick to the skin or clump making it difficult for the blade to cut.
• Comb beard and sideburns before trimming.
• Hair trimmings may collect inside the comb attachment when a large volume of beard is cut, so discard hair trimmings after each use.
• If the comb attachment is not attached properly, it may become loose during use resulting in excessive cutting.

Reading lamps when using

During use
All lamps disappear while using.

When the battery capacity is low
The battery capacity lamp blinks for 5 seconds when the power switch is pressed.

• You can shave 2 to 3 times after the battery capacity lamp blinks. (This will differ depending on usage.)
• A full charge will supply enough power for approx. 18 shaves of 3 minutes each. (This will differ depending on usage.)

Cleaning the device

Cleaning using the self-cleaning recharger

Preparing the self-cleaning recharger

Remove the shaver and the appliance plug from the self‑cleaning recharger.

1. Place the self-cleaning recharger on a hard, flat surface.
   • When the self‑cleaning recharger is lifted, or on the soft surface such as carpets, the lock release lever will not fit in the recharger properly. In that case, the cleaning liquid unit cannot be removed.
2. Press the cleaning liquid unit removal button ( ) and remove the cleaning liquid unit ( ).
   
3. Wash away the old cleaning liquid and beard trimmings and then rinse the cleaning liquid unit.
   • After washing, be sure to attach the cleaning liquid filter.
4. Pour tap water ( ) and detergent ( ) into the cleaning liquid unit.
   
   • Do not let the water rise above the maximum water line. This may cause the cleaning liquid to spill.
5. Attach the cleaning liquid unit.
   
   • Immediately wipe up any cleaning liquid that has been spilt.
     Be careful not to drop cleaning liquid onto leather products or wooden floors as it may cause discoloration.
6. Press the top of the selfcleaning recharger down and securely attach until it clicks.
   

Notes

• The water and detergent will mix after cleaning begins, making cleaning liquid.
• If "AUTO" mode cannot be selected or the STATUS lamp glows for 5 seconds when the SELECT button is pressed, the cleaning liquid needs to be replaced. Replace the cleaning liquid.
• When replaced, the cleaning liquid will last for approximately 30 days if used once per day. (This will differ depending on beard thickness and the ambient temperature.)
• Use the detergent within approximately 6 months after opening the package. When 6 months have passed, discard the cleaning liquid, and then pour new water and detergent into the cleaning liquid unit.
• Replace the water and detergent at the same time. Otherwise the cleaning function may deteriorate.
• Only use self‑cleaning recharger detergent for Panasonic shavers.

Cleaning the unit

Remove any soap or water on the shaver if it has been washed with hand soap or any other detergent.

Note
When cleaning the shaver after cutting a large volume of beard with the comb attachment, hair trimmings may collect in the cleaning tray of the self‑cleaning recharger. Discard hair trimmings from around the trimmer before attaching the shaver to the self‑cleaning recharger.

1. Insert the appliance plug into the self-cleaning recharger.
2. Pull up the arm until it clicks.
3. Remove the protective cap or comb attachment and then attach the shaver.
4. Push down the arm until it clicks.
5. Plug in the adaptor into a household outlet.
   • Turn the shaver off before attaching.
   • Check that the system outer foil is not deformed or damaged when you are attaching the shaver.
   • Put shaver into the self‑cleaning recharger with the trimmer handle retracted. If the trimmer handle is not retracted, it might scratch the cleaning tray.
6. Press the SELECT button to select the mode.
   • The "Charge" mode starts when attaching the shaver.
   • Each time you press the SELECT button, the mode changes from "AUTO" → "Charge".
   • The modes start approximately 6 seconds after they are selected.
   • The mode will be aborted if the power is cut off. In this case, perform the mode again from the beginning.
   • Do not press the cleaning liquid unit removal button as the cleaning liquid may spill causing a malfunction.

Mode	Time required (guide)
Charge	Charge 0 to 60 min
AUTO	Clean/Dry 10 min/350 min Charge 0 to 60 min It is not possible to change the mode after "AUTO" mode has started.

• Use the self‑cleaning recharger in temperatures between 5°C (41°F) and 35°C (95°F).
  The Clean or Dry function may not work out of recommended ambient temperature range. In such a case, "AUTO" mode cannot be selected and the STATUS lamp will glow for approximately 5 seconds.

Cleaning the unit without the self-cleaning recharger

1. Disconnect the cord from the shaver.
2. Apply some hand soap and some water to the system outer foil.
3. Turn the shaver on.
   
4. Turn off the shaver after 10 to 20 seconds.
5. Remove the outer foil section.
   
6. Clean the shaver, the outer foil section, the trimmer, and the comb attachment with running water.
   
7. Wipe off any drops of water with a dry cloth.
8. Dry the outer foil section, the shaver, the trimmer, and the comb attachment completely.
   
9. Attach the outer foil section to the shaver.
10. Lubricate the shaver.

Lubrication

To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used.

1. Switch off the shaver.
2. Apply one drop of oil to each system outer foil.
   
3. Raise the trimmer and apply one drop of oil.
4. Switch the shaver on, and run it for approximately five seconds.
5. Switch off the shaver, and wipe off any excess oil from the system outer foil with a soft cloth.

Replacing the system outer foil and the inner blades

system outer foil	once every year
inner blades	once every two years

Removing the outer foil section

Press the foil frame release buttons and lift the outer foil section upwards.

Attaching the outer foil section

Securely attach the outer foil section to the shaver until it clicks.

Replacing the system outer foil

1. Press the system outer foil release buttons and pull down the system outer foil.
2. Insert the system outer foil until it clicks.
   • Always attach the system outer foil in proper direction.
   • Always insert the system outer foil to the foil frame when attaching to the shaver.

Replacing the inner blades

1. Remove the inner blades one at a time.
   • Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand.
2. Insert the inner blades one at a time until they click.

Replacement parts

Replacement parts are available at your dealer or Service Center.

Replacement parts for ES‑RT97	System outer foil and inner blades	WES9013
	System outer foil	WES9097
	Inner blades	WES9068
Special Detergent for Shaver Cleaning & Charging System		WES4L03

Cleaning the self-cleaning recharger

Beard trimmings may become attached to the cleaning tray of the self‑cleaning recharger. Follow the steps below to remove them. We recommend doing this each time you change the cleaning liquid.

1. Be sure to remove the cleaning liquid unit and the appliance plug from the self‑cleaning recharger.
   
   • Be careful not to spill the cleaning liquid.
   • Some cleaning liquid components and skin oil may separate and adhere to the cleaning liquid unit and cleaning liquid filter. This does not indicate a problem.
2. Pour water as illustrated while tilting the cleaning liquid unit and shaking it gently.
   
   • You can clean with the cleaning liquid filter removed.
   • After washing, be sure to attach the cleaning liquid filter.
3. Gently wipe off any beard trimmings attached to the inside of the cleaning tray with a cloth or tissue paper dampened with water.
   
   • Clean the corners and uneven parts of the cleaning tray with a cotton swab dampened with water.
     

When the water does not drain from the cleaning tray

• Do not tilt the self‑cleaning recharger to pour out water. Doing so may cause the cleaning liquid in the cleaning liquid unit to spill or cause the self‑cleaning recharger to malfunction.

Beard trimmings may clog the drain at the bottom of the cleaning tray.
In this case, you cannot clean or dry the shaver.
Push the beard trimmings down through the drain with a toothpick etc.

Troubleshooting

Self-cleaning recharger
Problem	Action
The blade has not been thoroughly washed.	If the shaver is not cleaned for more than 2 weeks, first clean to remove beard trimmings.
	Do not add detergent and water except when replacing the cleaning liquid. Doing so may deteriorate the cleaning function. (See Cleaning using the self-cleaning recharger)
	After cleaning, oil‑like droplets may remain on the outside of the foil frame. This is the lubricating component of the cleaning liquid and does not indicate a problem. You may wipe it off with a soft cloth.
The STATUS lamp glows.	See below.
The mode does not start.	Check that the AC adaptor is connected to the self‑cleaning recharger, and that the AC adaptor is plugged in to a household outlet. (See Charging using the self-cleaning recharger)
	Confirm that the shaver is properly attached to the self‑ cleaning recharger. (See Charging using the self-cleaning recharger)
	The Clean or Dry function may stop out of recommended ambient temperature range. (5 – 35°C (41 – 95°F))
	Check if the STATUS lamp glows. (See below)
Cleaning liquid has accumulated in the cleaning tray.	Remove any waste, etc. that has accumulated in the drain at the bottom of the cleaning tray.
	If you use the self‑cleaning recharger when the shaver is wet or when soap or shaving gel is on the shaver, cleaning liquid may accumulate in the cleaning tray.
The cleaning liquid unit cannot be removed.	Place the self‑cleaning recharger on a hard, flat surface. When the self‑cleaning recharger is lifted, or on the soft surface such as carpets, the lock release lever will not fit in the recharger properly. In that case, the cleaning liquid unit cannot be removed.
Makes a loud sound.	During cleaning: The self‑cleaning recharger makes a loud sound due to the cleaning of the blades. After cleaning: The self‑cleaning recharger makes a loud sound due to the removal of water droplets in order to speed drying. The sound after cleaning is different from the sound during cleaning. The water level has dropped and it is removing water droplets from the blades after cleaning. This does not indicate a problem.
The shaver cannot be charged.	Gently wipe the metal terminal of the appliance socket and the charging terminal of the self‑ cleaning recharger with a cloth or tissue dampened with water.
The blades are not dry or are sticky.	The blades may not dry quickly due to temperature conditions. Wipe with a soft cloth before shaving.
The blades crack or	Do not insert any foreign objects into the recharger.
deform during cleaning.	Replace the system outer foil and/or inner blades. (See Replacing the system outer foil and the inner blades)
The cleaning liquid has foamed.	If you mix soapy water or hand soap with the detergent or use another detergent, the cleaning liquid will foam. Use the self‑ cleaning recharger after thoroughly washing and drying the shaver.
	Replace the cleaning liquid.
Cleaning liquid leaked from the cleaning liquid unit.	Do not press the cleaning liquid unit removal button during the mode.
	Place the self‑cleaning recharger horizontally.
	If you use the self‑cleaning recharger when the shaver is wet or when soap or shaving gel is on the shaver, cleaning liquid may leak.
When the STATUS lamp glows
Problem	Action
It is time to replace the cleaning liquid.	Pour new water and detergent into the cleaning liquid unit.
The cleaning liquid unit is not properly attached.	Properly attach the cleaning liquid unit.
The self‑cleaning recharger is tilted.	Place the self‑cleaning recharger on a horizontal surface.
After performing the above operation, press the SELECT button and select a mode.
When all self-cleaning recharger's lamps blink
Problem	Action
Appliance failure	Contact an authorized service center.
Shaver
Problem	Action
Shavings fly all over.	This can be improved by cleaning every time after shaving.
	Clean the inner blades.
System outer foil gets hot.	Apply oil. (See Replacing the system outer foil and the inner blades)
	Replace the system outer foil if it is damaged or deformed. (See Replacing the system outer foil)
Operating time is short even after charging.	Apply oil.
	When the number of operations per charge starts to decrease, the battery is nearing the end of its life.
Makes a loud sound.	Apply oil.
	Confirm that the blades are properly attached.
	Clean the system outer foil.
The odor is getting stronger.	This can be improved by cleaning every time after shaving.
You do not get as close a shave as before.	This can be improved by cleaning every time after shaving.
	Replace the system outer foil and/or inner blades. Expected life of system outer foil and inner blades: System outer foil: Approximately 1 year Inner blades: Approximately 2 years
	Apply oil.
The shaver cannot be charged with the self‑ cleaning recharger.	Gently wipe the metal terminal of the appliance socket and the charging terminal of the self‑ cleaning recharger with a cloth or tissue dampened with water.
Shaver stopped functioning.	Recommended ambient temperature for operation is 5 – 35°C (41 – 95°F). The shaver may stop functioning when out of recommended ambient temperature range.
	The battery has reached the end of its life.

If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorized by Panasonic for repair.

Battery life

The life of the battery is 3 years. The battery in this shaver is not intended to be replaced by consumers.

Removing the built-in rechargeable battery

ATTENTION:
A lithium ion battery that is recyclable powers the product you have purchased. Please call 1‑800‑8‑BATTERY for information on how to recycle this battery.

Remove the built-in rechargeable battery before disposing of the shaver.
This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction.

• Remove the shaver from the AC adaptor.
• Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.
• Perform steps to and lift the battery, and then remove it.
• Please take care not to short‑circuit the battery.

Specifications

Power source	See the name plate on the AC adaptor. (Automatic voltage conversion)
Motor voltage	3.6 V
Charging time	Approx. 1 hour

This product is intended for household use only.

Safety precautions

To reduce the risk of injury, loss of life, electric shock, fire, and damage to property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

	Denotes a potential hazard that will result in serious injury or death.
	Denotes a potential hazard that could result in serious injury or death.
	Denotes a hazard that could result in minor injury.

The following symbols are used to classify and describe the type of instructions to be observed.

	This symbol is used to alert users to a specific operating procedure that must not be performed.
	This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using this appliance.

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.
2. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
3. Except when charging, always unplug this appliance from the electrical outlet immediately after using.
4. Unplug this appliance before cleaning.

To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Close supervision is necessary when this appliance is used by, on, or near children or invalids.
2. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this appliance when it has a damaged cord or plug, when it is not working properly, after it has been dropped or damaged, or after it has been dropped into water. Return the appliance to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
7. Do not use this appliance with damaged shaving blades and/or foil, as it has the potential to result in facial injury.
8. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to "off" then remove plug from outlet.

SAVE THESE INSTRUCTIONS

This shaver has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, or leave in a high temperature environment.

• Doing so may cause overheating, ignition, or explosion.

Do not connect or disconnect the adaptor to a household outlet with a wet hand.

• Doing so may cause electric shock or injury.

Never disassemble except when disposing of the product.

• 
  Doing so may cause fire, electric shock, or injury.

Do not use anything other than the supplied AC adaptor and the self-cleaning recharger. Also, do not charge any other product with the supplied AC adaptor and the self-cleaning recharger.

• 
  Doing so may cause burn or fire due to a short circuit.

Do not modify or repair.

• 
  Doing so may cause fire, electric shock, or injury. Contact an authorized service center for repair (battery change etc).

Do not store with in reach of children or infants. Do not let the muse it.

• Putting the inner blades and/or the oil container in the mouth or drinking the detergent may cause accidents and injury.

Do not damage, modify, or forcibly bend, pull, or twist the cord.
Also, do not place anything heavy on or pinch the cord.

• Doing so may cause electric shock or fire due to a short circuit.

Do not use in away exceeding the rating of the household outlet or the wiring.

• Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating.

Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor. Fully insert the power plug.

• 
  Failure to do so may cause fire or electric shock.

Regularly clean the power plug and the appliance plug to prevent dust from accumulating.

• Failure to do so may cause fire due to insulation failure caused by humidity.
  Disconnect the adaptor and wipe with a dry cloth.

Immediately stop using and remove the adaptor if there is an abnormality or malfunction.

• 
  Using it in such conditions may cause fire, electric shock, or injury.

<Abnormality or malfunction cases>

• The main unit, self-cleaning recharger, adaptor or cord is deformed or abnormally hot.
• The main unit, self-cleaning recharger, adaptor or cord has burning smell.
• There is abnormal sound during use or charging of the main unit, self-cleaning recharger, adaptor or cord.
  • Immediately request inspection or repair at an authorized service center.

If detergent contacts skin, wash immediately and thoroughly with soap.
If you experience skin irritation any where on the body, stop using immediately and contact a physician.

• Failure to follow these instructions may result in physical injury or injury to the skin.

If detergent or oil is consumed accidentally, do not induce vomiting, drink a large amount of water and contact a physician.
If detergent or oil comes into contact with eyes, wash immediately and thoroughly with running water and contact a physician.

• Failure to follow these instructions may result in physical problems.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

• Failure to do so may cause an accident or injury.

The supply cord can not be replaced. If the cord is damaged, the AC adaptor should be discarded.

• Failure to do so may cause an accident or injury.

Do not allow pins or trash to adhere to the power plug or the appliance plug.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Do not use excessive pressure to apply the system outer foil to your lip or other part of your face. Do not apply the system outer foil directly to blemishes or injured skin.

• Doing so may cause injury to the skin.

Do not force fully press the system outer foil. Also, do not touch the system outer foil with fingers or nails when in use.

• Doing so may cause injury to skin or reduce the life of the system outer foil.

Do not touch the blade section (metallic section) of the inner blade.

• Doing so may cause injury to your hands.

Do not use this product for hair on head or any other part of the body.

• Doing so may cause injury to skin or reduce the life of the system outer foil.

Do not share your shaver with your family or other people.

• Doing so may result in infection or inflammation.

Do not remove the shaver from the self-cleaning recharger while using the "AUTO" mode.

• Doing so may cause burn due to high temperatures around the blades.

Do not wrap the cord around the adaptor when storing.

• Doing so may cause the wire in the cord to break with the load, and may cause fire due to a short circuit.

Do not use detergent for any purpose other than washing the shaver blades.

• Using it with other products may cause discoloration or cracking.

Check the system outer foilf or cracks or deformations before use.

• Failure to do so may cause injury to the skin.

Be sure to place the protective cap on the shaver when carrying around or storing.

• Failure to do so may cause injury to skin or reduce the life of the system outer foil.

Disconnect the adaptor or the appliance plug by holding onto the adaptor or the appliance plug instead of the cord.

• Failure to do so may cause electric shock or injury.

Use caution when opening detergent as spout is sharp.

• Failure to do so may cause injury.

Personal Care & Beauty Care Products

FOR USA AND PUERTO RICO ONLY

If you are dissatisfied with any Panasonic Personal Care & Beauty Care Products for any reason, simply return it to the place of purchase with a dated proof of purchase, in the original packaging, with all accessories, parts and instructions, within 30 days of the date of purchase, for a full refund, or call Panasonic at 1‑800‑338‑0552.

FOR YOUR CONVENIENCE, WE HAVE ESTABLISHED A TOLL-FREE (IN USA ONLY) NATIONAL ACCESSORY PURCHASE HOT LINE AT 1-800-332-5368.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Panasonic ES-RT97 - Rechargeable Shaver Manual