Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG AMLLGN
Summary of Contents for AEG AMLLGN
- Page 1 For sign-off review, sent 4 Aug 2023. AMLLGN Original instructions...
-
Page 2: Table Of Contents
For sign-off review, sent 4 Aug 2023. CONTENTS Important safety instructions .......................1 Maintenance ..........................2 Technical data..........................2 Speci c conditions of use ......................2 Overview.............................3 Low battery indication .........................4 Changing batteries ........................4 Adjustable legs ...........................5 Magnetic wall mount and green target plate ................5 Working in self-leveling mode .....................6 Working in manual mode ......................7 Plumb function ..........................8... - Page 3 For sign-off review, sent 4 Aug 2023. WARNING: Avoid direct eye exposure. The laser beam can cause severe eye damage and/or blindness. Do not stare into the laser beam or direct it towards other people. Caution! The laser-emitting product may be behind you while you are working on other projects. Be careful when facing the product.
-
Page 4: Maintenance
For sign-off review, sent 4 Aug 2023. MAINTENANCE Wipe the aperture lens and the body of the product with a clean, soft cloth. Do not use solvents. Although the product is dust and dirt-resistant to a certain degree, do not store it in dusty places as long term exposure may damage internal moving parts. -
Page 5: Speci C Conditions Of Use
For sign-off review, sent 4 Aug 2023. Laser plumb Laser point wavelength 635 ± 5 nm Laser Class II Laser point max. power < 1 mW Plumb accuracy ± 0.6 mm / 1 m Laser point colour Working range 5 m Recommended ambient operating -10°C - +45 °C temperature... -
Page 6: Overview
For sign-off review, sent 4 Aug 2023. OVERVIEW Stabilising rubber sleeve Adjustable legs Forward vertical laser beam window Horizontal laser beam window / OFF locking switch Side vertical laser beam window Battery door Red plumb spot 1/4" tripod mount 6ENGLISH... - Page 7 For sign-off review, sent 4 Aug 2023. Keypad Manual mode LED indicator Manual mode button Turn on or off the manual mode. Beam selector LED indicator (continuous light) Low battery LED indicator ( ashing light) Beam selector button Choose between Vertical beam forward, side Vertical beam, Horizontal beam forward, or a combination of these beams.
-
Page 8: Low Battery Indication
For sign-off review, sent 4 Aug 2023. LOW BATTERY INDICATION When the voltage is low, the brightness of the laser is reduced and the low battery indication (green LED near the V/H button) flashes once every 0.5 seconds. It is still possible to continue the work, but the product will automatically shut down when the voltage is too low. -
Page 9: Changing Batteries
For sign-off review, sent 4 Aug 2023. CHANGING BATTERIES Change the batteries when the laser beams begin to dim. If the product is not in use for a long period of time, remove the batteries from the battery compartment. This will prevent batteries from leaking and causing corrosion damage. 3 x 1.5 V AA LR06 click... -
Page 10: Adjustable Legs
For sign-off review, sent 4 Aug 2023. ADJUSTABLE LEGS Use the adjustable legs to adjust the Use the adjustable legs to tilt the product to height of the horizontal beam. set any slope required. 10 ENGLISH ENGLISH... -
Page 11: Magnetic Wall Mount And Green Target Plate
For sign-off review, sent 4 Aug 2023. MAGNETIC WALL MOUNT AND GREEN TARGET PLATE Use the magnetic wall mount to fi x the product to a wall or metallic structures or similar. Use the green target plate to improve visibility of the laser beam in unfavourable conditions and at greater distances. -
Page 12: Working In Self-Leveling Mode
For sign-off review, sent 4 Aug 2023. WORKING IN SELF-LEVELING MODE In self-leveling mode, the product will level itself in a ±3° range and can project a horizontal beam, two vertical beams, or all three beams simultaneously. Place the product on a solid, 1/4"... - Page 13 For sign-off review, sent 4 Aug 2023. Choose your preferred beam by pressing the V/H beam button. > 3° > 3° If the initial level of the product is beyond ± 3° and the self-leveling mode is activated, the laser beams >...
-
Page 14: Working In Manual Mode
For sign-off review, sent 4 Aug 2023. WORKING IN MANUAL MODE In manual mode, the product's self-leveling mechanism is disabled and the laser lines can be set at any slope required. Place the product on a solid, flat, vibration-free surface or on a tripod. - Page 15 For sign-off review, sent 4 Aug 2023. Choose your preferred beam by pressing the V/H beam button. Tilt the product using the adjustable folding legs and adjust to the preferred angle and height. To turn off the manual mode , press the manual button again.
-
Page 16: Plumb Function
For sign-off review, sent 4 Aug 2023. PLUMB FUNCTION With the plumb function, a point on the floor can be projected perpendicularly to the ceiling. The point of reference from the fl oor is aligned with the intersection of the cross line on the ceiling. -
Page 17: Pulse Mode Function
For sign-off review, sent 4 Aug 2023. PULSE MODE FUNCTION For outdoor work under direct sunlight or bright conditions and for extended indoor ranges of up to 50 m / 164 ft., use the pulse mode with a detector. A detector is not included and must be purchased separately. When the pulse mode is activated, the laser beams will fl ash at a very high frequency (invisible to the human eye). -
Page 18: Accuracy Check
For sign-off review, sent 4 Aug 2023. ACCURACY CHECK The product is factory calibrated. AEG recommends the user to check the accuracy of the laser periodically, especially if the product falls or is mishandled. If the maximum deviation of the laser is exceeded in one of the accuracy checks, contact one of our AEG service agents (see our list of guarantee/service addresses). - Page 19 For sign-off review, sent 4 Aug 2023. 5. Turn the laser 180° towards wall B and mark the centre of the cross beams as b1 on the wall. 180° 6. Move the laser level towards wall B and position it approximately 0.5 m from wall B. 7.
- Page 20 For sign-off review, sent 4 Aug 2023. CHECKING THE LEVEL ACCURACY OF THE HORIZONTAL BEAM (SIDE TO SIDE INCLINATION) For this check, a free surface of approximately 5 x 5 m is required. 1. Set up the product on a tripod or on a solid surface between two walls A and B, approximately 5 m apart.
- Page 21 For sign-off review, sent 4 Aug 2023. 5. Move the product approximately 5 m away and turn the laser 180° towards wall A and B. 6. Mark the centre of the laser line point a2 on wall A and point b2 on wall B. 7.
- Page 22 For sign-off review, sent 4 Aug 2023. CHECKING THE LEVEL ACCURACY OF THE VERTICAL BEAM 1. Hang an approximately 4 m plumb line on a wall. 2. After the plumb line has settled, mark point a1 on the wall, behind the plumb line and near the plumb cone.
- Page 23 For sign-off review, sent 4 Aug 2023. CHECKING 90º ACCURACY BETWEEN THE TWO VERTICAL BEAMS This procedure requires a room of at least 5 x 5 m with four walls. 1. Set up the product on a table or on the the floor in the middle of the room.
- Page 24 For sign-off review, sent 4 Aug 2023. CHECKING 90º ACCURACY BETWEEN THE TWO VERTICAL BEAMS 5. Rotate the product clockwise so that the forward laser beam passes through marks b1 on the table and b2 on wall B. 6. Mark the centre of the side vertical beam at two 90°...
- Page 25 For sign-off review, sent 4 Aug 2023. 9. Rotate the product clockwise so that the forward laser beam passes through marks d1 on the table and d2 on wall D. 10. Mark the centre of the side vertical beam at two 90°...
- Page 26 For sign-off review, sent 4 Aug 2023. CHECKING PLUMB ACCURACY This procedure requires a room with approximately 5 m distance between fl oor and ceiling. 1. Open the folding legs of the laser and place it on the oor. 2.
- Page 27 For sign-off review, sent 4 Aug 2023.
- Page 28 Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC, 3149, Australia Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, AEG is a registered trade mark used under Highbrook, Auckland 2013, New Zealand license from AB Electrolux (publ). 20230727v1...