Related Manuals for Makita UB003C
Summary of Contents for Makita UB003C
- Page 1 INSTRUCTION MANUAL Battery Powered Blower UB003C Read before use. Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: UB003C Capacities Air volume 2.9 - 17.6 m /min Air speed (average) 11.7 - 71.9 m/s Air speed (max.) 86.0 m/s Overall length (with end nozzle) 913 mm / 963 mm / 1,013 mm Rated voltage D.C. 36 V - 40 V max Net weight 2.8 - 3.1 kg... - Page 3 Work area safety Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away Keep work area clean and well lit. Cluttered or from moving parts. Loose clothes, jewellery or dark areas invite accidents. long hair can be caught in moving parts. Do not operate power tools in explosive atmo- If devices are provided for the connection of spheres, such as in the presence of flammable...
- Page 4 Keep cutting tools sharp and clean. Properly Battery Powered Blower Safety maintained cutting tools with sharp cutting edges Instructions are less likely to bind and are easier to control. Use the power tool, accessories and tool bits etc. in accordance with these instructions, tak- WARNING: Read all safety warnings and ing into account the working conditions and all instructions.
- Page 5 20. Avoid operating the blower for a long time in Inspect the cord before operating the machine. low temperature environment. If the cord is damaged, ask Makita Authorized 21. Do not use the machine when there is a risk of Service Centers for repair.
- Page 6 Use power tools only with specifically desig- WARNING: DO NOT let comfort or familiarity nated battery packs. Use of any other battery with product (gained from repeated use) replace packs may create a risk of injury and fire. strict adherence to safety rules for the subject When battery pack is not in use, keep it away product.
- Page 7 ► 1 . Triangle mark 2. End nozzle 3. Front pipe To remove the end nozzle, perform the installation CAUTION: Only use genuine Makita batteries. procedure in reverse. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting NOTE: The length of the nozzle can be changed by causing fires, personal injury and damage. It will moving the nozzle as shown in the figure.
-
Page 8: Functional Description
Turn the machine off, and then turn it on again to restart. Fig.4 Charge the battery(ies) or replace it/them with ► 1 . Flat nozzle 2. Adapter pipe recharged battery(ies). Let the machine and battery(ies) cool down. If no improvement can be found by restoring protection system, then contact your local Makita Service Center. NOTICE: If the machine stops due to a cause not described above, refer to the section for troubleshooting. 8 ENGLISH... -
Page 9: Main Power Switch
Main power switch Battery indicator status Remaining battery capacity WARNING: Always turn off the main power Blinking switch when not in use. 50% to 100% To turn on the machine, press the main power switch. The speed indicators light up in green. To turn off, press and hold the main power switch until the speed indica- 20% to 50% tors go off. -
Page 10: Operation
If you put on the shoulder harness not recommended by Makita and the shoulder harness of the back- pack-type power supply at the same time, removing the machine or backpack-type power supply is dif- ficult in case of an emergency, and it may cause an accident or injury. For the recommended hanging band, ask Makita Authorized Service Centers. CAUTION: Before operation, make sure that the buckles on the waist belt is locked and the machine is securely attached to the hook of the hanging band. CAUTION:... - Page 11 Remove the battery from the shoulder harness Put on the shoulder harness of the portable power assembly, and then pull out the cord from the left side of pack and lock the buckle of the waist belt, and lock the the battery. Attach the battery to the shoulder harness buckle of the chest belt (for PDC1500 only). assembly, and then attach the cord to the cord holders. Fig.13 Attach the hooks of the hanging band to the hang- ers of the machine. Fig.11 ► 1 .
-
Page 12: Blower Operation
Adjust the length of the hanging band as necessary. Press the main power switch to turn on the machine. The machine is ready to operate. The machine will run when you pull the switch trigger. NOTE: Attach the cord of the machine to the cord holder of the waist belt as shown in the figure (for PDC1500 only). Fig.18 ► 1 . Cord holder Fig.16 Insert the plug of the machine into the socket of Blower operation the portable power pack. -
Page 13: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should Fig.20 be performed by Makita Authorized or Factory Service ► 1 . Buckle Centers, always using Makita replacement parts. Cleaning the machine Clean the machine by wiping off dust with a dry cloth or one dipped in soapy water and wrung out. Fig.22... - Page 14 NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. Remove dust or dirt from the suction inlet at the rear of the machine. Fig.23 ► 1 . Suction inlet Storage Before storing the machine, disconnect the portable power pack from the machine, and perform full main- tenance.
-
Page 15: Troubleshooting
Remove the battery immediately! OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita prod- uct specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. - Page 16 Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885A56-921 www.makita.com 20230919...