Table of Contents
Advertisement
Available languages
Available languages
7.
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Power tool use and care
1.
Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
2.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
3.
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
Store idle power tools out of the reach of chil-
4.
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
Table 1: Minimum gage for cord
Ampere Rating
More Than
Not More Than
0 A
6 A
10 A
10 A
12 A
12 A
16 A
This tool should be grounded while in use to protect the oper-
ator from electric shock. The tool is equipped with a three-con-
ductor cord and three-prong grounding type plug to fit the
proper grounding type receptacle. The green (or green and yel-
low) conductor in the cord is the grounding wire. Never connect
the green (or green and yellow) wire to a live terminal. Your unit
is for use on 120 volts and has a plug shown in the figure.
► 1. Grounding Blade 2. Cover of Grounded Outlet
Box
Volts
120V
220V - 240V
6 A
–
1
6.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Service
1.
Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2.
Follow instruction for lubricating and chang-
ing accessories.
3.
Keep handles dry, clean and free from oil and
grease.
USE PROPER EXTENSION CORD. Use only three-wire
extension cords that have three-prong grounding-type
plugs and three-pole receptacles that accept the tool's
plug. Make sure your extension cord is in good condition.
Replace or repair damaged or worn cord immediately.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. Table 1 shows the cor-
rect size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
Total length of cord in feet
25 ft.
50 ft.
50 ft.
100 ft.
AWG
18
18
16
14
Concrete vibrator safety warnings
1.
Always keep your hands and face away from
vibrating head when operating.
2.
Switch off the tool immediately if you notice
abnormal noise or something faulty during
operation.
3.
Inspect the tool carefully for breakage, cracks
or deformation if you accidentally drop it or
strike it against something.
4.
Do not carry the tool with finger on switch.
Do not set the tool down and switch it on. The
5.
vibrating head may whip around out of control
and cause an accident.
6.
Be careful not to allow water, wet concrete or
the like to get into the tool. Do not let the tool
fall into wet concrete.
7.
Insert the vibrating head carefully between
iron/steel frames or reinforcing rods not to
2
come in contact with them.
8.
Do not crush or twist the flexible hose.
9.
Do not overly bend the flexible hose.
3 ENGLISH
100 ft.
200 ft.
16
16
16
14
16
14
12
Not Recommended
150 ft.
300 ft.
14
12
12
Advertisement
Table of Contents
