Panasonic ES-ST25 - Rechargeable Shaver Manual

Intended use

• This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean with water. The following symbol means suitable for use in a bath or shower.
  

► Notes

• Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method.
• Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged.
• If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time.
• Clean the housing only with a soft cloth slightly dampened with tap water or soapy tap water. Do not use thinner, benzine, alcohol or other chemicals.
• Store the shaver in a place with low humidity after use.
• Do not store the shaver where it will be exposed to direct sunlight or other heat sources.

Parts identification

1. Main body
   1. System outer foil
   2. Foil frame
   3. Foil frame release buttons
   4. Cleaning shutter
   5. Thumb rest
   6. Side terminals
   7. Power switch
   8. Shaving sensor lamp ( )
   9. Charge status lamp ( )
   10. Inner blades
   11. Trimmer
   12. Trimmer handle
   13. Outer foil section
   14. System outer foil release buttons
   15. Water inlet
2. AC adaptor (RE7-59)
   16. Adaptor
   17. Power plug
   18. Power cord
   19. Appliance plug
3. Charging stanв (RC9-83)
   20. Charging terminals
   21. Stand socket
4. Carrying holder

Before use

Using the carrying holder

The shaver can be kept vertically or horizontally. When transporting the shaver, you can use the carrying holder to protect the outer foil and prevent erroneous operation of the switch.

• When transporting the shaver, be sure to clean off any shavings before attaching the carrying holder.

Attaching the carrying holder

Attach the carrying holder as illustrated.

• Securely attach the carrying holder to the main unit.

Removing the carrying holder

Remove the carrying holder while pressing down on both sides.

Charging the device

You can charge the shaver with the carrying holder attached.

1. Insert the appliance plug into the stand socket.
   
2. Insert the shaver in the charging stand as illustrated.
   
   • The shaver will not charge unless the side terminals ( ) are in contact with the charging terminals ( ).
   • Wipe off any water droplets on the side terminals.
3. Plug in the adaptor into a household outlet.
   • Check that the charge status lamp glows.
   • Charging is completed after approx. 1 hour.
     The charging time may decrease depending on the charging capacity.
   • If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration.

While charging
The charge status lamp ( ) glows red.

After charging is completed
The charge status lamp ( ) turns off.

Abnormal charging
The charge status lamp ( ) will blink twice every second.

• After charging is completed, turning the power switch ON with the shaver plugged in will cause charge status lamp to light up and then turn off after 5 seconds. This shows that the shaver is fully charged.
• Recommended ambient temperature for charging is 10 – 35°C (50 – 95°F). It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures.
  The charge status lamp ( ) will blink twice every second when there is a problem with charging.
  Charge the shaver within the recommended ambient temperature range.
• When charging the shaver for the first time or when it has not been in use for more than 6 months, the charge status lamp ( ) may not glow. It will eventually glow if kept connected.

4. Disconnect the adaptor after charging is completed.
   • Charging the battery for more than 1 hour will not affect battery performance.

Note
You cannot operate the shaver while charging.

Using the unit

1. Press the power switch to select the desired shaving mode.
   • Each time you press the power switch, the shaving mode changes from "Shaving sensor mode" → "Normal mode" → "OFF."

Shaving sensor mode	Normal mode	OFF
Beard thickness is automatically sensed and the power is automatically adjusted when shaving.	The power level is constantly maintained while shaving.	—
The shaving sensor lamp ( ) glows blue.	The shaving sensor lamp ( ) turns off.	The shaving sensor lamp ( ) turns off.

• The shaving sensor may not respond depending on the thickness of the beard or the type of the shaving gel, but this is normal.

2. Hold the shaver as illustrated and shave.
   
   • Start shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.

You can also use a pen grip to hold the shaver.

Using the trimmer
Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns.

Notes

• Before shaving, check that the cleaning shutter is closed.
• Place your finger on the thumb rest while in use. Keeping your finger placed on the power switch during use may switch the mode or turn the shaver OFF.
• Do not use shaving creams or face cleansers containing scrubbing compounds as these may cause the outer foil to clog.
• We recommend using the shaver in an ambient temperature range of 5 – 35°C (41 – 95°F). If used outside this range, the appliance may stop operating.

Reading lamps when using
When the battery capacity is low
The charge status lamp ( ) blinks once every second when operating the shaver.

• You can shave 2 to 3 times after the charge status lamp ( ) blinks. (This will differ depending on usage.)
• A full charge will supply enough power for approx. 14 shaves of 3 minutes each.
• If the shaver is operated in the shaving sensor mode in a battery‑shortage condition, the shaving sensor lamp ( ) glows blue, and the charge status lamp ( ) blinks red.

Cleaning the device

Remove the shaver from the charging stand. Apply some hand soap and some water to the outer foil. Close the cleaning shutter. Turn the shaver on.
There are two ways to clean the shaver, depending on the actual dirt level.
To remove light dirt	To remove heavy dirt
Slide the cleaning shutter until it clicks. Clean the outer foil section with running water. Turn the shaver off. Rinse with water and shake up and down several times to remove the water.	Turn the shaver off after 10 – 20 seconds. Remove the outer foil section and turn the shaver on. Clean the shaver and the outer foil section with running water. Rinse with water and shake up and down several times to remove the water.
Be careful not to hit the main body on the sink or any other object while draining the water. Failure to do so may cause malfunction.
Wipe off any drops of water with a dry cloth. Dry the outer foil section and the shaver completely in a shaded area. The outer foil section will dry faster if removed from the main body. Attach the outer foil section to the shaver.

Replacing the system outer foil and the inner blades

system outer foil	once every year
inner blades	once every two years

Removing the outer foil section

Press the foil frame release buttons and lift the outer foil section upwards.

Attaching the outer foil section

After turning the water inlet surface to the front, securely attach the outer foil section to the shaver until it clicks.

Replacing the system outer foil

1. Press the system outer foil release buttons and pull down the system outer foil.
2. Align the water inlet surface and the system outer foil mark ( ) and securely attach together.
   • The system outer foil cannot be reversely attached.
   • Always insert the system outer foil to the foil frame when attaching to the shaver.

Replacing the inner blades

1. Remove the inner blades one at a time.
   • Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand.
2. Insert the inner blades one at a time until they click.

Replacement parts

Replacement parts are available at your dealer or Service Center.

Replacement parts for ES‑ST25	System outer foil and inner blades	WES9013
	System outer foil	WES9087
	Inner blades	WES9068

Troubleshooting

Problem	Action
Trimmed hairs fly all over.	This can be improved by cleaning every time after shaving.
	Clean the inner blades.
	Confirm that the cleaning shutter is firmly closed.
System outer foil gets hot.	Replace the system outer foil if it is damaged or deformed. (See Replacing the system outer foil and the inner blades)
The shaver cannot be properly cleaned even after water is poured from the water inlet.	Remove beard trimmings. When the shaver is very dirty, remove the foil frame and wash with water. (See Replacing the system outer foil and the inner blades)
The blades do not dry.	The blades may not dry quickly due to temperature conditions.
	The blades can be dried more easily by removing for drying.
The odor is getting stronger.	This can be improved by cleaning every time after shaving.
You do not get as close a shave as before.	This can be improved by cleaning every time after shaving.
	Replace the system outer foil and/ or inner blades. Expected life of system outer foil and inner blades: System outer foil: Approximately 1 year Inner blades: Approximately 2 years
The shaving sensor does not respond.	Depending on the beard thickness, the shaving sensor may not react and the driving sound may not change. This is not abnormal.
	The shaving sensor may not respond depending on the thickness of the beard or the type of the shaving gel, but this is normal.
The shaving sensor responds even though the shaver is not in contact with the skin.	Clean the beard trimmings from the shaver. When the shaver is extremely dirty, remove the foil frame and wash with water. (See Replacing the system outer foil and the inner blades)
	Replace the system outer foil and/or inner blades. Expected life of system outer foil and inner blades: System outer foil: Approximately 1 year Inner blades: Approximately 2 years
Makes a loud sound.	Confirm that the blades are properly attached.
	The shaver can be loud due to the linear motor. This does not indicate a problem.
The driving sound changes while shaving.	While the shaving sensor lamp glows, the shaving sensor is operating. The sound changes depending on the beard thickness.
The power will not switch to OFF.	Press the power switch twice while using in the shaving sensor mode.
The shaver cannot be charged.	Push the main body into the charging stand all the way and make sure the charge status lamp glows.
	Gently wipe the side terminals and the charging terminals of the charging stand with a cloth or tissue damped with water.
	The recommended temperature for charging is 10 – 35°C (50 – 95°F). If charged at a temperature other than the recommended temperature, the shaver may take longer to charge or may not charge at all.
Operating time is short even after charging.	When the number of operations per charge starts to decrease, the battery is nearing the end of its life.
Shaver stopped functioning.	Recommended ambient temperature for operation is 5 – 35°C (41 – 95°F). The shaver may stop functioning when out of recommended ambient temperature range.
	The battery has reached the end of its life.

Battery life

The life of the battery is 3 years if charged approximately once every two weeks. The battery in this shaver is not intended to be replaced by consumers.

Removing the built-in rechargeable battery

ATTENTION:
A lithium ion battery that is recyclable powers the product you have purchased. Please call 1‑800‑8‑BATTERY for information on how to recycle this battery.

Remove the built-in rechargeable battery before disposing of the shaver.
This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction.

• Remove the shaver from the charging stand.
• Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.
• Perform steps to and lift the battery, and then remove it.
• Please take care not to short‑circuit the battery.

Specifications

Power source	See the name plate on the AC adaptor. (Automatic voltage conversion)
Motor voltage	3.6 V
Charging time	Approx. 1 hour

This product is intended for household use only.

Safety precautions

To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

	Denotes a potential hazard that will result in serious injury or death.
	Denotes a potential hazard that could result in serious injury or death.
	Denotes a hazard that could result in minor injury.

The following symbols are used to classify and describe the type of instructions to be observed.

	This symbol is used to alert users to a specific operating procedure that must not be performed.
	This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using this appliance.

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.
2. Charger unit is not for immersion or for use in shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
4. Except when charging, always unplug this appliance from the electrical outlet immediately after using.
5. Unplug this appliance before cleaning.
6. Do not use an extension cord with this appliance.

To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Close supervision is necessary when this appliance is used by, on, or near children or invalids.
2. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
7. Do not use this appliance with damaged shaving blades and/or foil, as it has the potential to result in facial injury.
8. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to "off" then remove plug from outlet.

SAVE THESE INSTRUCTIONS

This shaver has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, or leave in a high temperature environment.

• Doing so may cause overheating, ignition, or explosion.

Always unplug the adaptor from a household outlet when cleaning.

• Failure to do so may cause electric shock or injury.

Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor.
Fully insert the adaptor or appliance plug.

• 
  Failure to do so may cause fire, electric shock, or burn.

Regularly clean the power plug, the appliance plug and the side terminals to prevent dust from accumulating.

• Failure to do so may cause fire due to insulation failure caused by humidity.
  Disconnect the adaptor and wipe with a dry cloth.

Immediately stop using and remove the adaptor if there is an abnormality or failure.

• 
  Using it in such conditions may cause fire, electric shock, or injury.

<Abnormality or failure cases>

• The main unit, adaptor, or power cord is deformed or abnormally hot.
• The main unit, adaptor, or power cord smells of burning.
• There is abnormal sound during use or charging of the main unit, adaptor, or power cord.
  • Immediately request inspection or repair at an authorized service center.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should b esupervised to ensure that they do not play with the appliance.

• Failure to do so may cause an accident or injury.

The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.

• Failure to do so may cause an accident or injury.

Do not connect or disconnect the adaptor to a household outlet with a wet hand.

• Doing so may cause electric shock or injury.

Do not immerse the AC adaptor and the charging stand in water or wash with water.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Never use the AC adaptor and the charging stand in the bathroom or shower room.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Do not use anything other than the supplied AC adaptor and the charging stand. Also, do not charge any other product with the supplied AC adaptor and the charging stand.

• 
  Doing so may cause burn or fire due to shorting.

Never use the appliance if the AC adaptor is damaged or if the plug fits loosely in a household outlet.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Do not damage, break, modify, or forcibly bend, pull, or twist the power cord.
Also, do not place anything heavy on or pinch the power cord.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Do not use in away exceeding the rating of the household outlet or the wiring.

• Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating.

Do not modify or repair.

• 
  Doing so may cause fire, electric shock, or injury. Contact an authorized service center for repair (battery change, etc.).

Do not store with in there ach of children or infants. Do not let them use it.

• Putting the inner blades in the mouth may cause accidents and injury.

Never disassemble except when disposing of the product.

• 
  Doing so may cause fire, electric shock, or injury.

Disconnect the adaptor from the household outlet when not charging.

• 
  Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.

Check the system outer foil for cracks or deformations before use.

• Cracks or deformations of the system outer foil may result in injury to the skin.

Be sure to place the shaver in it scarrying holder when carrying around or storing.

• Failure to do so may cause injury to skin or reduce the life of the system outer foil.

Disconnect the adaptor or the appliance plug by holding onto them instead of the power cord.

• Disconnecting by holding onto the power cord may cause electric shock or injury.

Do not allow pins or trash to adhere to the power plug, the appliance plug or the side terminals.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Do not use excessive pressure to apply the outer foil to your lip or other part of your face. Do not apply the outer foil directly to blemishes or injured skin.

• Doing so may cause injury to the skin.

Do not forcefully press the blades. Also, do not touch the system outer foil with fingers or nails when in use.

• Doing so may cause injury to skin or reduce the life of the system outer foil.

Do not touch the blade section (metallic section) of the inner blade.

• Doing so may cause injury to your hands.

Do not use this product for hair on head or any other part of the body.

• Doing so may cause injury to skin or reduce the life of the system outer foil.

Do not share your shaver with your family or other people.

• Doing so may result in infection or inflammation.

Do not drop or subject to shock.

• Doing so may cause injury.

Do not wrap the power cord around the Adaptor or the charging stand when storing.

• Doing so may cause the wire in the power cord to break with the load, and may cause fire due to shorting.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Panasonic ES-ST25 - Rechargeable Shaver Manual